Development of New High-Strength Carbide-Free Bainitic Steels
Source abstract
Abstract
An attempt was made to optimize the mechanical properties by tailoring the process parameters for two newly developed high-strength carbide-free bainitic steels with the nominal compositions of 0.47 pct C, 1.22 pct Si, 1.07 pct Mn, 0.7 pct Cr (S1), and 0.30 pct C, 1.76 pct Si, 1.57 pct Mn, and 0.144 pct Cr (S2) (wt pct), respectively. Heat treatment was carried out via two different routes: (1) isothermal transformation and (2) quenching followed by isothermal tempering. The results for the two different processes were compared. The bainitic steels developed by isothermal heat treatment were found to show better mechanical properties than those of the quenched and subsequently tempered ones. The effect of the fraction of the phases, influence of the transformation temperatures, the holding time, and the stability of retained austenite on the mechanical properties of these two steels was critically analyzed with the help of X-ray diffraction, optical metallography, scanning electron microscopy, and atomic force microscopy. Finally, a remarkable combination of yield strength of the level of 1557 MPa with a total elongation of 15.5 pct was obtained.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. C. Gracia-Mateo and F.G. Caballero: ISIJ Int., 2005, vol. 45, pp. 1736–40.10.2355/isijinternational.45.1736 ↗
2. H.K.D.H. Bhadeshia: Proc. 3rd Int. Conf. on Advanced Structural Steels, Gyeongju, Korea, Aug. 22–24, 2006, pp. 33–40.
3. R. Bakhtiari and A. Ekrami: Mater. Sci. Eng. A, 2009, vol. 525, pp. 159–65.10.1016/j.msea.2009.07.042 ↗
4. H.K.D.H. Bhadeshia and J.W. Christian: Metall. Trans. A, 1990, vol. 21A, pp. 767–97.10.1007/BF02656561 ↗
5. F.G. Caballero and H.K.D.H. Bhadeshia: Curr. Opin. Solid State Mater. Sci., 2004, vol. 8, pp. 251–57.10.1016/j.cossms.2004.09.005 ↗
6. L.C. Chang: Wear, 2005, vol. 258, pp. 730–43.10.1016/j.wear.2004.09.064 ↗
7. H.K.D.H. Bhadeshia and D.V. Edmonds: Met. Sci., 1983, vol. 17, pp. 411–19.10.1179/030634583790420600 ↗
8. H.K.D.H. Bhadeshia and D.V. Edmonds: Met. Sci., 1983, vol. 17, pp. 420–25.10.1179/030634583790420646 ↗
9. Natalia Luzginova, Lie Zhao, and Jilt Sietsma: Mater. Sci. Eng. A, 2007, vol. 448, pp. 104–10.10.1016/j.msea.2006.10.014 ↗
10. H.K.D.H. Bhadeshia: Mater. Sci. Forum, 2005, vols. 500–501, pp. 63–74.10.4028/www.scientific.net/MSF.500-501.63 ↗
11. H.K.D.H. Bhadeshia and D.V. Edmonds: Acta Metall., 1980, vol. 28, pp. 1265–73.10.1016/0001-6160(80)90082-6 ↗
12. H.K.D.H. Bhadeshia: Acta Metall., 1981, vol. 29, pp. 1117–30.10.1016/0001-6160(81)90063-8 ↗
13. J. Chakraborty, D. Bhattacharjee, and I. Manna: Scripta Mater., 2009, vol. 61, pp. 604–07.10.1016/j.scriptamat.2009.05.035 ↗
14. P.M. Brown and D.P. Baxter: Mater. Sci. Technol., 2004, vol. 1, pp. 433–38.
15. F.G. Caballero, H.K.D.H. Bhadeshia, K.J.A. Mawella, D.G. Jones, and P. Brown: Mater. Sci. Technol., 2001, vol. 17, pp. 512–16.10.1179/026708301101510348 ↗
16. F.G. Caballero, H.K.D.H. Bhadeshia, K.J.A. Mawella, D.G. Jones, and P. Brown. Mater. Sci. Technol., 2001, vol. 17, pp. 517–22.10.1179/026708301101510357 ↗
17. L.C. Chang and H.K.D.H. Bhadeshia: Mater. Sci. Eng. A, 1994, vol. 184, pp. L17–L19.10.1016/0921-5093(94)91079-0 ↗
18. K. Andrews: J. Iron Steel Inst., 1970, vol. 24, pp. 3618–26.
19. Z. Zhao, C. Cheng, Y. Liu, and D.O. Northwood: J. Mater. Sci., 2001, vol. 36, pp. 5045–56.10.1023/A:1011874708194 ↗
20. B.D. Cullity: Elements of X-Ray Diffraction, Addison-Wesley, Boston, MA, 1959, pp. 388–96.
21. H.K.D.H. Bhadeshia and D.V. Edmonds: Metall. Trans. A, 1979, vol. 10A, pp. 895–907.10.1007/BF02658309 ↗
22. J. Chakraborty, D. Bhattacharjee, and I. Manna: Scripta Mater., 2008, vol. 59, pp. 247–50.10.1016/j.scriptamat.2008.03.023 ↗
23. A. Barbacki: J. Mater. Process. Technol., 1995, vol. 53, pp. 57–63.10.1016/0924-0136(95)01961-D ↗
24. S. Zaefferer, J. Ohlert, and W. Bleck: Acta Mater., 2004, vol. 52 (9), pp. 2765–78.10.1016/j.actamat.2004.02.044 ↗
25. A. Hanzaki and P. Hodgson: ISIJ Int., 1995, vol. 35, pp. 79–85.10.2355/isijinternational.35.79 ↗
26. W.C. Jeong, D.K Matlock, and G Krauss: Mater. Sci. Eng. A, 1993, vol. 165, pp. 9–18.10.1016/0921-5093(93)90621-K ↗
27. G.E. Dieter: Mechanical Metallurgy, 2nd ed., McGraw-Hill Book Co., New York, NY, 1976, pp. 282–83.