Correlation Between Intercritical Heat-Affected Zone and Type IV Creep Damage Zone in Grade 91 Steel
Source abstract
Abstract
A soft zone in Cr-Mo steel weldments has been reported to accompany the infamous Type IV cracking, the highly localized creep damage in the heat-affected zone of creep-resistant steels. However, the microstructural features and formation mechanism of this soft zone are not well understood. In this study, using microhardness profiling and microstructural verification, the initial soft zone in the as-welded condition was identified to be located in the intercritical heat-affected zone of P91 steel weldments. It has a mixed structure, consisting of Cr-rich re-austenitized prior austenite grains and fine Cr-depleted, tempered martensite grains retained from the base metal. The presence of these further-tempered retained grains, originating from the base metal, is directly responsible for the hardness reduction of the identified soft zone in the as-welded condition. The identified soft zone exhibits a high location consistency at three thermal stages. Local chemistry analysis and thermodynamic calculation show that the lower chromium concentrations inside these retained grains thermodynamically decrease their potentials for austenitic transformation during welding. Heterogeneous grain growth is observed in the soft zone during postweld heat treatment. The mismatch of strengths between the weak Cr-depleted grains and strong Cr-rich grains enhances the creep damage. Local deformation of the weaker Cr-depleted grains accelerates the formation of creep cavities.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. K. Easterling: in Introduction to the Physical Metallurgy of Welding, Butterworth-Heimemann Ltd, Oxford, 1992.
2. F. Abe, T.U. Kern and R. Viswanathan: in Creep-Resistant Steels, Woodhead Publishing, Cambridge, 2008.10.1533/9781845694012 ↗
3. J. Francis, W. Mazur, and H. Bhadeshia: Mater. Sci. Tech., 2006, vol. 22, pp. 1387–95.10.1179/174328406X148778 ↗
4. S.A. David, J.A. Siefert and Z. Feng: Sci. Technol. Welding J., 2013, vol. 18, pp. 631–51.10.1179/1362171813Y.0000000152 ↗
5. P. Mayr: Doctoral thesis, Graz University of Technology, 2007.
6. T. Watanabe, M. Tabuchi, M. Yamazaki, H. Hongo and T. Tanabe: Int. J. Pres. Ves. Piping, 2006, vol. 83, pp. 63–71.10.1016/j.ijpvp.2005.09.004 ↗
7. J. Hald: Int. J. Pres. Ves. Piping, 2008, vol. 85, pp. 30–37.10.1016/j.ijpvp.2007.06.010 ↗
8. D. Abson and J. Rothwell: Int. Mater. Rev., 2013, vol. 58, pp. 437–73.10.1179/1743280412Y.0000000016 ↗
9. F. Abe: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 5610–25.10.1007/s11661-015-3144-5 ↗
10. S. Albert, M. Matsui, T. Watanabe, H. Hongo, K. Kubo and M. Tabuchi: Int. J. Pres. Ves. Piping, 2003, vol. 80, pp. 405–13.10.1016/S0308-0161(03)00072-3 ↗
11. J. Parker and S. Brett: Int. J. Pres. Ves. Piping, 2013, vol. 111-112, pp. 82-88.10.1016/j.ijpvp.2013.05.003 ↗
12. K. Laha, K. Chandravathi, P. Parameswaran, K. Rao and S. Mannan: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 58–68.10.1007/s11661-006-9050-0 ↗
13. J. Parker: Mater. Sci. Eng. A, 2013, vol. 578, pp. 430–37.10.1016/j.msea.2013.04.045 ↗
14. J. Parker and G. Stratford: Int. J. Pres. Ves. Piping, 1996, vol. 68, pp. 135–43.10.1016/0308-0161(94)00046-8 ↗
15. K. Maruyama, K. Sawada and J. Koike: ISIJ Int., 2001, vol. 41, pp. 641–53.10.2355/isijinternational.41.641 ↗
16. F. Abe: Sci. Tech. Adv. Mater., 2008, vol. 09, pp. 013002.10.1088/1468-6996/9/1/013002 ↗
17. Y. Liu, S. Tsukamoto, K. Sawada and F. Abe: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 1306–14.10.1007/s11661-013-2072-5 ↗
18. C. Coussement, A. Dhooge, M. de Witte, R. Dobbelaere and E. van der Donckt: Int. J. Pres. Ves. Piping, 1991, vol. 45, pp. 163–78.10.1016/0308-0161(91)90090-O ↗
19. M. Sireesha, Shaju K. Albert, and S. Sundaresan: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1495–06.10.1007/s11661-005-0241-x ↗
20. K.K. Coleman and W. F. Newell: Welding J., 2007, vol. 86, pp. 29–33.
21. L. Li, B. Silwal and A. Deceuster: Int. J. Pres. Ves. Piping, 2016, vol. 146, pp. 95–103.10.1016/j.ijpvp.2016.07.008 ↗
22. Y. Wang, R. Kannan and L. Li: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 5680–84.10.1007/s11661-016-3736-8 ↗
23. S. Morito, H. Tanaka, R. Konishi, T. Furuhara and T. Maki: Acta Mater., 2003, vol. 51, pp. 1789–99.10.1016/S1359-6454(02)00577-3 ↗
24. S. Morito, X. Huang, T. Furuhara, T. Maki and N. Hansen: Acta Mater., 2006, vol. 54, pp. 5323–31.10.1016/j.actamat.2006.07.009 ↗
25. S. Morito, H. Saito, T. Ogawa, T. Furuhara and T. Maki: ISIJ Int., 2005, vol. 45, pp. 91–94.10.2355/isijinternational.45.91 ↗
26. Y. Wang, R. Kannan, and L. Li: Mater. Charact., 2016, vol. 118, pp. 225–34.10.1016/j.matchar.2016.05.024 ↗
27. Y. Wang and L. Li: Welding J., 2016, vol. 95, pp. 27–36.
28. Y. Zhang, P. H. Shipway and F. Boue-Bigne: Sci. Technol. Welding J., 2009, vol. 14, pp. 542–48.10.1179/136217109X441191 ↗
29. K. Sawada, T. Hara, M. Tabuchi, K. Kimura and K. Kubushiro: Mater. Charact., 2015, vol. 101, pp. 106–13.10.1016/j.matchar.2015.01.013 ↗
30. G. Kirchner, T. Nishizawa and B. Uhrenius: Metall. Trans., 1973, vol. 4, pp. 167–74.10.1007/BF02649616 ↗
31. J. B. Austin and R. H. H. Pierce Jr.: AIME Trans., 1935, vol. 116, pp. 289–308.