journal article·2014-10

Low Cycle Fatigue Behavior of 316LN Stainless Steel Alloyed with Varying Nitrogen Content. Part I: Cyclic Deformation Behavior

G. V. Prasad Reddy, R. Sandhya, S. Sankaran, M. D. Mathew

Publisher page

Abstract

In this study, the influence of cyclic strain amplitude on the evolution of cyclic stress–strain response and the associated cyclic deformation mechanisms in 316LN stainless steel with varying nitrogen content (0.07 to 0.22 wt pct) is reported in the temperature range 773 K to 873 K (500 °C to 600 °C). Two mechanisms, namely dynamic strain aging and secondary cyclic hardening, are found to strongly influence the cyclic stress response. Deformation substructures associated with both the mechanisms showed planar mode of deformation. These mechanisms are observed to be operative over certain combinations of temperature and strain amplitude. For strain amplitudes >0.6 pct, wavy or mixed mode of deformation is noticed to suppress both the mechanisms. Cyclic stress–strain curves revealed both single and dual-slope behavior depending on the test temperature. Increase in nitrogen content is found to increase the tendency toward planar mode of deformation, while increase in strain amplitude leads to transition from planar slip bands to dislocation cell/wall structure formation, irrespective of the nitrogen content in 316LN stainless steel.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. K. Oda, N. Kondo and K. Shibata: ISIJ International, 1990, vol. 30(8), pp. 625-631.10.2355/isijinternational.30.625 ↗
2. I. Karaman, H. Sehitoglu, H. J. Maier and Y. I. Chumlyakov: Acta mater., 2001, vol. 49, pp. 3919–3933.10.1016/S1359-6454(01)00296-8 ↗
3. A.F.Armas, O.R.Bettin, I.Alvarez-Armas and G.H.Rubiolo : J Nucl. Mater., 1988, vol. 155-157, pp. 646-649.
4. G.V. Prasad Reddy, R. Sandhya, K.B.S. Rao, and S. Sankaran: Proc. Eng., 2010, vol. 2, pp. 2181–88.10.1016/j.proeng.2010.03.234 ↗
5. M. Gerland, R. Alain, B. Ait Saadi and J. Mendez: Mater. Sci. Engg. A, 1997, vol. 229, pp. 68-86.10.1016/S0921-5093(96)10560-8 ↗
6. J.O. Nilsson: Fatigue Engng. Mater. Struct., 1984, vol. 7(1), pp. 55-64.10.1111/j.1460-2695.1984.tb00359.x ↗
7. S. Degallaix, J. Foct and A. Hendry: Mater. Sci. and Tech., 1986, vol. 2, pp. 946-950.10.1179/mst.1986.2.9.946 ↗
8. R. Taillard and J. Foct: Proc. Int. Conf. on High Nitrogen Steels, HNS’88, Lille, France, 1989, pp. 163–68.
9. S. Degallaix, G. Degallaix and J. Foct: in H.D. Solomon, G.R. Halford, L.R. Kaisand, and B.N. Leis (Eds.), Low Cycle Fatigue, ASTM STP 942, ASTM Philadelphia, 1988, pp. 798-811.
10. D.W. Kim, W.-S. Ryu, J.H. Hong, and S.-K. Choi: J. Nucl. Mater., 1998, vol. 254, pp. 226–33.10.1016/S0022-3115(97)00360-7 ↗
11. G.V. Prasad Reddy, R. Sandhya, M.D. Mathew, and S. Sankaran: Metall. Mater. Trans A, 2014, in press.
12. V.G. Gavriljuk and H. Berns: High Nitrogen Steels: Structure, Properties, Manufacture, Applications, 1st ed., Springer Verlag, Berlin, 1999.10.1007/978-3-662-03760-7 ↗
13. X. W. Zhou and M. Grujicic: Calphad, 1996, vol. 20(3), pp. 257-272.10.1016/S0364-5916(96)00029-6 ↗
14. Yu. Jagodzinski, S. Smouk, A. Tarasenko and H. Hänninen: Mater. Sci. Forum, 1999, vol. 318-320, pp. 309-314.10.4028/www.scientific.net/MSF.318-320.309 ↗
15. M.D. Mathew, K. Laha and V. Ganesan: Mater. Sci. Engg. A, 2012, vol. 535, pp. 76– 83.10.1016/j.msea.2011.12.044 ↗
16. G. Wahlberg, U. Rolander, and H.O. Andren: Proc. Int. Conf. on High Nitrogen Steels, HNS’88, Lille, France, 1989, pp. 163–68.
17. M. Murayama, K. Hono, H. Hirukawa, T. Ohmura and S. Matsuoka: Scripta Mater., 1999, vol. 41(5), pp. 467-473.10.1016/S1359-6462(99)00194-3 ↗
18. V.V. Sumin, G. Chimid, T. Rashev and L. Saryivanov: Mater. Sci. Forum, 1999, vol. 318-320, pp. 31-40.10.4028/www.scientific.net/MSF.318-320.31 ↗
19. A.P.L. Turner: Metall. Trans. A, 1979, vol. 10A, pp. 225-234.10.1007/BF02817632 ↗
20. L. Remy and A.Pineau: Mater. Sci. and Engg., 1978, vol. 36, pp. 47 – 63.10.1016/0025-5416(78)90194-5 ↗
21. A.H.Cottrell: Dislocations and plastic flow in crystals, Oxford University, London, 1953.
22. A.W.Sleeswyk: Acta Metall., 1958, vol. 6(9), pp. 598-603.10.1016/0001-6160(58)90101-9 ↗
23. G.V. PrasadReddy, R. Sandhya, M. Valsan, and K.B.S. Rao: Mater. Sci. Technol., 2010, vol. 26(11), pp. 1384–92.10.1179/174328408X317110 ↗
24. C.F. Jenkins and G.V. Smith: Trans. Metall. Soc. AIME, 1969, vol. 245, pp. 2149–56.
25. K.G. Samuel, S.L. Mannan and P. Rodriguez: Acta. Metall., 1988, vol. 36 (8), pp. 2323-2327.10.1016/0001-6160(88)90331-8 ↗
26. Seong-Gu Hong and Soon-Bok Lee: J of Nucl. Mater., 2005, vol. 340(2-3), pp. 307-314.10.1016/j.jnucmat.2004.12.012 ↗
27. D. Pecker and I.M. Bernstein, Handbook of Stainless Steels, McGraw-Hill, New York, 1977.
28. Byung Sup Rho and Soo Woo Nam: J of Nucl Mater., 2002, vol. 300, pp. 65–72.10.1016/S0022-3115(01)00709-7 ↗
29. V.S. Srinivasan, M. Valsan, R. Sandhya, K. B. S. Rao, S.L.Mannan and D.H.Sastry: Int. J. Fat., 1999, vol. 21, pp. 11–21.10.1016/S0142-1123(98)00052-8 ↗
30. J. Man, K. Obrtlík, M. Petrenec, P. Beran, M. Smaga, A. Weidner, J. Dluhoš, T. Kruml, H. Biermann, D. Eifler and J. Polák: Procedia Engineering, 2011, vol. 10, pp. 1279-1284.10.1016/j.proeng.2011.04.213 ↗
31. Chia-Chang Shiha, New-Jin Hoa and Hsing-Lu Huangb: Mater. Characterization, 2009, vol. 60, pp. 1280-1288.10.1016/j.matchar.2009.05.013 ↗
32. G.V. Prasad Reddy, R. Sandhya, M.D. Mathew, and S. Sankaran: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 5625–29.10.1007/s11661-013-2042-y ↗
33. H.S. Chen, J.J. Gilman and A.K. Head: J. of Applied Physics, 1964, vol. 35(8), pp. 2502-2514.10.1063/1.1702890 ↗