journal article·2008-10

Deformation Geometry and Through-Thickness Strain Gradients in Asymmetric Rolling

R. Roumina, C.W. Sinclair

Publisher page

Abstract

Experiments and simulations focusing on cold rolling under conditions where the work roll velocities are different (asymmetric rolling) have been performed to provide a basic framework for understanding the effects of the roll velocity ratio and deformation geometry on through thickness shear strain development. It is shown that deformation geometry, controlled by varying the reduction per pass, has a significant impact on the through thickness shear strain gradients at a given level of asymmetry. Large reductions per pass lead to more uniform through thickness shear strains, but lower overall shear strain magnitudes compared to rolling conditions involving small reductions per pass. Moreover, the results show that a critical value of the roll velocity ratio exists, for a fixed set of rolling conditions, above which the shear strains induced by asymmetric rolling remain unchanged. This is interpreted based on the relative importance of geometrically induced shear strains and those arising from frictional effects. In this context, the position of the neutral points plays a vital role.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. K.-H. Kim, D.N. Lee: Acta Mater., 2001, vol. 49, pp. 2583–9510.1016/S1359-6454(01)00036-2 ↗
2. S.H. Lee, D.N. Lee: Int. J. Mech. Sci., 2001, vol. 43, pp. 1997–201510.1016/S0020-7403(01)00025-X ↗
3. S.-B. Kang, B.-K. Min, H.-W. Kim, D.S. Wilkinson, J. Kang: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 3141–4910.1007/s11661-005-0085-4 ↗
4. J.-S. Lee, H.-T. Son, Y.-K. Kim, K.-Y. Lee, H.-M. Kim, I.-H. Oh: Key Eng. Mater., 2007, vols. 345–346, pp. 77–80
5. H. Jin, D.J. Lloyd: Mater. Sci. Eng., 2007, vol. A465, pp. 267–7310.1016/j.msea.2007.02.128 ↗
6. A.B. Richelsen: Int. J. Mech. Sci., 1997, vol. 39, pp. 1199–21110.1016/S0020-7403(97)00013-1 ↗
7. H. Watanabe, T. Mukai, K. Ishikawa: J. Mater. Sci., 2004, vol. 39, pp. 1477–8010.1023/B:JMSC.0000013922.16079.d3 ↗
8. Y.-M. Hwang, G.-Y. Tzou: Int. J. Mech. Sci., 1997, vol. 39, pp. 289–30310.1016/S0020-7403(96)00024-0 ↗
9. T. Sakai, K. Yoneda, Y. Saito: Mater. Sci. Forum, 2002, vols. 396–402, pp. 309–1410.4028/www.scientific.net/MSF.396-402.309 ↗
10. T. Sakai, S. Hamada, Y. Saito: Scripta Mater., 2001, vol. 44, pp. 2569–7310.1016/S1359-6462(01)00932-0 ↗
11. H. Jin, D.J. Lloyd: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 997–100610.1007/s11661-004-0026-7 ↗
12. H. Jin, D.J. Lloyd: Mater. Sci. Forum, 2004, vols. 467–470, pp. 381–8610.4028/www.scientific.net/MSF.467-470.381 ↗
13. S.-H. Kim, J.K. Lee, and D.N. Lee: Proc. Ultra Fine Grained Materials II, Seattle, WA, 2002, TMS, Warrendale, PA, pp. 55–6310.1002/9781118804537.ch7 ↗
14. D.N. Lee: Mater. Sci. Forum, 2004, vols. 449–452, pp. 1–610.4028/www.scientific.net/MSF.449-452.1 ↗
15. J. Lee, D.N. Lee: Key Eng. Mater., 2007, vols. 340–341, pp. 619–26
16. Y. Nakaura, A. Watanabe, K. Ohori: J. Jpn. Inst. Light Met., 2007, vol. 57, pp. 67–7310.2464/jilm.57.67 ↗
17. W.A. Backofen: Deformation Processing, Addison-Wesley, Reading, MA, 1972
18. R. Sowerby: Finite Strain Determination in Sheet Metal Stampings (William Johnson Commem Vol), Pergamon Press, Oxford, United Kingdom, 1985, pp. 123–34
19. H. Ahmed, M.A. Wells, D.M. Maijer, B.J. Howes, M.R. van der Winden: Mater. Sci. Eng. A, 2005, vol. 390, pp. 278–9010.1016/j.msea.2004.08.045 ↗
20. J. Go, W.J. Poole, M. Militzer, M.A. Wells: Mater. Sci. Technol., 2003, vol. 19, pp. 1361–6810.1179/026708303225005980 ↗