journal article·2003-02

Influence of thermomechanical treatments on the microstructure and mechanical properties of HSLA-100 steel plates

S. K. Dhua, D. Mukerjee, D. S. Sarma

Publisher page

Abstract

The influence of thermomechanical treatment (TMT), i.e., controlled rolling and direct quenching, as a function of rolling temperature and deformation on the microstructure and mechanical properties of HSLA-100 steel have been studied. The optical microstructure of the direct quenched (DQ) and tempered steel rooled at lower temperatures (800 °C and 900 °C) showed elongated and deformed grains, whereas complete equiaxed grains were visible after rolling at 1000 °C. The transmission electron microscope (TEM) microstructure of the 800 °C rooled DQ steel showed shorter, irregular, and closer martensite laths with extremely fine Cu and Nb(C,N) precipitates after tempering at 450 °C. The precipitates coarsened somewhat after tempering at 650 °C; the degree of coarsening was, however, less compared to that of the reheat-quenched (RQ) and tempered steel, indicating that the DQ steel was slightly more resistant to tempering. Similar to the RQ steel, at a 450 °C tempering condition, the DQ steel exhibited peak strength with extremely poor impact toughness. After tempering at 650 °C, the toughness of the DQ steel improved significantly, but at the expense of its strength. In general, the strength of the DQ and tempered steel was good and comparable to that of the RQ and tempered steel, although, its impact toughness was marginally less than the latter. The optimum combination of strength and toughness in the DQ steels was achieved after 900 °C rolling with 50 pct deformation, followed by direct quenching and tempering at 650 °C (yield strength (YS)=903 MPa, ultimate tensile strength (UTS)=928 MPa, and Charpy V-notch (CVN) strength=143 J at −85 °C).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. R.J. Jesseman and G.J. Murphy: J. Heat Treating, 1984, vol. 3, pp. 228–36.10.1007/BF02833265 ↗
2. G.E. Hicho, C.H. Brady, L.C. Smith, and R.J. Fields: J. Heat Treating, 1987, vol. 5, pp. 7–19.10.1007/BF02831616 ↗
3. Takashi Abe, Masayoshi Kurihara, and Histoshi Tagawa: Trans. Iron Steel Inst. Jpn., 1987, vol. 27, pp. 478–84.10.2355/isijinternational1966.27.478 ↗
4. A.D. Wilson: J. Met., 1987, vol. 29, pp. 36–38.
5. G.E. Hicho and R.J. Fields: J. Heat Treating, 1988, vol. 6 (2), pp. 77–85.10.1007/BF02833108 ↗
6. A.D. Wilson, E.G. Hamburg, D.J. Colvin, S.W. Thompson, and G. Krauss: Proc. Int. Conf. on Microalloyed HSLA Steel, Microalloyings’ 88, 1988, ASM INTERNATIONAL, Metals Park, OH, pp. 259–75.
7. S.W. Thompson, D.J. Colvin, and G. Krauss: Scripta Metall., 1988, vol. 22, pp. 1069–74.10.1016/S0036-9748(88)80105-4 ↗
8. S.W. Thompson, D.J. Colvin, and G. Krauss: Metall. Trans. A, 1990, vol. 21A, pp. 1493–1507.10.1007/BF02672564 ↗
9. S.S. Banadkouki Ghasemi, D. Yu, and D.P. Dunne: Iron Steel Inst. Jpn. Int., 1996, vol. 36, pp. 61–67.10.2355/isijinternational.36.61 ↗
10. S.W. Thompson, D.J. Kolvin, and G. Krauss: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1557–71.10.1007/BF02649815 ↗
11. I. LeMay and M.R. Krishnadev: Copper in Iron and Steel, I. LeMay and L.M. Schetky, eds., John Wiley & Sons, New York, NY, 1982.
12. B.A. Graville: Proc. Int. Conf. on Welding of HSLA (Microalloyed) Structural Steels, ASM INTERNATIONAL, Metals Park, OH, 1978, pp. 85–101.
13. E.J. Czyryca: Key Engineering Materials, Trans Tech Publications, Aedermannsdorf, Switzerland, 1993, vols. 84–85, pp. 491–520.
14. M.T. Miglin, J.P. Hirth, A.R. Rosenfield, and W.A.T. Clark: Metall. Trans. A, 1986, vol. 17A, pp. 791–95.10.1007/BF02643854 ↗
15. R.P. Foley and M.E. Fine: Proc. Int. Cont. on Processing, Microstructure and Properties of Microalloyed and Other Modern HSLA Steels, ISS, Warrendale, PA, 1991, pp. 315–30.
16. A.K. Lis, M. Mujahid, C.I. Garcia, and A.J. DeArdo: Speich Symp. Proc., ISS, Warrendale, PA, 1992, pp. 29–38.
17. A.G. Fox, S. Mikalac, and M.G. Vassilaros: Speich Symp. Proc., ISS, Warrendale, PA, 1992, pp. 155–61.
18. M. Mujahid, A.K. Lis, C.I. Garcia, and A.J. DeArdo: J. Mater. Eng. Performance, 1988, vol. 7, pp. 247–57.10.1361/105994998770347981 ↗
19. S.K. Dhua, D. Mukerjee, and D.S. Sarma: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2259–70.10.1007/s11661-001-0201-z ↗
20. S.K. Dhua, Amitava Ray, and D.S. Sarma: Mater. Sci. Eng. A, 2001, vol. 318, pp. 197–210.10.1016/S0921-5093(01)01259-X ↗
21. J.W. Yoo, W.Y. Choo, and Y.W. Kim: Proc. Int. Conf. on Processing, Microstructures and Properties of Microalloyed and Other Modern HSLA Steels, Pittsburgh, PA, 1991, pp. 371–80.
22. J.Y. Yoo, W.Y. Choo, T.M. Park, and Y.W. Kim: Iron Steel Inst. Jpn. Int., 1995, pp. 1034–40.10.2355/isijinternational.35.1034 ↗
23. Guen Chul Hwang, Sunghak Lee, Jang Yong Yoo, and Wung Yong Choo: Mater. Sci. Eng., 1988, vol. A252, pp. 256–68.
24. T. Tanaka, N. Tabata, T. Hatomura, and C. Shiga: Proc. Conf., Microalloying ’75, Korchynsky et al., eds., Union Carbide Corp., 1977, pp. 107–19.
25. T. Tanaka: Inst. Metal. Rev., 1981, vol. 26, pp. 185–212.
26. R.K. Amin and F.B. Pickering: Thermomechanical Processing of Microalloyed Austenite, A.J. DeArdo, G.A. Ratz, and P.J. Wray, eds., AIME, Warrendale, PA, 1982, pp. 1–30.
27. T. Tanaka: Proc. Conf. on High Strength Low Alloy Steels, Wollongon, Australia, 1984, D.P. Dunne and T. Chandra, eds., South Coast Printers, Port Kembala, NSW, Australia, 1985, pp. 6–16.
28. C. Ouchi: Proc. Conf. on High Strength Low Alloy Steels, Wollongon, Australia, 1984, D.P. Dunne and T. Chandra, eds., South Coast Printers, Port Kembala, NSW, Australia, 1985, pp. 17–27.
29. R.H. Philips, J.G. Williams, and J.E. Croll: Proc. Int. Conf. on Microalloyed HSLA Steels, Microalloying 88, ASM INTERNATIONAL, Metals Park, OH, 1988, pp. 235–47.
30. I. Tamura, C. Ouchi, T. Tanaka, and H. Sekine: Thermomechanical Processing of High Strength Low Alloy Steels, Butterworth and Co. London, 1988.
31. B.N. Chapman, M.A. Cooke, and S.W. Thomson: Scripta Metall. Mater., 1992, vol. 26, pp. 1547–52.10.1016/0956-716X(92)90254-C ↗
32. A.J. DeArdo: Proc. Conf. Microalloying ’95, Michael Korchynsky, A.J. DeArdo, Paul Repas, and Geoff Tither, eds., ISS, Warrendale, PA, 1995, pp. 15–33.
33. Nobuo Shikanai and Masataka Suga: Physical Metallurgy of Direct-Quenched Steels, K.A. Taylor, S.W. Thomson, and F.B. Fletcher, eds., TMS, Warrendale, PA, 1993, pp. 93–105.
34. S. Sangal and S. Yannacopoulos: Can. Metall. Q., 1992, vol. 31, pp. 55–61.10.1179/cmq.1992.31.1.55 ↗
35. W.Y. Choo, C.S. Lee, and S.T. Hong: Physical Metallurgy of Direct-Quenched Steels, K.A. Taylor, S.W. Thomson, and F.B. Fletcher, eds., TMS, Warrendale, PA, 1993, pp. 77–91.
36. J.W. Martin: Recrystallisation of Two Phase Materials, Cambridge University Press, Cambridge, United Kingdom, 1980, pp. 151–58.
37. A. Yoshie, M. Fujioka, Y. Onoe, and K. Okamoto: Speich Symp. Proc., ISS, Warrendale, PA, 1992, pp. 119–27.
38. E.G. Hamburg and A.D. Wilson: Proc. Int. Symposium on Processing, Microstructure and Properties of HSLA Steels, TMS, Warrendale, PA, 1988, pp. 241–60.