Low-Cycle Fatigue Behavior of Die-Cast Mg Alloys AZ91 and AM60
Source abstract
Abstract
The influence of microstructure and artificial aging response (T6) on the low-cycle fatigue behavior of super vacuum die-cast (SVDC) AZ91 and AM60 has been investigated. Fatigue lifetimes were determined from the total strain-controlled fatigue tests for strain amplitudes of 0.2 pct, 0.4 pct, 0.6 pct, 0.8 pct, and 1.0 pct under fully reversed loading at a frequency of 5 Hz. Cyclic stress–strain behavior was determined using an incremental step test (IST) and compared with the more traditional constant amplitude test. Two locations in a prototype casting were investigated to examine the role of microstructure and porosity on fatigue behavior. At all total strain amplitudes microstructure refinement had a negligible impact on fatigue life because of significant levels of porosity. AM60 showed an improvement in fatigue life at higher strain amplitudes when compared with AZ91 because of higher ductility. T6 heat treatment had no impact on fatigue life. Cyclic stress–strain behavior obtained via the incremental step test varied from constant amplitude test results due to load history effects. The constant amplitude test is believed to be the more accurate test method. In general, larger initiation pores led to shorter fatigue life. The fatigue life of AZ91 was more sensitive to initiation pore size and pore location than AM60 at the lowest tested strain amplitude of 0.2 pct. Fatigue crack paths did not favor any specific phase, interdentritic structure or eutectic structure. A multistage fatigue (MSF) model showed good correlation to the experimental strain-life results. The MSF model reinforced the dominant role of inclusion (pore) size on the scatter in fatigue life.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. E. Aghion and B. Bronfin: Mater. Sci. Forum, 2000, vols. 350–351, pp. 19–30.10.4028/www.scientific.net/MSF.350-351.19 ↗
2. United States Automotive Materials Partnership (USAMP) Automotive Metals Division (AMD): Magnesium Vision 2020: A North American Automotive Strategic Vision for Magnesium, unpublished research, (2006)
3. J.F. King: Magnesium Alloys Their Applications., [Pap. Conf.], 1998, pp. 37–47.
4. C. Potzies and K. Kainer: Adv. Eng. Mater., 2004, vol. 6, no. 5, pp. 281–89.10.1002/adem.200400021 ↗
5. M. Yoo, S. Agnew, J. Morris, and K. Ho: Mater. Sci. Eng. A, 2001, vols. 319–321, pp. 87–92.10.1016/S0921-5093(01)01027-9 ↗
6. M.F. Horstemeyer, N. Yang, K. Gall, D. McDowell, J. Fan, and P. Gullett: Fatigue Fract. Eng. Mater. Struct., 2002, vol. 25, no. 11, pp. 1045–56.10.1046/j.1460-2695.2002.00594.x ↗
7. H.R. Mayer, H. Lipowsky, M. Papakyriacou, R. Rösch, A. Stich, and S.E. Stanzl-Tschegg: Fatigue Fract. Eng. Mater. Struct., 1999, vol. 22, no. 7, pp. 591–99.10.1046/j.1460-2695.1999.00205.x ↗
8. Y. Murakami: Metal Fatigue: Effects of Small Defects and Nonmetallic Inclusions, 1st ed., Elsevier Science Ltd., Oxford, U.K., 2002, pp. 11–15.10.1016/B978-008044064-4/50002-5 ↗
9. K. Gall, M.F. Horstemeyer, B.W. Degner, D.L. McDowell, and J.H. Fan: Int. J. Fatigue, 2001, vol. 108, pp. 207–33.
10. Q.G. Wang, D. Apelian, and D.A. Lados: J. Light Met., 2001, vol. 1, no. 1, pp. 73–84.10.1016/S1471-5317(00)00008-0 ↗
11. M. Horstemeyer: Acta Mater., 2004, vol. 52, no. 5, pp. 1327–36.10.1016/j.actamat.2003.11.018 ↗
12. L.J. Chen, J. Shen, W. Wu, F. Li, Y. Wang, and Z. Liu: Mater. Sci. Forum, 2005, vols. 488–489, pp. 725–28.10.4028/www.scientific.net/MSF.488-489.725 ↗
13. G. Eisenmeier, B. Holzwarth, H. Hoppel, and H. Mughrabi: Mater. Sci. Eng. A, 2001, vols. 319–321, pp. 578–82.10.1016/S0921-5093(01)01105-4 ↗
14. F. Li, Y. Wang, L. Chen, Z. Liu, and J. Zhou: J. Mater. Sci., 2005, vol. 40, no. 6, pp. 1529–31.10.1007/s10853-005-0597-8 ↗
15. H. El Kadiri, M. Horstemeyer, J. Jordon, and Y. Xue: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 190–205.10.1007/s11661-007-9328-x ↗
16. K. Gall: Int. J. Fatigue, 2004, vol. 26, no. 1, pp. 59–70.10.1016/S0142-1123(03)00079-3 ↗
17. Y. Lu, F. Taheri, M. Gharghouri, and H. Han: J. Alloys Compd., 2009, vol. 470, nos. 1–2, pp. 202–13.10.1016/j.jallcom.2008.03.008 ↗
18. D.L. Goodenberger and R.I. Stephens: J. Eng. Mater. Technol., 1993, vol. 115, no. 4, p. 391.10.1115/1.2904236 ↗
19. S.-J. Li, S.-M. Xiong, B.-C. Liu, M. Li, and J. Allison: Proc. Magnesium Technol Symp. 2010, pp. 613–16.
20. ASTM B661-06, 2006.
21. ASTM E606-04, 2005.
22. R.W. Landgraf, J. Morrow, and T. Endo: J. Mater., 1969, vol. 4, no. 1, pp. 176–88.
23. ASTM E112-96, 2006.
24. S. Celotto: Acta Mater., 2000, vol. 48, pp. 1775–87.10.1016/S1359-6454(00)00004-5 ↗
25. T. Abbott, M.A. Easton, and W. Song: Mater. Sci. Forum, 2003, vols. 419–422, pp. 141–46.10.4028/www.scientific.net/MSF.419-422.141 ↗
26. M.R. Mitchell, ASM Handbook, vol. 19, ASM International, Materials Park, OH, 1996, pp. 227–49.
27. J. Polak, M. Klensnil, and P. Lukas: Mater. Sci. Eng., 1977, vol. 28, pp. 109–17.10.1016/0025-5416(77)90094-5 ↗
28. J. Polak and M. Hajek: Int. J. Fatigue, 1991, vol. 13, no. 3, pp. 216–22.10.1016/0142-1123(91)90244-S ↗
29. S. Suresh: Fatigue of Materials, 2nd ed., Cambridge University Press, New York, NY, 1998, p. 92.10.1017/CBO9780511806575 ↗
30. S. Barbagallo: Int. J. Cast Met. Res., 2004, vol. 17, no. 6, pp. 364–69.10.1179/136404604225022676 ↗
31. H. Patel, D. Chen, S. Bhole, and K. Sadayappan: J. Alloys Compd., 2010, vol. 496, nos. 1–2, pp. 140–48.10.1016/j.jallcom.2010.02.042 ↗
32. D.L. McDowell, K. Gall, M.F. Horstemeyer, and J. Fan: Eng. Fract. Mech., 2003, vol. 70, p. 49.10.1016/S0013-7944(02)00021-8 ↗
33. Y. Xue, M. Horstemeyer, D. McDowell, H. El Kadiri, and J. Fan: Int. J. Fatigue, 2007, vol. 29, no. 4, pp. 666–76.10.1016/j.ijfatigue.2006.07.005 ↗
34. Y. Xue, H. El Kadiri, M.F. Horstemeyer, J. Jordon, and H. Weiland: Acta Mater., 2007, vol. 55, p. 1975.10.1016/j.actamat.2006.11.009 ↗
35. Y. Xue, A.M. Wright, D.L. McDowell, M.F. Horstemeyer, K.N. Solanki, and Y. Hammi: J. Eng. Mater. Technol., 2010, vol. 132, p. 1.10.1115/1.4000227 ↗
36. Y. Xue, A. Pascu, M.F. Horstemeyer, L. Wang, and P.T. Wang: Acta Mater., 2010, vol. 58, p. 4029.10.1016/j.actamat.2010.03.014 ↗
37. J. Jordon, M.F. Horstemeyer, N. Yang, J.F. Major, K.A. Gall, and J. Fan: Metall. Mater. Trans. A, 2010, vol. 528, p. 6860.
38. J. Jordon, J.B. Gibson, M.F. Horstemeyer, H. El Kadiri, J.C. Baird, and A.A. Luo: Mater. Sci. Eng. A, in Press.
39. K. Gall, M.F. Horstemeyer, D.L. McDowell, and J. Fan: Mech. Mater., 2000, vol. 32, p. 277.10.1016/S0167-6636(00)00003-X ↗
40. D.R. Hayhurst, F.A. Leckie, and D.L. McDowell: ASTM Spec. Tech. Publ., 1985, p. 688.10.1520/STP36250S ↗
41. S. Groh, E.B. Marin, M.F. Horstemeyer, and D.J. Bammann: Modell. Simul. Mater. Sci. Eng., 2009, vol. 17, pp. 1–15.10.1088/0965-0393/17/7/075009 ↗
42. K. Shiozawa, Y. Tohda, and S.-M. Sun: Fatigue Fract. Eng. Mater. Struct., 1997, vol. 20, pp. 237–47.10.1111/j.1460-2695.1997.tb00281.x ↗
43. J.D. Bernard, J. Jordon, and M.F. Horstemeyer: Symp. Sponsored by the Magnesium Committee of the Light Metals Division of the Minerals, Metals and Materials Society (TMS), Magnesium Technology, 2011, p. 67.10.1002/9781118062029.ch15 ↗
44. J. Jordon, J.D. Bernard, and J.C. Newman Jr.: Int. J. Fatigue, 2012, vol. 36, no. 1, pp. 206–10.10.1016/j.ijfatigue.2011.07.016 ↗