The Effect of a Laser Beam on Chip Formation during Machining of Ti6Al4V Alloy
Source abstract
Abstract
The effect of the laser beam on chip formation when machining Ti6Al4V alloy has been investigated at different cutting speeds and laser powers. The characteristics of the segmented chip produced by laser-assisted machining (LAM) in terms of the tooth depth and tooth spacing were strongly dependent on the cutting speed and laser power. Two types of segmented chip formation processes were observed, one at low and the other at high cutting speeds with a continuous chip occurring between these two types of segmented chips. The critical cutting speed at which the transition from the sharp, segmented chip to the continuous chip occurred increased with laser power. To obtain the continuous chip, plastic deformation at the shear zone to match the deformation strain introduced by the cutting tool is required. This can be achieved by laser heating the material in front of the cutting tool. A physical model is proposed to explain qualitatively the chip segmentation in conventional machining and the continuous chip transition at high cutting speed with the application of a laser beam.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Additive Manufacturing Materials and Processes · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. M. Bäker, J. Rösler, and C. Siemers: Trans. ASME J. Manuf. Sci. Eng., 2002, vol. 124, pp. 485–88.10.1115/1.1459469 ↗
2. A.E. Bayoumi and J.Q. Xie: Mater. Sci. Eng. A, 1995, vol. 190, pp. 173–80.10.1016/0921-5093(94)09595-N ↗
3. M. Cotterell and G. Byrne: Int. J. Nano Biomater., 2007, vol. 1, pp. 65–75.10.1504/IJNBM.2007.016520 ↗
4. R. Komanduri: Wear, 1982, vol. 76, pp. 15–34.10.1016/0043-1648(82)90113-2 ↗
5. R. Komanduri and B.F.V. Turkovich: Wear, 1981, vol. 69, pp. 179–88.10.1016/0043-1648(81)90242-8 ↗
6. T. Obikawa and E. Usui: Trans. ASME J. Manuf. Sci. Eng., 1996, vol. 118, pp. 208–15.10.1115/1.2831013 ↗
7. J.D.P. Velásquez, B. Bolle, P. Chevrier, G. Geandier, and A. Tidu: Mater. Sci. Eng. A, 2007, vols. 452–453, pp. 469–74.10.1016/j.msea.2006.10.090 ↗
8. R. Komanduri and Z.-B. Hou: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2995–10.10.1007/s11661-002-0284-1 ↗
9. J. Barry, G. Byrne, and D. Lennon: Int. J. Mach. Tool Manuf., 2001, vol. 41, pp. 1055–70.10.1016/S0890-6955(00)00096-1 ↗
10. M.C. Shaw and A. Vyas: Ann. ClRP, 1998, vol. 47, pp. 77–82.10.1016/S0007-8506(07)62789-9 ↗
11. A. Vyas and M.C. Shaw: Trans. ASME J. Manuf. Sci. Eng., 1999, vol. 211, pp. 163–72.10.1115/1.2831200 ↗
12. P. Dumitrescu, P. Koshy, J. Stenekes, and M.A. Elbestawi: Int. J. Mach. Tool Manuf., 2006, vol. 46, pp. 2009–16.10.1016/j.ijmachtools.2006.01.005 ↗
13. S. Rajagopal, D.J. Plankenhorn, and V.L. Hill: J. Appl. Metalworking, 1982, vol. 2, pp. 170–84.10.1007/BF02834035 ↗
14. S. Sun, J. Harris, and M. Brandt: Adv. Eng. Mater., 2008, vol. 10, pp. 565–72.10.1002/adem.200700349 ↗
15. B. Lesourd, F.L. Maître, and T. Thomas: Manuf. Sys., 1995, vol. 24, pp. 279–86.
16. M. Anderson, R. Patwa, and Y.C. Shin: Int. J. Mach. Tool Manuf., 2006, vol. 46, pp. 1879–91.10.1016/j.ijmachtools.2005.11.005 ↗
17. J.C. Rozzi, F.P. Incropera, and Y.C. Shin: Int. J. Heat Mass Transfer, 2000, vol. 43, pp. 1425–37.10.1016/S0017-9310(99)00219-7 ↗
18. J.C. Rozzi, F.E. Pfefferkorn, F.P. Incropera, and Y.C. Shin: Int. J. Heat Mass Transfer, 2000, vol. 43, pp. 1409–24.10.1016/S0017-9310(99)00217-3 ↗
19. K.N. Vonatsos and D.I. Pantelis: Appl. Phys. A, 2005, vol. 80, pp. 885–89.10.1007/s00339-003-2339-6 ↗
20. D.I. Pantelis and K.N. Vonatsos: Appl. Phys. A, 1998, vol. 67, pp. 435–39.10.1007/s003390050800 ↗
21. S. Sun, M. Brandt, and M.S. Dargusch: Int. J. Mach. Tool Manuf., 2009, vol., pp. 561–68.10.1016/j.ijmachtools.2009.02.008 ↗
22. M.C. Shaw: Metal Cutting Principles, 2nd ed., Oxford University Press, New York, NY, 2005, p. 22.
23. M.R. Shankar, B.C. Rao, S. Lee, S. Chandrasekar, A.H. King, and W.D. Compton: Acta Mater., 2006, vol. 54, pp. 3691–3700.10.1016/j.actamat.2006.03.056 ↗
24. D.R. Chichili, K.T. Ramesh, and K.J. Hemker: Acta Mater., 1998, vol. 46, pp. 1025–43.10.1016/S1359-6454(97)00287-5 ↗
25. K.T. Ramesh: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 927–35.10.1007/s11661-002-0162-x ↗
26. G.L. Wulf: Int. J. Mech. Sci., 1979, vol. 21, pp. 713–18.10.1016/0020-7403(79)90051-1 ↗
27. P. Follansbee and G.T. Gray: Metall. Trans. A, 1989, vol. 20A, pp. 863–74.10.1007/BF02651653 ↗
28. W.-S. Lee and C.-F. Lin: Mater. Sci. Eng. A, 1998, vol. 241, pp. 48–59.10.1016/S0921-5093(97)00471-1 ↗