Friction Stir Welding of HSLA-65 Steel: Part II. The Influence of Weld Speed and Tool Material on the Residual Stress Distribution and Tool Wear
Source abstract
Abstract
A set of single pass full penetration friction stir bead-on-plate and butt welds in HSLA-65 steel were produced using a range of traverse speeds (50 to 500 mm/min) and two tool materials (W-Re and PCBN). Part I described the influence of process and tool parameters on the microstructure in the weld region. This article focuses on the influence of these parameters on residual stress, but the presence of retained austenite evident in the diffraction pattern and X-ray tomographic investigations of tool material depositions are also discussed. The residual stress measurements were made using white beam synchrotron X-ray diffraction (SXRD). The residual stresses are affected by the traverse speed as well as the weld tool material. While the peak residual stress at the tool shoulders remained largely unchanged (approximately equal to the nominal yield stress (450 MPa)) irrespective of weld speed or tool type, for the W-Re welds, the width of the tensile section of the residual stress profile decreased with increasing traverse speed (thus decreasing line energy). The effect of increasing traverse speed on the width of the tensile zone was much less pronounced for the PCBN tool material.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. S.J. Barnes, A.R. Bhatti, A. Steuwer, R. Johnson, J. Altenkirch, and P.J. Withers: unpublished research, 2011.
2. P.L. Threadgill, A.J. Leonard, H.R. Shercliff, and P.J. Withers: Int. Mater. Rev., 2009, vol. 54, pp. 49–93.10.1179/174328009X411136 ↗
3. W.M. Thomas, P.L. Threadgill, and E.D. Nicholas: Sci. Technol. Weld. Join., 1999, vol. 4, pp. 365–72.10.1179/136217199101538012 ↗
4. S.J. Barnes, A. Steuwer, S. Mahawish, R. Johnson, and P.J. Withers: Mater. Sci. Eng. A, 2008, vol. 492, pp. 35–44.10.1016/j.msea.2008.02.049 ↗
5. T.J. Lienert, W.L. Stellwag, B.B. Grimmett, and R.W. Warke: Weld. J., 2003, vol. 82, pp. 1S–9S.10.1179/136217103225008847 ↗
6. A.P. Reynolds, W. Tang, M. Posada, and J. DeLoach: Sci. Technol. Weld. Join., 2003, vol. 8, pp. 455–60.10.1179/136217103225009125 ↗
7. L. Cui, H. Fujii, N. Tsuji, and K. Nogi: Scripta Metall. Mater., 2007, vol. 56, pp. 637–40.10.1016/j.scriptamat.2006.12.004 ↗
8. H. Fujii, L. Cui, N. Tsuji, M. Maeda, K. Nakata, and K. Nogi: Mater. Sci. Eng. A-Struct., 2006, vol. 429, pp. 50–57.10.1016/j.msea.2006.04.118 ↗
9. G. Cam: Int. Mater. Rev., 2011, vol. 56, pp. 1–48.10.1179/095066010X12777205875750 ↗
10. T.J. Lienert: Materials Solutions: Joining of Advanced and Speciality Materials VI, Pittsburgh, PA, Oct. 2003, pp. 28–34.
11. P.J. Konkol and M.F. Mruczek: Weld. J., 2007, vol. 86, pp. 187S–195S.
12. H.K.D.H. Bhadeshia and T. DebRoy: Sci. Technol. Weld. Join., 2009, vol. 14, pp. 193–96.10.1179/136217109X421300 ↗
13. R. Nandan, T. DebRoy, and H.K.D.H. Bhadeshia: Progr. Mater. Sci., 2008, vol. 53, pp. 980–102310.1016/j.pmatsci.2008.05.001 ↗
14. A. Steuwer, J.R. Santisteban, M. Turski, P.J. Withers, and T. Buslaps: J. Appl. Crystallogr., 2004, vol. 37, pp. 883–89.10.1107/S0021889804023349 ↗
15. P.J. Withers, M. Preuss, A. Steuwer, and J.W.L. Pang: J. Appl. Crystallogr., 2007, vol. 40, pp. 891–904.10.1107/S0021889807030269 ↗
16. H. Lombard, D.G. Hattingh, A. Steuwer, and M.N. James: Mater. Sci. Eng. A, 2009, vol. 501, pp. 119–24.10.1016/j.msea.2008.09.078 ↗
17. A. Steuwer, M. Peel, and P.J. Withers: Mater. Sci. Eng., 2006, vol. 441, pp. 187–96.10.1016/j.msea.2006.08.012 ↗
18. J. Bernath, B. Thompson, and N. Ames: 7th Int. Symp. on Friction Stir Welding, Session 03b, Awaji Island, Japan, 2008, pp. 74–78, TWI, Cambridge, United Kingdom.
19. H. Dai, J.A. Francis, H.J. Stone, H.K.D.H. Bhadeshia, and P.J. Withers: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 3070–78.10.1007/s11661-008-9616-0 ↗
20. D.G. Richards, P.B. Prangnell, S.W. Williams, and P.J. Withers: Mater. Sci. Eng., 2008, vol. 489, pp. 351–62.10.1016/j.msea.2007.12.042 ↗
21. W.K.C. Jones and P.J. Alberry: Ferritic Steels for Fast Reactor Steam Generators, British Nuclear Engineering Society, London, 1977, pp. 1–4.
22. B.K. Jasthi, W.J. Arbegast, and S.M. Howard: J. Mater. Eng. Perform., 2009, vol. 18, pp. 925–34.10.1007/s11665-008-9320-7 ↗
23. C.D. Sorensen and T.W. Nelson: Friction Stir Welding and Processing, ASM INTERNATIONAL, Materials Park, OH, 2007, pp. 111–20.