The Mechanism of Grain Coarsening in Friction-Stir-Welded AA5083 after Heat Treatment
Source abstract
Abstract
Friction stir welding (FSW) takes place in the solid state, thus providing potential advantages of welds of high strength and ductility because of fine microstructures. However, post-FSW heat treatment can create very coarse grains, potentially reducing mechanical properties. AA5083-H18 sheets were friction-stir butt welded using three sets of welding parameters representing a wide range of heat input. They were then heat treated for 5 minutes at 738 K (465 °C), producing grain sizes exceeding 100 μm near the top weld surfaces, with the coarse grains extending toward the bottom surface to various degrees depending on the welding parameters. Electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), optical metallography, inductively coupled plasma–mass spectrometry, and Vickers hardness testing were used to characterize the regions within welds. Particle pinning was determined quantitatively and used with Humphreys’ model of grain growth to interpret the behavior. The mechanism responsible for forming the large grains was identified as abnormal grain growth (AGG), with AGG occurring only for regions with pre-heat-treatment grain sizes smaller than 3 μm. Second-phase particle volume fractions and sizes, textures, and solute concentrations were not significantly different in AGG and non-AGG regions. Ultrafine grain layers with grain diameters of 0.3 mm were characterized and had high densities of pinning particles of MgSi2, Al2O3, and Mg5Al8. Strategies to eliminate AGG by alloy and weld process design were discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. C.J. Dawes: Weld. Met. Fabric., 1995, vol. 63, pp. 13–16.
2. Y.S. Sato and H. Kokawa: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 3023–31.10.1007/s11661-001-0177-8 ↗
3. W.J. Arbegast and P.J. Hartley: Proc. 5th Int. Conf. on Trends in Welding Research, Pine Mountain, GA, 1998, pp. 541–46.
4. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng., R, 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
5. I. Charit, R.S. Mishra, and M.W. Mahoney: Scripta Mater., 2002, vol. 47, pp. 631–36.10.1016/S1359-6462(02)00257-9 ↗
6. F.I. Saunders and R.H. Wagoner: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2605–16.10.1007/BF02652354 ↗
7. M.C. Stasik and R.H. Wagoner: Int. J. Form. Processes, 1998, vol. 1, pp. 9–33.
8. Z.C. Yao, L. Zhang, S. Kariat, and Y.J. Zhou: SAE World Congress & Exhibition, SAE 2007-01-0421, Detroit, MI, 2007.
9. Y.S. Sato, T.W. Nelson, C.J. Sterling, R.J. Steel, and C.O. Pettersson: Mater. Sci. Eng., A, 2005, vol. 397, pp. 376–84.10.1016/j.msea.2005.02.054 ↗
10. S.H.C. Park, Y.S. Sato, H. Kokawa, K. Okamoto, S. Hirano, and M. Inagaki: Sci. Technol. Weld. Join., 2005, vol. 10, pp. 550–56.10.1179/174329305X46691 ↗
11. Y.S. Sato, T.W. Nelson, and C.J. Sterling: Acta Mater., 2005, vol. 53, pp. 637–45.10.1016/j.actamat.2004.10.017 ↗
12. S.H.C. Park, Y.S. Sato, and H. Kokawa: J. Mater. Sci., 2003, vol. 38, pp. 4379–83.10.1023/A:1026351619636 ↗
13. T. Kawasaki, T. Makina, S. Todori, H. Takai, M. Ezumi, and Y. Ina: Proc. 2nd Int. Symp. on FSW, Gotherburg, Sweden, 2000.
14. M.R. Johnsen: Weld. J., 1999, vol. 78, pp. 35–39.
15. E.D. Nicholas and W.M. Thomas: Int. J. Mater. Prod. Tech., 1998, vol. 13, pp. 45–55.
16. S.W. Kallee and A. Mistry: Proc. 1st Int. Symp. on FSW, Thousand Oaks, CA, 1999.
17. O.T. Midling, J.S. Kvale, and O. Dahl: Proc. 1st Int. Symp. on FSW, Thousand Oaks, CA, 1999, pp. 14–16.
18. S. Benavides, Y. Li, L.E. Murr, D. Brown, and J.C. McClure: Sci. Mater., 1999, vol. 41, pp. 809–15.
19. O.V. Flores, C. Kennedy, L.E. Murr, D. Brown, S. Pappu, B.M. Nowak, and J.C. McClure: Scripta Mater., 1998, vol. 38, pp. 703–08.10.1016/S1359-6462(97)00551-4 ↗
20. Y. Li, L.E. Murr, and J.C. McClure: Scripta Mater., 1999, vol. 40, pp. 1041–46.10.1016/S1359-6462(99)00062-7 ↗
21. G. Liu, L.E. Murr, C.S. Niou, J.C. McClure, and F.R. Vega: Scripta Mater., 1997, vol. 37, pp. 355–61.10.1016/S1359-6462(97)00093-6 ↗
22. L.E. Murr, G. Liu, and J.C. McClure: J. Mater. Sci., 1998, vol. 33, pp. 1243–51.10.1023/A:1004385928163 ↗
23. Y.S. Sato, H. Kokawa, M. Enomoto, and S. Jogan: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2429–37.10.1007/s11661-999-0251-1 ↗
24. Y.S. Sato, H. Kokawa, M. Enomoto, S. Jogan, and T. Hashimoto: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3125–30.10.1007/s11661-999-0223-5 ↗
25. C.G. Rhodes, M.W. Mahoney, W.H. Bingel, R.A. Spurling, and C.C. Bampton: Scripta Mater., 1997, vol. 36, pp. 69–75.10.1016/S1359-6462(96)00344-2 ↗
26. W.J. Arbegast: Hot Deformation of Aluminum Alloys III, TMS, Warrendale, PA, 2003, pp. 313–27.
27. W. Tang, X. Guo, J.C. McClure, and L.E. Murr: J. Mater. Process Manu., 1999, vol. 7, pp. 163–72.10.1106/55TF-PF2G-JBH2-1Q2B ↗
28. S. Benavides, Y. Li, L.E. Murr, D. Brown, and J.C. McClure: Scripta Mater., 1999, vol. 41, pp. 809–15.10.1016/S1359-6462(99)00226-2 ↗
29. V. Dixit, R.S. Mishra, R.J. Lederich, and R. Talwar: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 334–40.10.1179/174329307X197593 ↗
30. T. Hashimoto, S. Jyogan, K. Nakata, Y.G. Kim, and M. Ushio: Proc. 1st Int. Symp. on FSW, Thousand Oaks, CA, 1999.
31. Y. Li, L.E. Murr, and J.C. McClure: Mater. Sci. Eng., A, 1999, vol. 271, pp. 213–23.10.1016/S0921-5093(99)00204-X ↗
32. Z.Y. Ma, R.S. Mishra, M.W. Mahoney, and R. Grimes: Mater. Sci. Eng., A, 2003, vol. 351, pp. 148–53.10.1016/S0921-5093(02)00824-9 ↗
33. J.Q. Su, T.W. Nelson, R. Mishra, and M. Mahoney: Acta Mater., 2003, vol. 51, pp. 713–29.10.1016/S1359-6454(02)00449-4 ↗
34. I. Charit and R.S. Mishra: Mater. Sci. Eng., A, 2003, vol. 359, pp. 290–96.10.1016/S0921-5093(03)00367-8 ↗
35. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, R.A. Spurling, and W.H. Bingel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955–64.10.1007/s11661-998-0021-5 ↗
36. L.E. Murr, Y. Li, R.D. Flores, E.A. Trillo, and J.C. McClure: Mater. Res. Innov., 1998, vol. 2, pp. 150–63.10.1007/s100190050078 ↗
37. B. Heinz and B. Skrotzki: Metall. Mater. Trans. B, 2002, vol. 33B, pp. 489–98.10.1007/s11663-002-0059-5 ↗
38. J.Q. Su, T.W. Nelson, and C.J. Sterling: J. Mater. Res., 2003, vol. 18, pp. 1757–60.10.1557/JMR.2003.0243 ↗
39. J.G. Schroth: Advances in Superplasticity and Superplastic Forming, TMS, Warrendale, PA, 2004, pp. 9–20.
40. A. Goloborodko, T. Ito, X. Yun, Y. Motohashi, and G. Itoh: Mater. Trans., 2004, vol. 45, pp. 2503–08.10.2320/matertrans.45.2503 ↗
41. K.N. Krishnan: J. Mater. Sci., 2002, vol. 37, pp. 473–80.10.1023/A:1013701104029 ↗
42. K.A.A. Hassan, A.F. Norman, D.A. Price, and P.B. Prangnell: Acta Mater., 2003, vol. 51, pp. 1923–36.10.1016/S1359-6454(02)00598-0 ↗
43. M.M. Attallah and H.G. Salem: Mater. Sci. Eng., A, 2005, vol. 391, pp. 51–59.10.1016/j.msea.2004.08.059 ↗
44. A.A. Luo, R.C. Kubic, and J.M. Tartaglia: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2549–57.10.1007/s11661-003-0014-3 ↗
45. A. Turnbull and E.R.D. Rios: Fatigue Fract. Eng. Mater. Struct., 1995, vol. 18, pp. 1515–15.10.1111/j.1460-2695.1995.tb00874.x ↗
46. Y. Hong, Y. Qiao, N. Liu, and X. Zheng: Fatigue Fract. Eng. Mater. Struct., 1998, vol. 21, pp. 1317–25.10.1046/j.1460-2695.1998.00093.x ↗
47. N. Tsuji, S. Okuno, T. Matsuura, Y. Koizumi, and Y. Minamino: Thermec’ 2003, Pts 1–5, 2003, vol. 426 (4), pp. 2667–72.
48. R.S. Mishra, R.K. Islamgaliev, T.W. Nelson, Y. Hovansky, and M.W. Mahoney: Friction Stir Welding and Processing, TMS, Warrendale, PA, 2001, pp. 205–16.
49. Y.S. Sato, H. Watanabe, and H. Kokawa: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 318–23.10.1179/174329307X197575 ↗
50. Y.S. Sato, H. Kokawa, K. Ikeda, M. Enomoto, S. Jogan, and T. Hashimoto: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 941–48.10.1007/s11661-001-0351-z ↗
51. Y.C. Chen, J.C. Feng, and H.J. Liu: Mater. Charact., 2007, vol. 58, pp. 174–78.10.1016/j.matchar.2006.04.015 ↗
52. M. Karlsen, O. Frigaard, J. Hjelen, O. Grong, and H. Norum: Thermec’ 2003, Pts 1–5, 2003, vols. 426–432, pp. 2861–66.
53. F.J. Humphreys: Acta Mater., 1997, vol. 45, pp. 4231–40.10.1016/S1359-6454(97)00070-0 ↗
54. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier Science Ltd., Oxford, United Kingdom, 2004, pp. 1–6.
55. J.E. Burke and D. Turnbull: Prog. Met. Phys., 1952, vol. 3, pp. 220–92.10.1016/0502-8205(52)90009-9 ↗
56. R.D. Doherty, D.A. Hughes, F.J. Humphreys, J.J. Jonas, D.J. Jensen, M.E. Kassner, W.E. King, T.R. McNelley, H.J. McQueen, and A.D. Rollett: Mater. Sci. Eng., A, 1997, vol. 238, pp. 219–74.10.1016/S0921-5093(97)00424-3 ↗
57. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier Science Ltd., Oxford, United Kingdom, 2004, pp. 215–67.10.1016/B978-008044164-1/50011-6 ↗
58. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier Science Ltd., Oxford, United Kingdom, 2004, pp. 368–78.
59. P. Cotterill and P.R. Mould: Recrystallization and Grain Growth in Metals, 1st ed., John Wiley & Sons, New York, NY, 1976, pp. 292–325.
60. M. Cigdem: Z. Metallkd., 1994, vol. 85, pp. 723–32.
61. R.E. Reed-Hill and R. Abbaschian: Physical Metallurgy Principals, 3rd ed., PWS Publishing Company, Boston, MA, 1994, pp. 227–70.
62. D.J. Srolovitz, G.S. Grest, and M.P. Anderson: Acta Metall., 1985, vol. 33, pp. 2233–47.10.1016/0001-6160(85)90185-3 ↗
63. H.P. Longworth and C.V. Thompson: J. Appl. Phys., 1991, vol. 69, pp. 3929–40.10.1063/1.348452 ↗
64. I. Andersen, O. Grong, and N. Ryum: Acta Metall. Mater., 1995, vol. 43, pp. 2689–2700.10.1016/0956-7151(94)00489-5 ↗
65. F.J. Humphreys: Acta Mater., 1997, vol. 45, pp. 5031–39.10.1016/S1359-6454(97)00173-0 ↗
66. M. Hillert: Acta Metall., 1965, vol. 13, pp. 227–38.10.1016/0001-6160(65)90200-2 ↗
67. E. Nes, N. Ryum, and O. Hunderi: Acta Metall., 1985, vol. 33, pp. 11–22.10.1016/0001-6160(85)90214-7 ↗
68. J.S. Vetrano, S.M. Bruemmer, L.M. Pawlowski, and I.M. Robertson: Mater. Sci. Eng., A, 1997, vol. 238, pp. 101–07.10.1016/S0921-5093(97)00445-0 ↗
69. L. Dupuy, J.J. Blandin, and E.F. Rauch: Mater. Sci. Technol., 2000, vol. 16, pp. 1256–58.10.1179/026708300101507424 ↗
70. D.R. Herling and M.T. Smith: Ultrafine Grained Materials, TMS, Warrendale, PA, 2000, pp. 411–20.
71. Y.S. Sato, S.H.C. Park, and H. Kokawa: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 3033–42.10.1007/s11661-001-0178-7 ↗
72. Y.S. Sato, F. Yamashita, Y. Sugiura, S.H.C. Park, and H. Kokawa: Scripta Mater., 2004, vol. 50, pp. 365–69.10.1016/j.scriptamat.2003.10.008 ↗
73. Y.S. Sato, H. Takauchi, S.H.C. Park, and H. Kokawa: Mater. Sci. Eng., A, 2005, vol. 405, pp. 333–38.10.1016/j.msea.2005.06.008 ↗
74. J.R. Taylor, A.T. Dinsdale, M. Hillert, and M. Selleby: CALPHAD–Computer Coupling of Phase Diagrams and Thermochemistry, 1992, vol. 16, pp. 173–79.10.1016/0364-5916(92)90005-I ↗
75. L.F. Mondolfo: Aluminum Alloys: Structure and Properties, 1st ed., Butterworth Inc., Boston, MA, 1976, pp. 806–08.10.1016/B978-0-408-70932-3.50404-6 ↗
76. N.A. Belov, D.G. Eskin, and A.A. Aksenov: Multicomponent Phase Diagrams: Applications for Commercial Aluminum Alloys, 1st ed., Elsevier, San Diego, CA, 2005, pp. 47–48.10.1016/B978-008044537-3/50002-0 ↗
77. J.Z. Murray: J. Phase Equilib., 1998, vol. 19, pp. 368–75.10.1361/105497198770342102 ↗
78. Metals Handbook, 9th ed., ASM, Metals Park, OH, 1979, vol. 2, p. 104.
79. Handbook of Aluminum, 1st ed., CRC Press, New York, NY, 2003, vol. 1, pp. 120–25.
80. O. Hunderi, E. Nes, and N. Ryum: Acta Metall., 1989, vol. 37, pp. 129–33.10.1016/0001-6160(89)90272-1 ↗
81. K. Kannan, J.S. Vetrano, and C.H. Hamilton: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2947–57.10.1007/BF02663844 ↗
82. M.T. Perez-Prado, G. Gonzalez-Doncel, O.A. Ruano, and T.R. McNelley: Acta Mater., 2001, vol. 49, pp. 2259–68.10.1016/S1359-6454(01)00128-8 ↗
83. W. Gan, K. Okamoto, S. Hirano, K. Chung, C. Kim, and R.H. Wagoner: J. Eng. Mater.–Trans. ASME, 2008, vol. 130, pp. 031007-1–031007-15.
84. I. Charit and R.S. Mishra: Scripta Mater., 2008, vol. 58, pp. 367–71.10.1016/j.scriptamat.2007.09.052 ↗
85. J.R. Bradley and J.E. Carsley: Advances in Superplasticity and Superplastic Forming, TMS, Warrendale, PA, 2004, pp. 149–57.
86. K.T. Park, D.Y. Hwang, S.Y. Chang, and D.H. Shin: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2859–67.10.1007/s11661-002-0271-6 ↗
87. J.S. Vetrano, C.A. Lavender, C.H. Hamilton, M.T. Smith, and S.M. Bruemmer: Scripta Metall. Mater., 1994, vol. 30, pp. 565–70.10.1016/0956-716X(94)90430-8 ↗
88. R. Verma, A.K. Ghosh, S. Kim, and C. Kim: Mater. Sci. Eng., A, 1995, vol. 191, pp. 143–50.10.1016/0921-5093(94)09644-9 ↗
89. S. Agarwal, P.E. Krajewski, and C.L. Briant: Advances in Superplasticity and Superplastic Forming, TMS, Warrendale, PA, 2004, pp. 95–107.
90. J.R. Bradley: Advances in Superplasticity and Superplastic Forming, TMS, Charlotte, NC, 2004, pp. 109–18.
91. E.M. Taleff: Advances in Superplasticity and Superplastic Forming, TMS, Charlotte, NC, 2004, pp. 85–94.
92. M. Vulcan and K. Siegert: Advances in Superplasticity and Superplastic Forming, TMS, Charlotte, NC, 2004, pp. 351–60.
93. Machine Model: Hitachi GR-3DM10T, Hitachi America Ltd., Farmington Hills, MI.
94. D. Kim, H. Badarinarayan, J.H. Kim, C. Kim, K. Okamoto, R.H. Wagoner, and K. Chung: Eur. J. Mech. A–Solid, 2010, vol. 29, pp. 204–15.10.1016/j.euromechsol.2009.10.006 ↗
95. Metals Handbook, 9th ed., ASM, Metals Park, OH, 1979, vol. 2, pp. 28–29.
96. ASM Handbook, 6th ed., ASM INTERNATIONAL, Materials Park, OH, 1995, vol. 9, p. 354.
97. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier Science Ltd., Oxford, United Kingdom, 2004, pp. 541–56.
98. J.C. Russ and R.T. Dehoff: Practical Stereology, 2nd ed., Kluwer Academic/Plenum, New York, NY, 2000, pp. 1–18.10.1007/978-1-4615-1233-2 ↗
99. J.I. Goldstein, D.E. Newbury, P. Echlin, D.C. Joy, C. Fiori, and E. Lifshin: Scanning Electron Microscopy and X-Ray Microanalysis, 1st ed., Plenum Press, New York, NY, 1981, pp. 53–122.10.1007/978-1-4613-3273-2_3 ↗
100. R. Thomas: Practical Guide to ICP-MS, 1st ed., Marcel Dekker, New York, NY, 2003, pp. 180–87.10.1201/9780203027073 ↗