journal article·2009-01

Effect of Temperature on the Wear Behavior of Al-7Si-TiB2 In-Situ Composites

S. Kumar, V. Subramanya Sarma, B.S. Murty

Publisher page

Abstract

In this article, the effect of temperature and load on the dry sliding wear behavior of an Al-7Si alloy reinforced with in-situ TiB2 particles is reported. The coefficient of friction and wear rate of Al-7Si alloy and in-situ composites were measured using a high-temperature pin-on-disc apparatus. The wear tests were performed in the temperature range of 100 °C to 300 °C, at an applied load of 40 to 120 N. With increasing temperature, the wear rate of Al-7Si alloy increased drastically and it decreased with the increase in weight percent of TiB2 particles. The transition from mild to severe wear for Al-7Si alloy was observed at 80, 60, and 40 N at temperatures of 100 °C, 150 °C, and 200 °C, respectively. The alloy reinforced with 5 wt pct of TiB2 showed the transition at 120 N and 200 °C, and the transition load further decreased to 80 N at 300 °C. However, within the present experimental range of load, the addition of 10 wt pct of TiB2 showed the transition only at 100 N and 300 °C. The addition of TiB2 particles increases the wear resistance properties of Al-7Si alloy even at high temperature.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · MXene and MAX Phase Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. A.P. Sannino, H.J. Rack: Wear, 1995, vol. 18, pp. 1–1910.1016/0043-1648(95)06657-8 ↗
2. R.L. Deuis, C. Subramanian, J.M. Yellup: Comp. Sci. Technol., 1997, vol. 57, pp. 415–3510.1016/S0266-3538(96)00167-4 ↗
3. M.A. Martinez, A. Martin, J. Llorca: Scripta Mater, 1993, vol. 28, pp. 207–1210.1016/0956-716X(93)90564-9 ↗
4. A. Martin, M.A. Martinez, J. Llorca: Wear, 1996, vol. 193, pp. 169–7910.1016/0043-1648(95)06704-3 ↗
5. A. Martin, J. Rodriguez, J. Llorca: Wear, 1999, vols. 225–229, pp. 615–2010.1016/S0043-1648(98)00385-8 ↗
6. J. Rodriguez, A. Martin, J. Llorca: Acta Mater., 2000, vol. 48, pp. 993–100310.1016/S1359-6454(99)00356-0 ↗
7. J. Singh, A.T. Alpas: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3135–4810.1007/BF02663864 ↗
8. S. Wilson, A.T. Alpas: Wear, 1997, vol. 212, pp. 41–4910.1016/S0043-1648(97)00142-7 ↗
9. S.Q. Wu, H.Z. Wang, S.C. Tjong: Comp. Sci. Technol., 1996, vol. 56, pp. 1261–7010.1016/S0266-3538(96)00085-1 ↗
10. Y.H. Liu, J. Du, S.R. Yu, W. Wang: Wear, 2004, vol. 256, pp. 275–8510.1016/S0043-1648(03)00531-3 ↗
11. G. Straffelini, M. Pellizzari, A. Molinari: Wear, 2004, vol. 256, pp. 754–6310.1016/S0043-1648(03)00529-5 ↗
12. M.H. Korkut: Mater. Sci. Technol., 2004, vol. 20, pp. 73–8110.1179/174328413X13789824293542 ↗
13. S.C. Tjong, Z.Y. Ma: Mater. Sci. Eng. R, 2000, vol. 29, pp. 49–11310.1016/S0927-796X(00)00024-3 ↗
14. S.C. Tjong, K.F. Tam, S.Q. Wu: Comp. Sci. Technol., 2003, vol. 63, pp. 89–9710.1016/S0266-3538(02)00200-2 ↗
15. M. Huang, X. Li, H. Yi, N. Ma, H. Wang: J. Alloys Compd., 2005, vol. 389, pp. 275–8010.1016/j.jallcom.2004.07.052 ↗
16. H. Yi, N. Ma, X. Li, Y. Zhang, H. Wang: Mater. Sci. Eng. A, 2006, vol. 419, pp 12–1710.1016/j.msea.2005.10.020 ↗
17. S. Kumar, V. Subramanya Sarma, B.S. Murty: Mater. Sci. Eng. A, 2008, vol. 476, pp. 333–4010.1016/j.msea.2007.04.113 ↗
18. S. Kumar, M. Chakraborty, V. Subramanya Sarma, B.S. Murty: Wear, 2008, vol. 265, pp. 134–4210.1016/j.wear.2007.09.007 ↗
19. A.K. Prasada Rao, B.S. Murty, M. Chakraborty: Mater. Sci. Eng. A, 2005, vol. 395, pp. 323–2610.1016/j.msea.2004.12.053 ↗
20. A.K. Prasada Rao, K. Das, B.S. Murty, M. Chakraborty: Wear, 2006, vol. 261, pp. 133–3910.1016/j.wear.2005.09.012 ↗