The influence of strontium on porosity formation in Al-Si alloys
Source abstract
Abstract
Strontium modification is known to alter the amount, characteristics, and distribution of porosity in Al-Si castings. Although many theories have been proposed to account for these effects, most can be considered inadequate because of their failure to resolve contradictions and discrepancies in the literature. In an attempt to critically appraise some of these theories, the amount, distribution, and morphology of porosity were examined in sand-cast plates of Sr-free and Sr-containing pure Al, Al-l wt pet Si, and Al-9 wt pet Si alloys. Statistical significance testing was used to verify apparent trends in the porosity data. No apparent differences in the amount, distribution, and morphology of porosity were observed between Sr-free and Sr-containing alloys with no or very small eutectic volume fractions. However, Sr modification significantly changed the amount, distribution, and morphology of porosity in alloys with a significant volume fraction of eutectic. ne addition of Sr reduced porosity in the hot spot region of the casting, and the pores became well dispersed and rounded. This result can be explained by considering the combined effect of the casting design and the differences in the pattern of eutectic solidification between unmodified and Sr-modified alloys.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. J.E. Gruzleski: AFS Trans., 1992, vol. 100, pp. 673–83.
2. H. Iwahori, K. Yonekura, Y. Yamamoto, and M. Nakamura: AFS Trans., 1990, vol. 98, pp. 167–73.
3. Q.T. Fang and D.A. Granger: AFS Trans., 1989, vol. 97, pp. 989–1000.
4. R. Fuoco, H. Goldenstein, and J.E. Gruzleski: AFS Trans., 1994, vol. 102, pp. 297–306.
5. J.P. Anson, J.E. Gruzleski, and M. Stucky: AFS Trans., 2001, vol. 109, pp. 3–18.
6. D. Argo and J.E. Gruzleski: AFS Trans., 1988, vol. 96, pp. 65–74.
7. M.O. Otte: Ph.D. Thesis, University of Queensland, Brisbane, 2000.
8. G.K. Sigworth, C. Wang, H. Huang, and J.T. Berry: AFS Trans., 1994, vol. 102, pp. 245–61.
9. S.D. McDonald, K. Nogita, A.K. Dahle, J.A. Taylor, and D.H. StJohn: AFS Trans., 2000, vol. 108, pp. 463–70.
10. A.K. Dahle, J.A. Taylor, and D.A. Graham: Aluminum Trans., 2000, vol. 3 (1), pp. 17–30.
11. A.K. Dahle, S.D. McDonald, and K. Nogita: in Materials Solutions 2002, ASM INTERNATIONAL, Columbus, OH, 2002, pp. 1–10.
12. J.E. Gruzleski and B.M. Closset: The Treatment of Liquid Aluminum-Silicon Alloys, American Foundrymen’s Society, Des Plaines, IL, 1990.
13. J. Campbell: in 4th Asian Foundary Congr., Australian Foundry Institute, Broadbeach, Queensland, Australia, 1996, pp. 33–50.
14. S. Fox and J. Campbell: Scripta Mater., 2000, vol. 43 (10), pp. 881–86.10.1016/S1359-6462(00)00506-6 ↗
15. F.C. Dimayuga, N. Handiak, and J.E. Gruzleski: AFS Trans., 1988, vol. 96, pp. 83–88.
16. M.H. Mulazimoglu, N. Handiak, and J.E. Gruzleski: AFS Trans., 1989, vol. 97, pp. 225–32.
17. D. Emadi, J.E. Gruzleski, and J.M. Toguri: Metall. Trans. B, 1993, vol. 24B, pp. 1055–63.10.1007/BF02660997 ↗
18. J.P. Anson, R.A.L. Drew, and J.E. Gruzleski: Metall. Mater. Trans. B, 1999, vol. 30B, pp. 1027–32.10.1007/s11663-999-0108-4 ↗
19. L. Liu, A.M. Samuel, F.H. Samuel, H.W. Doty, and S. Valtierra: J. Mater. Sci., 2003, vol. 38 (6), pp. 1255–67.10.1023/A:1022870006721 ↗
20. A.K. Dahle, J. Hjelen, and L. Arnberg: Proc. 4th Decennial Int. Conf. on Solidification Processing, Sheffield, 1997, pp. 527–30.
21. A.K. Dahle, K. Nogita, J.W. Zindel, S.D. McDonald, and L.M. Hogan: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 949–60.10.1007/s11661-001-0352-y ↗
22. K. Nogita and A.K. Dahle: Mater. Trans., 2001, vol. 42 (2), pp. 207–14.10.2320/matertrans.42.207 ↗
23. K. Nogita and A.K. Dahle: Mater. Trans., 2001, vol. 42 (3), pp. 393–96.10.2320/matertrans.42.393 ↗
24. K. Nogita and A.K. Dahle: Mater. Characterization, 2001, vol. 46 (4), pp. 305–10.10.1016/S1044-5803(00)00109-1 ↗
25. K. Nogita, S.D. McDonald, J.W. Zindel, and A.K. Dahle: Mater. Trans., 2001, vol. 42 (9), pp. 1981–86.10.2320/matertrans.42.1981 ↗
26. G. Heiberg and L. Arnberg: J. Light Met., 2001, vol. 1 (1), pp. 43–49.10.1016/S1471-5317(00)00005-5 ↗
27. L.F. Mondolfo: Aluminium Alloys: Structure and Properties, Butterworth and Co., London, 1976.
28. X.G. Chen, F.J. Klinkenberg, S. Engler, L. Heusler, and W. Schneider: JOM, 1994, vol. 46 (8), pp. 34–38.10.1007/BF03220773 ↗
29. J.A. Taylor: Ph.D. Thesis, University of Queensland, Brisbane, 1997.
30. R.P. Taylor, S.T. McClain, and J.T. Berry: Int. J. Cast Met., 1999, vol. 11, pp. 247–57.10.1080/13640461.1999.11819281 ↗
31. D.C. Montgomery, G.C. Runger, and N.F. Hubele: Eng. Statistics, 2nd ed., John Wiley, New York, NY, 2001.
32. W. Kurz and D.J. Fisher: Fundamentals of Solidification, 4th ed., Trans Tech Publications, Aedermannsdorf, Switzerland, 1998.
33. S.D. McDonald, Ph.D. Thesis, University of Queensland, Brisbane, 2002.
34. S.-Z. Lu and A. Hellawell: JOM, 1995, vol. 47 (2), pp. 38–40.10.1007/BF03221405 ↗