journal article·2013-10Open access

Work Hardening Behavior in Steel with Multiple TRIP Mechanisms

M. C. McGrath, D. C. Van Aken, N. I. Medvedeva, J. E. Medvedeva

Abstract

Transformation induced plasticity (TRIP) behavior was studied in steel with composition Fe-0.07C-2.85Si-15.3Mn-2.4Al-0.017N that exhibited two TRIP mechanisms. The initial microstructure consisted of both ε- and α-martensites with 27% retained austenite. TRIP behavior in the first 5% strain was predominately austenite transforming to ε-martensite (Stage I), but upon saturation of Stage I, the ε-martensite transformed to α-martensite (Stage II). Alloy segregation also affected the TRIP behavior with alloy rich regions producing TRIP just prior to necking. This behavior was explained by first principle calculations that revealed aluminum significantly affected the stacking fault energy in Fe-Mn-Al-C steels by decreasing the unstable stacking fault energy and promoting easy nucleation of ε-martensite. The addition of aluminum also raised the intrinsic stacking fault energy and caused the ε-martensite to be unstable and transform to α-martensite under further deformation. The two stage TRIP behavior produced a high strain hardening exponent of 1.4 and led to ultimate tensile strength of 1165 MPa and elongation to failure of 35%.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. J. Fekete and J. Hall: NIST Internal Report 6668, National Institute of Standards and Technology, Washington, DC, May 2012.
2. D.K. Matlock and J.G. Speer: Proceedings of the 3 rd Int. Conf. on Structural Steels, H.C. Lee, ed., The Korean Institute of Metals and Materials, Seoul, Korea, 2006, pp. 774–81.
3. L. Bracke, L. Kestens, and J. Penning: Scripta Mater., 2007, vol. 57, pp. 385–88.10.1016/j.scriptamat.2007.05.003 ↗
4. K. Spencer, J.D. Embury, K.T. Conlon, M. Veron, and Y. Brechet: Mater. Sci. Eng. A, 2004, vols. 387–389, pp. 873–81.10.1016/j.msea.2003.11.084 ↗
5. E.Yang, H. Zurob, and J. McDermid: Proc. MS&T, 2010, pp. 1914–25.
6. S. Takaki, T. Furuya, and Y. Tokunaga: ISIJ Int., 1990, vol. 30, pp. 632–38.10.2355/isijinternational.30.632 ↗
7. K. Sipos, L. Remy, and A. Pineau: Metall. Trans. A, 1976, vol. 7A, pp. 857–64.10.1007/BF02644083 ↗
8. X. Sun, K.S. Choi, A. Soulami, W.N. Liu, and M.A. Khaleel: Mater. Sci. Eng., 2009, vol. 526, pp. 140–49.10.1016/j.msea.2009.08.010 ↗
9. B. Jiang, X. Qi, S. Yang, W. Zhou, and T.Y. Hsu: Acta Mater., 1998, vol. 46(2), pp. 501–10.10.1016/S1359-6454(97)00266-8 ↗
10. J.P. Hirth: Metall. Trans., 1970, vol. 1, pp. 2367–74.10.1007/BF02642816 ↗
11. O. Grässel, G. Frommeyer, C. Derder, and H. Hofmann: J. Phys. IV France, 1997, vol. 7, pp. C5-383–88.10.1051/jp3:1997104 ↗
12. Y-K. Lee and C-S. Choi: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 355–60.10.1007/s11661-000-0271-3 ↗
13. S. Allain, J.-P. Chateau, O. Bouaziz, S. Migot and N. Guelton: Mater. Sci. Eng., 2004, vols. 387–389A, pp. 158–62.10.1016/j.msea.2004.01.059 ↗
14. H. Schumann: J. Kristall Tchnik, 1974, vol. 10, pp. 1141–50.10.1002/crat.19740091009 ↗
15. P. Yu Volosevich, V.N. Grindnev, and Y.N. Petrov: Phys. Met. Metallogr., 1976, vol. 42, pp. 126–30.
16. T. Suzuki, H. Kojima, K. Suzuki, T. Hashimoto, and M. Ichihara: Acta Metall., 1977, vol. 25, pp. 1151–62.10.1016/0001-6160(77)90202-4 ↗
17. J.W. Brooks, M.H. Loretto, and R.E. Smallman: Acta Metall., 1979, vol. 27, pp. 1839–47.10.1016/0001-6160(79)90074-9 ↗
18. J.W. Brooks, M.H. Loretto, and R.E. Smallman: Acta Metall., 1979, vol. 27, no. 12, pp. 1829–38.10.1016/0001-6160(79)90073-7 ↗
19. G.B. Olson and M. Cohen: Metall. Trans. A, 1975, vol. 6A, pp. 791–95.10.1007/BF02672301 ↗
20. T. Suzuki, H. Kojima, K. Suzuki, T Hashimot, and M Ichihara: Acta Metall., 1977, vol. 25, no. 10, pp. 1151–62.10.1016/0001-6160(77)90202-4 ↗
21. F. Lecroisey and A. Pineau: Metall. Trans., 1972, vol. 3, pp. 387–96.10.1007/BF02642042 ↗
22. C. Zener: Trans. TMS-AIME, 1946, vol. 167, pp. 513–34.
23. L. Kaufman and M. Cohen: Trans. TMS-AIME, 1956, vol. 206, pp. 1393–01.
24. L.E. Murr, K.P. Staudhammer, and S.S. Hecker: Metall. Trans. A, 1982, vol. 13A, pp. 627–35.10.1007/BF02644428 ↗
25. J. Talonen and H. Hanninen: Acta Mater., 2007, vol. 55, pp. 6108–18.10.1016/j.actamat.2007.07.015 ↗
26. G. Frommeyer, U. Brux, and P. Neumann: ISIJ Int., 2003, vol. 77(3), pp. 438–46.10.2355/isijinternational.43.438 ↗
27. M. Cai, H. Ding, Z. Tang, H. Lee, and Y. Lee: Steel Res. Int., 2011, vol. 82(3), pp. 242–48.10.1002/srin.201000132 ↗
28. N.I. Medvedeva, M.S. Park, D.C. Van Aken, and J.E. Medvedeva: arXiv:1208.0310v1 [cond-mat.mtrl-sci], 2012.
29. ASTM E 8-08, ASTM International, USA, 2008.
30. A.K. De, D.C. Murdock, M.C. Mataya, J.G. Speer, and D.K. Matlock: Scripta Mater., 2004, vol. 50, pp. 1445–49.10.1016/j.scriptamat.2004.03.011 ↗
31. Thermfact and FTT-Technologies, FactSage 6.2, Aachen, Germany, 2009.
32. T.S.Byun: Acta Mater., 2003, vol. 51, pp. 3063–71 .10.1016/S1359-6454(03)00117-4 ↗
33. D.A. Mirzayev, V.M. Schastlivtsev, and A.G. Tayzetdinova: Phys. Met. Metall., 1987, vol. 63, pp. 99–105.
34. M. Palumbo: CALPHAD, 2008, vol. 32, pp. 693–08.10.1016/j.calphad.2008.08.006 ↗
35. Payson and Savage: Trans. ASM, 1944, vol. 33, pp. 261–75.
36. K. Ishida: J. Alloys Compd., 1995, vol. 220, pp. 126–31.10.1016/0925-8388(94)06002-9 ↗
37. M. Gomez: ISIJ Int., 2009, vol. 49, no. 2, pp. 302–11.10.2355/isijinternational.49.302 ↗
38. Y.G. Kimand: Key Eng. Mater., 1993, vols. 84–85, pp. 461–71.10.4028/www.scientific.net/KEM.84-85.461 ↗