journal article·2007-02

A Method for Direct Measurement of Multiaxial Stress-Strain Curves in Sheet Metal

T. Foecke, M.A. Iadicola, A. Lin, S.W. Banovic

Publisher page

Abstract

A method has been developed that allows measurement of stress-strain curves for sheet metal being deformed in multiaxial tension. The strain state is imposed using a modification of the Marciniak in-plane biaxial stretching test. Resulting stresses are measured using a modified X-ray diffraction (XRD) residual stress measurement system. This system is flexible enough to allow spatial mapping of in-plane stress and measurement of stresses at specific locations of interest on the sample, such as developing localizations. Results are presented correlating measurements on a thin strip of AA5182 with data from standard uniaxial tension test. Also presented are experimentally determined curves for this material in balanced biaxial tension in both the rolling and transverse directions.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Stoughton T.B. (2001) J. Eng. Mater. Technol., 123:417–2210.1115/1.1398083 ↗
2. Graf A., Hosford W. (1993) Metall. Mater. Trans. A, 24A:2503–1210.1007/BF02646529 ↗
3. Chen Z., Maekawa S., Takeda T. (1999) Metall. Mater. Trans. A, 30A:3069–7810.1007/s11661-999-0217-3 ↗
4. Kuwabara T., Yoshida K., Narihara K., Takahashi S. (2005) Int. J. Plasticity, 21:101–1710.1016/j.ijplas.2004.04.006 ↗
5. G. Gutscher, H.-C. Wu, G. Ngaile, and T. Altan: J. Mater. Processing Technol., vol. 146, pp. 1–7
6. Raghavan K.S. (1995) Metall. Mater. Trans. A, 26A:2075–2010.1007/BF02670679 ↗
7. Kuwabara T., Van Bael A., Iizuka E. (2002) Acta Mater., 50:3717–2910.1016/S1359-6454(02)00184-2 ↗
8. Banabic D. (2004) Annals CIRP 53(1):219–2210.1016/S0007-8506(07)60683-0 ↗
9. Marciniak Z., Kuczynski K. (1967) Int. J. Mech. Sci., 9:609–2010.1016/0020-7403(67)90066-5 ↗
10. T. Foecke, S.W. Banovic, and R.J. Fields: JOM, 2001, pp. 27–3010.1007/s11837-001-0116-6 ↗
11. Banovic S.W., Foecke T. (2003) Metall. Mater. Trans. A, 34(3):657–7110.1007/s11661-003-0100-6 ↗
12. Noyan I.C., Cohen J.B. (1987) Residual Stress: Measurement by Diffraction and Interpretation. Springer-Verlag, New York, NY10.1007/978-1-4613-9570-6 ↗
13. J.A. Pineault, M. Belassel, and M.E. Brauss: ASM Metals Handbook, 10th ed., vol. 8, Mechanical Testing, 2002, ASM, Materials Park, OH, pp. 484–9710.31399/asm.hb.v11.a0003528 ↗
14. Perry K., Noyan I.C., Rudnik P.J., Cohen J.B. (1984) Adv. X-ray Analysis, 27:159–70
15. “Standard Test Method for Uniaxial Tension Test,” ASTM E8, ASTM, Philadelphia, PA, 2000
16. Gnaeupel-Herold T., Foecke T.J., Prask H.J., Fields R.J. (2004) Mater. Sci. Eng. A, 399(1–2):26–32
17. Gnaeupel-Herold T., Prask H.J., Fields R.J., Foecke T., Xia Z.C., Lienert U. (2004) Mater. Sci. Eng. A, 366(1):104–1310.1016/j.msea.2003.08.059 ↗
18. “Standard Test Method for Verifying the Alignment of X-Ray Diffraction Instrumentation for Residual Stress Measurement,” ASTM E915, ASTM, Philadelphia, PA, 2002
19. Picu R.C., Vincze G., Ozturk F., Gracio J.J., Barlat F., Manniatty A.M. (2005) Mater. Sci. Eng. A, 390:334–4310.1016/j.msea.2004.08.029 ↗
20. “Standard Test Method for Determining the Effective Elastic Parameter for X-Ray Diffraction Method of Residual Stress,” ASTM E1426, ASTM, Philadelphia, PA, 2003
21. Parmar A., Mellor P.B. (1978) Int. J. Mech. Sci., 20:385–9110.1016/0020-7403(78)90041-3 ↗
22. “Standard Test Method for Plastic Strain Ratio r for Sheet Metal,” ASTM E517, ASTM, Philadelphia, PA, 2000
23. Parmar A., Mellor P.B. (1978) Int. J. Mech. Sci., 20:707–2010.1016/0020-7403(78)90057-7 ↗