The Effectiveness of Surface Coatings on Preventing Interfacial Reaction During Ultrasonic Welding of Aluminum to Magnesium
Source abstract
Abstract
Abstract High power ultrasonic spot welding (USW) is a solid-state joining process that is advantageous for welding difficult dissimilar material couples, like magnesium to aluminum. USW is also a useful technique for testing methods of controlling interfacial reaction in welding as the interface is not greatly displaced by the process. However, the high strain rate deformation in USW has been found to accelerate intermetallic compound (IMC) formation and a thick Al12Mg17 and Al3Mg2 reaction layer forms after relatively short welding times. In this work, we have investigated the potential of two approaches for reducing the IMC reaction rate in dissimilar Al-Mg ultrasonic welds, both involving coatings on the Mg sheet surface to (i) separate the join line from the weld interface, using a 100-μm-thick Al cold spray coating, and (ii) provide a diffusion barrier layer, using a thin manganese physical vapor deposition (PVD) coating. Both methods were found to reduce the level of reaction and increase the failure energy of the welds, but their effectiveness was limited due to issues with coating attachment and survivability during the welding cycle. The effect of the coatings on the joint’s interface microstructure, and the fracture behavior have been investigated in detail. Kinetic modeling has been used to show that the benefit of the cold spray coating can be attributed to the reaction rate reverting to that expected under static conditions. This reduces the IMC growth rate by over 50 pct because at the weld line, the high strain rate dynamic deformation in USW normally enhances diffusion through the IMC layer. In comparison, the thin PVD barrier coating was found to rapidly break up early in USW and become dispersed throughout the deformation layer reducing its effectiveness.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. D. Carle, and G. Blount (1999) Mater. Des. 20:267–72.10.1016/S0261-3069(99)00003-5 ↗
2. A. Jambor and M. Beyer: Mater. Des., 1997, vol.18, pp. 203–09.10.1016/S0261-3069(97)00049-6 ↗
3. X. Cui, S. Wangand S.J. Hu: Mater. Des., 2008, vol. 29, pp. 381–87.10.1016/j.matdes.2007.01.024 ↗
4. R. Borrisutthekul, Y. Miyashita and Y. Mutoh: Sci. Technol. Adv. Mater., 2005, vol. 6, pp. 199–204.10.1016/j.stam.2004.11.014 ↗
5. P. Venkateswaran, Z.-H. Xu, X. Liand, A.P. Reynolds (2009) J. Mater. Sci. Eng. 44:4140–47.
6. V. Firouzdor and S. Kou: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 2914–35.10.1007/s11661-010-0340-1 ↗
7. D.-H. Choi, B.-W. Ahn, C.-Y. Lee, Y.-M. Yeon, K. Song and S.-B. Jung: Intermetallics, 2011, vol. 19, pp. 125–30.10.1016/j.intermet.2010.08.030 ↗
8. J. Yan, Z. Xu, Z. Li, L. Li and S. Yang: Scripta Mater., 2005, vol. 53, pp. 585–89.10.1016/j.scriptamat.2005.04.022 ↗
9. A. Gerlich, P. Su and T. H. North (2005) Sci. Technol. Weld. Join. 10:647–52.10.1179/174329305X48383 ↗
10. T.A. Barnes, I.R. Pashby (2000) J. Mater. Process. Technol. 99 (1–3):62–71.10.1016/S0924-0136(99)00367-2 ↗
11. T.A. Barnes, I.R. and Pashby (2000) J. Mater. Process. Technol. 99 (1–3):72–79.10.1016/S0924-0136(99)00361-1 ↗
12. H.C.P. Daniels (1965) Ultrasonics 3:190–96.10.1016/0041-624X(65)90169-1 ↗
13. Y. Gao and C. Doumanidis (2002) ASME J. Manuf. Sci. Eng., 124 (2):426–34.10.1115/1.1459082 ↗
14. R. Jahn, R. Cooper and D. Wilkosz: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 570–83.10.1007/s11661-006-9087-0 ↗
15. D. Bakavos, and P.B. Prangnell: Mater. Sci. Eng. A, 2010, vol.527, pp. 6320–34.10.1016/j.msea.2010.06.038 ↗
16. J.L. Harthoorn: Doctoral Thesis, De Technische Hogeschool Eindhoven, 1978.
17. Y-R. Jeng and J-H. Horng (2001) ASME J. Tribol., 123:725–31.10.1115/1.1352744 ↗
18. Y.-C. Chen, D. Bakavos and P.B. Prangnell (2012) Acta Mater 60:2816–28.10.1016/j.actamat.2012.01.047 ↗
19. A. Panteli, J.D. Robson, I.Brough and P.B. Prangnell (2012) Mater. Sci. Eng. A 556:31–42.10.1016/j.msea.2012.06.055 ↗
20. E.M. TanguepNjiokep, M. Salamon and H. Mehrer (2001) Defect Diffus. Forum, 194–199:1581–86.10.4028/www.scientific.net/DDF.194-199.1581 ↗
21. V. Rothova and J. Cermak: Proc 15th Int. Metallurgical & Material Conference, Czech Republic, Metal, 2006, pp. 1–8.
22. J.L. Murray: Binary Alloy Phase Diagrams, 2nd ed., T.B. Massalski, ed., ASM International, Metals Park, OH, vol. 1, 1990, pp. 169–71.
23. Y.S. Sato, S.H.C. Park, M. Michiuchi and H. Kokawa (2004) Scripta Mater 50:1233–36.10.1016/j.scriptamat.2004.02.002 ↗
24. D. Dietrich, D. Nickel, M. Krause, T. Lampke, M.P. Coleman and V. Randle: J. Mater. Sci., 2011, vol. 46, pp. 357–64.10.1007/s10853-010-4841-5 ↗
25. I.E. Gundaz, T. Ando, E. Shattuck, P.Y. Wong and C.C. Doumanidis: Scripta Mater., 2005, vol. 52, pp. 939–43.10.1016/j.scriptamat.2004.12.015 ↗
26. R.W. Richards, R.D. Jones, P.D. Clements and H. Clarke: Int. Mater. Rev., 1994, vol.39, pp. 191–209.10.1179/imr.1994.39.5.191 ↗
27. L.M. Zhao and Z.D. Zhang (2008) Scripta Mater. 58:283–86.10.1016/j.scriptamat.2007.10.006 ↗
28. L. Liu, X. Liu and S. Liu (2006) Scripta Mater. 55:383–86.10.1016/j.scriptamat.2006.04.025 ↗
29. M. Asgar-Khan and M. Medraj: Proc. Materials Science and Technology (MS&T), October 5–9, 2008, Pittsburgh, PA, pp. 1029–41.
30. W.B. Choi, L. Li, V. Luzin, R. Neiser, T. Gnäupel-Herold, H.J. Prask, S. Sampath and A. Gouldstone (2007) Acta Mater. 55:857–66.10.1016/j.actamat.2006.09.006 ↗
31. S. Elangovan, S. Semeer and K. Prakasan (2009) J. Mater. Process. Technol. 209:1143–50.10.1016/j.jmatprotec.2008.03.032 ↗
32. J.D. Robson, A. Panteli, N. Iqbal and P.B. Prangnell (2012) Sci. Technol. Weld. Join. 17:447–53.10.1179/1362171812Y.0000000032 ↗
33. J. Philibert (1994) Mater. Sci. Forum 155–156:15–30.10.4028/www.scientific.net/MSF.155-156.15 ↗
34. S. Fujikawa and K. Hirano (1977) Mater. Sci. Eng. A 27A:25–33.10.1016/0025-5416(77)90190-2 ↗
35. W. Lauwerens, A. De Boeckb, M. Thijs, S. Claessens, M. Van Stappen and P. Steenackers (2001) Surf. Coat. Technol. 146–147: 27–32.10.1016/S0257-8972(01)01468-2 ↗
36. M. Reffass, C. Berziou, C. Rébéré, A. Billard and J. Creus (2010) Corros. Sci. 52:3615–23.10.1016/j.corsci.2010.07.008 ↗