journal article·2010-10

Effect of Friction Stir Processing on Microstructure and Tensile Properties of an Investment Cast Al-7Si-0.6Mg Alloy

Saumyadeep Jana, Rajiv S. Mishra, John A. Baumann, Glenn J. Grant

Publisher page

Abstract

Friction stir processing (FSP) is emerging as a promising tool for microstructural modification. The current study assesses the effects of FSP on the microstructure and mechanical properties of an investment cast Al-7Si-Mg alloy. FSP eliminates porosity and significantly refines eutectic Si particles. The extent of particle refinement varied with changes in processing conditions. A high tool rotation rate and a low-to-intermediate tool traverse speed generated a higher volume fraction of finer particles. Tensile ductility changed significantly as a result of FSP, whereas ultimate tensile strength improved only marginally. Yield strength was similar in both cast and FSP samples under various heat-treated conditions, with the highest value obtained after a T6 heat treatment. Furthermore, FSP caused significant grain refinement in the stir zone, subsequently transforming into very coarse grains as abnormal grain growth occurred during solution treatment at high temperature.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. D.L. Zhang and L. Zheng: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3983-91.10.1007/BF02595647 ↗
2. T. Din and J. Campbell: Mater. Sci. Technol., 1996, vol. 12, pp. 644-50.10.1179/mst.1996.12.8.644 ↗
3. Y.B. Yu, P.Y. Song, S.S. Kim, and J.H. Lee: Scripta Mater., 1999, vol. 41, pp. 767-71.10.1016/S1359-6462(99)00215-8 ↗
4. J. Jorstad and W. Rasmussen: Aluminum Casting Technology, 2nd D.L. Zalensas, ed., AFS Inc., Schaumburg, IL, 1993, p. 77.
5. S. Kumai, J. Hu, Y. Higo, and S. Nunomura: Acta. Mater., 1996, vol. 44, pp. 2249-57.10.1016/1359-6454(95)00357-6 ↗
6. B. Zhang, D.R. Poirier, and W. Chen: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2659-66.10.1007/s11661-999-0306-3 ↗
7. M.E. Seniw, J.G. Conley, and M.E. Fine: Mater. Sci. Eng. A, 2000, vol. A285, pp. 43-48.10.1016/S0921-5093(00)00663-8 ↗
8. G. Atxaga, A. Pelayo, and A.M. Irisarri: Mater. Sci. Technol., 2001, vol. 17, pp. 446-50.10.1179/026708301101510023 ↗
9. K.T. Kashyap, S. Murali, K.S. Raman, and K.S.S. Murthy: Mater. Sci. Technol., 1993, vol. 9, pp. 189-203.10.1179/mst.1993.9.3.189 ↗
10. L. Wang and S. Shivkumar: Z. Metallkd., 1995, vol. 86, pp. 441-45.
11. T.J. Hurley and R.G. Atkinson: Trans. Am. Foundry Soc., 1985, vol. 91, pp. 291-96.
12. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Templesmith, and C.J. Dawes: Patent UK 9125978.8, 1991.
13. Z.Y. Ma, S.R. Sharma, and R.S. Mishra: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 3323-36.10.1007/BF02586167 ↗
14. M.L. Santella, T. Engstrom, D. Storjohann, and T.Y. Pan: Scripta Mater., 2005, vol. 53, pp. 201-06.10.1016/j.scriptamat.2005.03.040 ↗
15. K. Nakata, Y.G. Kim, H. Fujii, T. Tsumura, and T. Komazaki: Mater. Sci. Eng. A, 2006, vol. 437, pp. 274-80.10.1016/j.msea.2006.07.150 ↗
16. Z.Y. Ma, A.L. Pilchak, M.C. Juhas, and J.C. Williams: Scripta Mater., 2008, vol. 58, pp. 361-66.10.1016/j.scriptamat.2007.09.062 ↗
17. Z.Y. Ma: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 642-58.10.1007/s11661-007-9459-0 ↗
18. Y.J. Kwon, N. Saito, and I. Shigematsu: J. Mater. Sci. Lett., 2002, vol. 21, pp. 14737-6.10.1023/A:1020067609451 ↗
19. Y.S. Sato, M. Urata, and H. Kokawa: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 625-35.10.1007/s11661-002-0124-3 ↗
20. W.J. Arbegast: Hot Deformation of Aluminum Alloys III, ed. Z. Jin, TMS, Warrendale, PA, 2003, pp. 313–27.
21. H. Schmidt, J. Hattel, and J. Wert: Modelling Simul. Mater. Sci. Eng., 2004, vol. 12, pp. 143-57.10.1088/0965-0393/12/1/013 ↗
22. S. Murali, K.S. Raman, and K.S.S. Murthy: Mater. Sci. Forum, 1996, vol. 217-22, pp. 207-12.10.4028/www.scientific.net/MSF.217-222.207 ↗
23. Q.G. Wang: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2887-99.10.1007/s11661-003-0189-7 ↗
24. L. Backurud, G. Chai, and J. Tamminen: Solidification Characteristics of aluminum Alloys, AFS/SKANAluminum, Des Plaines, IL, 1990, p. 128.
25. Z.Y. Ma, S.R. Sharma, and R.S. Mishra: Mater. Sci. Eng. A, 2006, vol. 433, pp. 269-78.10.1016/j.msea.2006.06.099 ↗
26. D.A. Porter and K.E. Easterling: Phase Transformations in Metals and Alloys, 2nd ed., Taylor and Francis, New York, NY, 1992.10.1007/978-1-4899-3051-4 ↗
27. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Pergamon, Oxford, UK, 2002.
28. J-Q. Su, T.W. Nelson, and C.J. Sterling: Scripta Mater., 2005, vol. 52, pp. 135-40.10.1016/j.scriptamat.2004.09.014 ↗
29. K.V. Jata and S.L. Semiatin: Scripta Mater., 2000, vol. 43, pp. 743-49.10.1016/S1359-6462(00)00480-2 ↗
30. J-Q. Su, T.W. Nelson, R. Mishra, and M. Mahoney: Acta Mater., 2003, vol. 51, pp. 713-29.10.1016/S1359-6454(02)00449-4 ↗
31. R.W. Fonda, J.F. Bingert, and K.J. Colligan: Scripta Mater., 2004, vol. 51, pp. 243-48.10.1016/j.scriptamat.2004.04.017 ↗
32. P.B. Prangnell and C.P. Heason: Acta Mater., 2005, vol. 53, pp. 3179-92.10.1016/j.actamat.2005.03.044 ↗
33. C.G. Rhodes, M.W. Mahoney, W.H. Bingel, and M. Calabrese: Scripta Mater., 2003, vol. 48, pp. 1451-55.10.1016/S1359-6462(03)00082-4 ↗
34. J-Q. Su, T.W. Nelson, and C.J. Sterling: J. Mater. Res., 2003, vol. 18, pp. 1757-60.10.1557/JMR.2003.0243 ↗
35. J-Q. Su, T.W. Nelson, and C.J. Sterling: Phil. Mag., 2006, vol. 86, pp. 1-24.10.1080/14786430500267745 ↗
36. M. Karlsen, S. Tangen, J. Hjelen, O. Frigarrd, and O. Grong: 3 rd Int. FSW Symp., Awaji Island, Japan, 2001.
37. R.S. Mishra, R.K. Islamgaliev, T.W. Nelson, Y. Hovanski, and M.W. Mahoney: Friction Stir Welding and Processing, TMS, New York, NY, 2001.
38. ASM: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, vol. 2, ASM INTERNATIONAL, Materials Park, OH, 1990.
39. D. Apelian, S. Shivkumar, and G. Sigworth: Trans. Am. Foundry Soc., 1989, pp. 727–42.
40. G.E. Totten and D.S. MacKenzie: Handbook of Aluminum, vol. 1, Marcel Dekker, New York, NY, 2003.
41. S. Shivkumar, C. Keller, and D. Apelian: Trans. Am. Foundry Soc., 1990, pp. 905–11.