journal article·2012-01

Influence of Aging Parameters on the Tensile Properties and Quality Index of Al-9 Pct Si-1.8 Pct Cu-0.5 Pct Mg 354-Type Casting Alloys

H. R. Ammar, A. M. Samuel, F. H. Samuel, E. Simielli, G. K. Sigworth, J. C. Lin

Publisher page

Abstract

The current study was carried out with a view to investigating the influence of age-hardening parameters, aging temperature and time, on the tensile properties and quality indices of a high-strength Al-9 pct Si casting alloy, namely, 354-Al-9 pct Si-1.8 pct Cu-0.5 pct Mg. Quality charts were used as an evaluation tool for selecting the optimum conditions to be applied, in practice, in order to develop high strength and optimum quality in 354 casting alloy. Aging at a low temperature of 428 K (155 °C) was observed to produce the greatest strength and optimum quality in the 354-type castings compared to aging at higher temperatures. The peak strength observed for 354 alloy may be attained after shorter aging times on the condition that the aging temperature is increased. The aging times required for reaching peak strength in 354 alloys are 72 hours, 40 hours, 8 hours, 1 hour, and 15 minutes at aging temperatures of 428 K, 443 K, 468 K, 493 K, and 518 K (155 °C, 170 °C, 195 °C, 220 °C, and 245 °C), respectively. Aging treatment at higher temperatures is accompanied by a reduction in the tensile properties and quality index values of the castings; however, it also introduces the possibility of a significant economical strategy for minimizing the time and the cost of this same treatment. Aging treatment at a lower temperature of 428 K (155 °C) produces fine and dense precipitates displaying smaller interparticle spacing, while at higher aging temperatures, such as 518 K (245 °C), the precipitates are coarser in size, less dense, and more widely dispersed. The quality charts developed in the course of the current research facilitate the interpretation and evaluation of the tensile properties of the 354 alloy. Such charts provide a logical evaluation tool, from the metallurgical point of view, for an accurate prediction of the influence of aging parameters studied on the properties of the alloys. Depending on the required level of tensile properties and based on the quality charts developed, it is possible to make a rigorous selection as to the most suitable aging parameters to be applied to the 354 alloy so as to obtain the best possible cost-effective compromise between alloy strength and quality.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. R.C. Lemon and C.R. Howle: AFS Trans., 1963, vol. 70, pp. 465–70.
2. J.G. Kaufman and E.L. Rooy: Aluminum Alloy Castings: Properties, Processing, and Applications, ASM INTERNATIONAL, Materials Park, OH, 2004, pp. 31–32 and 69–131.10.31399/asm.tb.aacppa.9781627083355 ↗
3. J. Man, L. Jing, and S.G. Jie: J. Alloys Compd., 2007, vol. 437, pp. 146–50.10.1016/j.jallcom.2006.07.113 ↗
4. M. Murayama, K. Hono, M. Saga, and M. Kikuchi: Mater. Sci. Eng. A, 1998, vol. 250, pp. 127–32.10.1016/S0921-5093(98)00548-6 ↗
5. L. Zhen, W.D. Fei, S.B. Kang, and H.W. Kim: J. Mater. Sci., 1997, vol. 32, pp. 1895–1902.10.1023/A:1018569226499 ↗
6. W.F. Miao and D.E. Laughlin: Scripta Mater., 1999, vol. 40 (7), pp. 873–78.10.1016/S1359-6462(99)00046-9 ↗
7. S.J. Andersen, C.D. Marioara, R. Vissers, A. Frøseth, and H.W. Zandbergen: Mater. Sci. Eng. A, 2007, vol. 444, pp. 157–69.10.1016/j.msea.2006.08.084 ↗
8. C.D. Marioara, S.J. Andersen, J. Jansen, and H.W. Zandbergen: Acta Mater., 2001, vol. 49, pp. 321–28.10.1016/S1359-6454(00)00302-5 ↗
9. R. Vissers, M.A. Van Huis, J. Jansen, H.W. Zandbergen, C.D. Marioara, and S.J. Andersen: Acta Mater., 2007, vol. 55, pp. 3815–23.10.1016/j.actamat.2007.02.032 ↗
10. S.J. Andersen, C.D. Marioara, A. Frøseth, R. Vissers, and H.W. Zandbergen: Mater. Sci. Eng. A, 2005, vol. 390, pp. 127–38.10.1016/j.msea.2004.09.019 ↗
11. D.G. Eskin: J. Mater. Sci., 2003, vol. 38, pp. 279–90.10.1023/A:1021109514892 ↗
12. S.K. Son, M. Takeda, M. Mitome, Y. Bando, and T. Endo: Mater. Lett., 2005, vol. 75, pp. 629–32.10.1016/j.matlet.2004.10.058 ↗
13. S.P. Ringer and K. Hono: Mater. Charact., 2000, vol. 44, pp. 101–31.10.1016/S1044-5803(99)00051-0 ↗
14. G.E. Totten and D.S. Mackenzie: Handbook of Aluminum, vol. 1: Physical Metallurgy and Processes, Marcel Dekker, New York, NY, 2003, pp. 272–84.10.1201/9780203912591 ↗
15. S.C. Wang, M.J. Starink, and N. Gao: Scripta Mater., 2006, vol. 54, pp. 287–91.10.1016/j.scriptamat.2005.09.010 ↗
16. P. Ratchev, B. Verlinden, P. De Smet, and P. Van Houtte: Scripta Mater., 1998, vol. 38 (8), pp. 1195–1201.10.1016/S1359-6462(98)00024-4 ↗
17. A. Charai, T. Walther, C. Alfonso, A.-M. Zahra, and C.Y. Zahra: Acta Mater., 2000, vol. 48, pp. 2751–64.10.1016/S1359-6454(99)00422-X ↗
18. P. Ratchev, B. Verlinden, P. De Smet, and P. Van Houtte: Acta Mater., 1998, vol. 46 (10), pp. 3523–33.10.1016/S1359-6454(98)00033-0 ↗
19. S.P. Ringer, B.T. Sofyan, K.S. Prasad, and G.C. Quan: Acta Mater., 2008, vol. 56, pp. 2147–60.10.1016/j.actamat.2007.12.046 ↗
20. D.J. Chakrabarti and D.E. Laughlin: Prog. Mater. Sci., 2004, vol. 49, pp. 389–410.10.1016/S0079-6425(03)00031-8 ↗
21. C. Cayron and P.A. Buffat: Acta Mater., 2000, vol. 48, pp. 2639–53.10.1016/S1359-6454(00)00057-4 ↗
22. C. Wolverton: Acta Mater., 2001, vol. 49, pp. 3129–42.10.1016/S1359-6454(01)00229-4 ↗
23. C. Cayron, L. Sagalowicz, O. Beffort, and P.A. Buffat: Philos. Mag. A, 1999, vol. 79 (11), pp. 2833–51.10.1080/01418619908212027 ↗
24. M. Drouzy, S. Jacob, and M. Richard: AFS Int. Cast Met. J., 1980, vol. 5, pp. 43–50.
25. S. Jacob: AFS Trans., 2000, vol. 108, pp. 811–18.
26. Annual Book of ASTM Standards, Section 2: Nonferrous Metal Products, Aluminum and Magnesium Alloys, ASTM, Philadelphia, PA, 2004, vol. 02.02, B108-03a, pp. 82–83.
27. H.R. Ammar: Ph.D. Thesis, University of Quebec, Quebec, Canada, 2010, pp. 74–150.
28. R.N. Lumley, I.J. Polmear, and P.R. Curtis: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 1716–26.10.1007/s11661-009-9836-y ↗
29. G. Wang, X. Bian, X. Liu, and J. Zhang: J. Mater. Sci., 2004, vol. 39, pp. 2535–37.10.1023/B:JMSC.0000020022.19854.ac ↗
30. S. Esmaeili, X. Wang, D.J. Lloyd, and W.J. Poole: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 751–63.
31. S.K. Chaudhury and D. Apelian: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2295–2311.10.1007/BF02586148 ↗
32. R.N. Lumley, R.G. O’Donnell, D.R. Gunasegaram, and M. Givord: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 2564–74.10.1007/s11661-007-9285-4 ↗
33. H.G. Kang, M. Kida, H. Miyahara, and K. Ogi: AFS Trans., 1999, vol. 107, pp. 507–15.
34. R.X. Li, R.D. Li, Y.H. Zhao, L.Z. He, C.X. Li, H.R. Guan, and Z.Q. Hu: Mater. Lett., 2004, vol. 58, pp. 2096–2101.10.1016/j.matlet.2003.12.027 ↗
35. W. Reif, J. Dutkiewicz, R. Ciach, S. Yu, and J. Krol: Mater. Sci. Eng. A, 1997, vols. A234–A236, pp. 165–68.10.1016/S0921-5093(97)00181-0 ↗
36. S. Zafar, N. Ikram, M.A. Shaikh, and K.A Shoaib: J. Mater. Sci., 1990, vol. 25 (5), pp. 2595–97.10.1007/BF00638064 ↗
37. N. Ryum and O. Hunderi: Encycl. Mater. Sci. Technol., 2008, pp. 7826–35.
38. M. Kahlweit: Adv. Coll. Interface Sci., 1975, vol. 5 (1), pp. 1–35.10.1016/0001-8686(75)85001-9 ↗
39. T. Gladman: Mater. Sci. Technol., 1999, vol. 15 (1), pp. 30–36.10.1179/026708399773002782 ↗
40. M. Warmuzek: Aluminum-Silicon Casting Alloys: Atlas of Microfractographs, ASM INTERNATIONAL, Materials Park, OH, 2004, pp. 18–25.
41. G.E. Dieter: Mechanical Metallurgy: Third Edition, McGraw-Hill, New York, NY, 1986, pp. 254–56 and 262–65.