An EBSD Study of the Deformation of Service-Aged 316 Austenitic Steel
Source abstract
Abstract
Electron backscatter diffraction (EBSD) has been used to examine the plastic deformation of an ex-service 316 austenitic stainless steel at 297K and 823K (24 °C and 550 °C)at strain rates 3.5x10-3 to 4 x 10-7 s-1. The distribution of local misorientations was found to depend on the imposed plastic strain following a lognormal distribution at true strains < 0.1 and a gamma distribution at strains > 0.1. At 823 K (550 °C), the distribution of misorientations depended on the applied strain rate. The evolution of lattice misorientations with increasing plastic strain up to 0.23 was quantified using the metrics kernel average misorientation, average intragrain misorientation, and low angle misorientation fraction. For strain rate down to 10-5 s-1 all metrics were insensitive to deformation temperature, mode (tension vs. compression) and orientation of the measurement plane. The strain sensitivity of the different metrics was found to depend on the misorientation ranges considered in their calculation. A simple new metric, proportion of undeformed grains, is proposed for assessing strain in both aged and unaged material. Lattice misorientations build up with strain faster in aged steel than in un-aged material and most of the metrics were sensitive to the effects of thermal aging. Ignoring aging effects leads to significant overestimation of the strains around welds. The EBSD results were compared with nanohardness measurements and good agreement established between the two techniques of assessing plastic strain in aged 316 steel.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. P. Marshall: Austenitic Stainless Steels: Microstructure and Mechanical Properties, Elsevier Applied Science, Essex, 1984, pp. 80–102, 185.
2. J.R. Davis: ASM Speciality Handbook: Stainless Steel, ASM International, Materials Park, Ohio, 1994, pp. 20–32.
3. D. Fahr: Analysis of Stress-Strain Behavior of Type 316 Stainless Steel, OAK Ridge National Laboratory, Tennessee, 1973, pp. 1–22.10.2172/4388210 ↗
4. P.L. Andresen, and M.M. Morra: J. Nucl. Mater., 2008, vol. 383, pp. 97-111.10.1016/j.jnucmat.2008.08.005 ↗
5. J. Hou, Q.J. Peng, T. Shoji, J.Q. Wang, E.H. Han, and W. Ke: Corros. Sci., 2011, vol. 53, pp. 2956-62.10.1016/j.corsci.2011.05.037 ↗
6. A. Turnbull, K. Mingard, J.D. Lord, B. Roebuck, D.R. Tice, K.J. Mottershead, N.D. Fairweather, and A.K. Bradbury: Corros. Sci., 2011, vol. 53, pp. 3398-415.10.1016/j.corsci.2011.06.020 ↗
7. M. Kamaya: Mater. Charact., 2009, vol. 60, pp. 125-32.10.1016/j.matchar.2008.07.010 ↗
8. P.J. Buchanan, V. Randle, and P.E.J. Flewitt: Scr. Mater., 1997, vol. 37, pp. 1511-18.10.1016/S1359-6462(97)00245-5 ↗
9. K. Masayuki: Ultramicroscopy, 2011, vol. 111, pp. 1189-99.10.1016/j.ultramic.2011.02.004 ↗
10. R. Yoda, T. Yokomaku, and N. Tsuji: Mater. Charact., 2010, vol. 61, pp. 913-22.10.1016/j.matchar.2010.05.006 ↗
11. K.Z. Baba-Kishi: J. Mater. Sci., 2002, vol. 37, pp. 1715-46.10.1023/A:1014964916670 ↗
12. R.A. Schwarzer, D.P. Field, B.L. Adams, M. Kumar, and A.J. Schwartz: in Electron Backscatter Diffraction in Materials Science, A.J. Schwartz, M. Kumar, and B.L. Adams, eds., Kluwer Academic/Plenum Publishers, London, 2009, pp. 1–19.10.1007/978-0-387-88136-2_1 ↗
13. A. Arsenlis, and D.M. Parks: Acta Mater., 1999, vol. 47, pp. 1597-611.10.1016/S1359-6454(99)00020-8 ↗
14. A.J. Wilkinson, and D.J. Dingley: Acta Metall. Mater., 1991, vol. 39, pp. 3047-55.10.1016/0956-7151(91)90037-2 ↗
15. T. Maitland and S. Sitzman: in Scanning Microscopy for Nanotechnology: Techniques and Applications, W. Zhou and Z.L. Wang, eds., Springer Science, New York, 2007, pp. 41–75.10.1007/978-0-387-39620-0_2 ↗
16. F.J. Humphreys: J. Mater. Sci., 2001, vol. 36, pp. 3833-54.10.1023/A:1017973432592 ↗
17. S.I. Wright, M.M. Nowell, and D.P. Field: Microsc. Microanal., 2011, vol. 17, pp. 316-29.10.1017/S1431927611000055 ↗
18. M. Kamaya, A.J. Wilkinson, and J.M. Titchmarsh: Acta Mater., 2006, vol. 54, pp. 539-48.10.1016/j.actamat.2005.08.046 ↗
19. M. Kamaya, A.J. Wilkinson, and J.M. Titchmarsh: Nucl. Eng. Des., 2005, vol. 235, pp. 713-25.10.1016/j.nucengdes.2004.11.006 ↗
20. A. Sáez-Maderuelo, L. Castro, and G. Diego: J. Nucl. Mater., 2011, vol. 416, pp. 75-79.10.1016/j.jnucmat.2010.11.092 ↗
21. J.J. Sanchez-Hanton, and R.C. Thomson: Mater. Sci. Eng. A, 2007, vol. 460-461, pp. 261-67.10.1016/j.msea.2007.01.077 ↗
22. E.M. Lehockey, Y. Lin, and O.E. Lepik: in Electron Backscatter Diffraction in Materials Science, A.J. Schwartz, M. Kumar, and B.L. Adams, eds., Kluwer Academic, New York, 2000, pp. 247–60.10.1007/978-1-4757-3205-4_20 ↗
23. J. Kang, B. Bacroix, H. Regle, K. Oh, and H. Lee: Acta Mater., 2007, vol. 55, pp. 4935-46.10.1016/j.actamat.2007.05.014 ↗
24. C. Fukuoka, K. Morishima, H. Yoshizawa, and K. Mino: Scr. Mater., 2002, vol. 46, pp. 61-66.10.1016/S1359-6462(01)01197-6 ↗
25. R. M’Saoubi, and L. Ryde: Mater. Sci. Eng. A, 2005, vol. 405, pp. 339-49.10.1016/j.msea.2005.06.002 ↗
26. K. Fujiyama, K. Mori, D. Kaneko, H. Kimachi, T. Saito, R. Ishii, and T. Hino: Int. J. Pressure Vessels Piping, 2009, vol. 86, pp. 570-77.10.1016/j.ijpvp.2009.04.011 ↗
27. D.J. Child, G.D. West, and R.C. Thomson: Acta Mater., 2011, vol. 59, pp. 4825-34.10.1016/j.actamat.2011.04.025 ↗
28. D.P. Field, K.R. Magid, I.N. Mastorakos, J.N. Florando, D.H. Lassila, and J.W. Morris: Philos. Mag., 2010, vol. 90, pp. 1451-64.10.1080/14786430903397297 ↗
29. S. Scheriau, and R. Pippan: Mater. Sci. Eng. A, 2008, vol. 493, pp. 48-52.10.1016/j.msea.2007.08.092 ↗
30. A.J. Hayter: Probability and Statistics for Engineers and Scientists, Brooks/Cole Centage Learning, Boston, 2012, pp. 199–202.
31. S. Zaefferer: Cryst. Res. Technol., 2011, vol. 46, pp. 607-28.10.1002/crat.201100125 ↗
32. D. Dingley: J. Microsc., 2004, vol. 213, pp. 214-24.10.1111/j.0022-2720.2004.01321.x ↗
33. O.V. Mishin, A. Godfrey, and D.J. Jensen: in Electron Backscatter Diffraction in Materials Science, A.J. Schwartz, M. Kumar, and B.L. Adams, eds., Springer Science, New York, 2009, pp. 263–75.10.1007/978-0-387-88136-2_19 ↗
34. H. Mirzadeh, J.M. Cabrera, A. Najafizadeh, and P.R. Calvillo: Mater. Sci. Eng. A, 2012, vol. 538, pp. 236-45.10.1016/j.msea.2012.01.037 ↗
35. F.J. Humphreys, Y. Huang, I. Brough, and C. Harris: J. Microsc., 1999, vol. 195, pp. 212-16.10.1046/j.1365-2818.1999.00579.x ↗
36. I. Brough, P.S. Bate, and F.J. Humphreys: Mater. Sci. Technol., 2006, vol. 22, pp. 1279-86.10.1179/174328406X130902 ↗
37. A. Agresti: An Introduction to Categorical Data Analysis, Wiley, New Jersey, 2007, pp. 35–36.10.1002/0470114754 ↗
38. Z. Govindarajulu: Statistical Techniques in Bioassay, S. Karger AG, Basel, 2001, pp. 197–99.10.1159/isbn.978-3-318-00617-9 ↗
39. T.S. Byun, N. Hashimoto, and K. Farrell: Acta Mater., 2004, vol. 52, pp. 3889-99.10.1016/j.actamat.2004.05.003 ↗
40. S. Venugopal, S.L. Mannan, and Y.V.R.K. Prasad: J. Nucl. Mater., 1995, vol. 227, pp. 1-10.10.1016/0022-3115(95)00154-9 ↗
41. K.G. Samuel, S.L. Mannan, and P. Rodriguez: Acta Metall., 1988, vol. 36, pp. 2323-27.10.1016/0001-6160(88)90331-8 ↗
42. E.I. Samuel, B.K. Choudhary, and K.B.S. Rao: Scr. Mater., 2002, vol. 46, pp. 507-12.10.1016/S1359-6462(02)00023-4 ↗
43. C.G. Shastry, M.D. Mathew, K.B.S. Rao, and S.D. Pathak: Mater. Sci. Technol., 2007, vol. 23, pp. 1215-22.10.1179/174328407X226581 ↗
44. P. Rodriguez: Bull. Mater. Sci., 1984, vol. 6, pp. 653-63.10.1007/BF02743993 ↗
45. M.T. Nogueira, and M.A. Fortes: Scr. Metall., 1984, vol. 18, pp. 505-08.10.1016/0036-9748(84)90430-7 ↗
46. B.P. Kashyap, K. McTaggart, and K. Tangri: Philos. Mag., 1988, vol. 57, pp. 97-114.10.1080/01418618808204501 ↗
47. B.P. Kashyap, and K. Tangri: Acta Metall. Mater., 1995, vol. 43, pp. 3971-81.10.1016/0956-7151(95)00110-H ↗
48. D.A. Hughes, Q. Liu, D.C. Chrzan, and N. Hansen: Acta Mater., 1997, vol. 45, pp. 105-12.10.1016/S1359-6454(96)00153-X ↗
49. W. Pantleon: J. Mater. Res., 2002, vol. 17, pp. 2433-41.10.1557/JMR.2002.0355 ↗
50. D.A. Hughes, D.C. Chrzan, Q. Liu, and N. Hansen: Phys. Rev. Lett., 1998, vol. 81, pp. 4664-67.10.1103/PhysRevLett.81.4664 ↗
51. B. Bay, N. Hansen, D.A. Hughes, and D. Kuhlmann-Wilsdorf: Acta Metall. Mater., 1992, vol. 40, pp. 205-19.10.1016/0956-7151(92)90296-Q ↗
52. W. Pantleon, and N. Hansen: Acta Mater., 2001, vol. 49, pp. 1479-93.10.1016/S1359-6454(01)00027-1 ↗
53. M. Janecek, and K. Tangri: J. Mater. Sci., 1995, vol. 30, pp. 3820-26.10.1007/BF01153940 ↗
54. K.J. Kurzydlowski, K.J. McTaggart, and K. Tangri: Philos. Mag., 1990, vol. 61, pp. 61-83.10.1080/01418619008235558 ↗
55. C.C. Merriman, D.P. Field, and P. Trivedi: Acta Mater., 2008, vol. 1, pp. 153-62.
56. P.G. Gottschalk, and J.R. Dunn: Anal. Biochem., 2005, vol. 343, pp. 54-65.10.1016/j.ab.2005.04.035 ↗
57. M. Predeleanu and P. Gilormini: Advanced Methods in Materials Processing Defects, Elsevier Science B.V, Amsterdam, 1997, pp. 100–02.
58. O.V. Rofman, P.S. Bate, I. Brough, and F.J. Humphreys: J. Microsc., 2009, vol. 233, pp. 432-41.10.1111/j.1365-2818.2009.03131.x ↗
59. H.J. Frost and M.F. Ashby: Deformation-Mechanism Maps: The Plasticity and Creep of Metals and Ceramics, Elsevier Science & Technology, London, 1982, p. 60.
60. R.W. Evans and B. Wilshire: Introduction to Creep, The Institute of Materials, London, 1993, pp. 38–49.