Cold-Cracking Assessment in AA7050 Billets during Direct-Chill Casting by Thermomechanical Simulation of Residual Thermal Stresses and Application of Fracture Mechanics
Source abstract
Abstract
Thermally induced strains and stresses developed during direct-chill (DC) semicontinuous casting of high strength aluminum alloys can result in formation of micro-cracks in different locations of the billet. Rapid propagation of such micro-cracks in tensile thermal stress fields can lead to catastrophic failure of ingots in the solid state called cold cracking. Numerical models can simulate the thermomechanical behavior of an ingot during casting and after solidification and reveal the critical cooling conditions that result in catastrophic failure, provided that the constitutive parameters of the material represent genuine as-cast properties. Application of fracture mechanics, on the other hand, can help to derive the critical crack length leading to failure. In the present research work, the state of residual thermal stresses was determined in an AA7050 billet during DC casting by means of ALSIM5. Simulation results showed that in the steady-state conditions, large compressive stresses form near the surface of the billet in the circumferential direction, whereas in the center, the stresses are tensile in all directions. Magnitudes of von Mises effective stresses, the largest component of principal stresses and the fracture mechanics concepts, were then applied to investigate the crack susceptibility of the billet.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. B. Hannart, F. Ciaalti, and R. van Schalkwijk: in Light Metals, U. Mannweiler, ed., TMS, Warrendale, PA, 1994, pp. 879–87.
2. M. Lalpoor, D.G. Eskin, and L. Katgerman: Mater. Sci. Eng., A, 2008, vol. 497, pp. 186–94.10.1016/j.msea.2008.06.047 ↗
3. J.M. Drezet and M. Rappaz: in Light Metals, J. Evans, ed., TMS, Warrendale, PA, 1995, pp. 941–50.
4. K.-M. Chang and B. Kang: J. Chin. Inst. Eng., 1999, vol. 22, pp. 27–42.10.1080/02533839.1999.9670439 ↗
5. H.G. Fjaer and A. Mo: in Light Metals, C.M. Bickert, ed., TMS, Warrendale, PA, 1990, pp. 945–50.
6. W. Boender, A. Burghardt, E.P. van Klaveren, and J. Rabenberg: in Light Metals, A.T. Tabereaux, ed., TMS, Warrendale, PA, 2004, pp. 679–84.
7. O. Ludwig, J.-M. Drezet, B. Commet, and B. Heinrich: in Modeling of Casting, Welding and Advanced Solidification Processes, MCWASP XI, C.-A. Gandin and M. Bellet, eds., TMS, Warrendale, PA, 2006, pp. 185–92.
8. W. Boender and A. Burghardt: Proc. 5th Decennial Int. Conf. on Solidification Processing, H. Jones, ed., University of Sheffield, Sheffield, United Kingdom, 2007, pp. 714–18.
9. J. Wan, H.M. Lu, K.M. Chang, and J. Harris: in Light Metals, B. Welch, ed., TMS, Warrendale, PA, 1998, pp. 1065–71.
10. K.-M. Chang, H.-M. Lu, and J. Wan: 2nd Int. Conf. on Quenching and Control of Diffusion, J.F. Harris, ed., ASM INTERNATIONAL, Materials Park, OH, 1996, pp. 341–45.
11. H.G. Fjaer and A. Mo: Metall. Trans. B, 1990, vol. 21B, pp. 1049–61.
12. E.E. Madsen and G.E. Fladmark: in Numerical Solution of Partial Differential Equations, G.E. Fladmark and J.G. Gram, eds., D. Reidel Publishing Company, Dordrecht, The Netherlands, 1973, pp. 223–40.10.1007/978-94-010-2672-7_9 ↗
13. E.E. Madsen: in Numerical Methods in Thermal Problems, R.W. Lewis and K. Morgan, eds., Pineridge Press Limited, Swansea, United Kingdom, 1979, pp. 81–89.
14. H. Fossheim and E.E. Madsen: in Light Metals, W.S. Peterson, ed., TMS-AIME, Warrendale, PA, 1979, pp. 695–720.
15. E.K. Jensen and W. Schneider: in Light Metals, C.M. Bickert, ed., TMS-AIME, Warrendale, PA, 1990, pp. 937–43.
16. M. Lalpoor, D.G. Eskin, and L. Katgerman: Proc. 12th Intern. Conf. on Fracture, Ottawa, National Research Council of Canada, 2009 (CD), pp. 1–9.
17. B. Magnin, L. Katgerman, and B. Hannart: Modeling of Casting, Welding and Solidification Process, MCWASP VII, M. Cross and J. Campbell, eds., TMS, Warrendale, PA, 1995, pp. 303–10.
18. C.L. Martin, O. Ludwig, and M. Suéry: Mater. Sci. Forum, 2002, vols. 396–402, pp. 265–70.
19. J. G. Kaufman: Properties of Aluminum Alloys; Tensile, Creep, and Fatigue Data at High and Low Temperatures, ASM INTERNATIONAL, Materials Park, OH, 2002, p. 207.
20. M. Lalpoor, D.G. Eskin, and L. Katgerman: Proc. Thermec 2009, Trans Tech Publications Ltd, Zürich, in press.
21. H. Tada, P.C. Paris, and G.R. Irwin: The Stress Analysis of Cracks Handbook, 3rd ed., ASME, New York, NY, 2000, Sect. 24.1, p. 342.10.1115/1.801535 ↗
22. D.P. Rooke and D.J. Cartwright: Compendium of Stress Intensity Factors, Her Majesty’s Stationery Office, London, 1976, Sect. 4.1.5, pp. 278–80.
23. V.A. Livanov: in Aluminum Alloys, A.F. Belov and G.D. Agarkov, eds., Oborongiz, Moscow, 1955, pp. 128–68.
24. J. B. Hess: Metall. Trans. A, 1983, vol. 14A, pp. 323–27.10.1007/BF02644210 ↗
25. S. Benum, D. Mortensen, H. Fjaer, H.-G. Øverlie, and O. Reiso: in Light Metals, W. Schneider, ed., TMS, Warrendale, PA, 2002, pp. 967–74.
26. R.K. Paramatmuni, K.M. Chang, B.S. Kang, and X. Liu: Mater. Sci. Eng. A, 2004, vol. 379, pp. 293–301.10.1016/j.msea.2004.02.026 ↗