Measuring Stress Distributions in Ti-6Al-4V Using Synchrotron X-Ray Diffraction
Source abstract
Abstract
This article presents a quantitative strain analysis (QSA) study aimed at determining the distribution of stress states within a loaded Ti-6Al-4V specimen. Synchrotron X-rays were used to test a sample that was loaded to a uniaxial stress of 540 MPa in situ in the A2 experimental station at the Cornell High Energy Synchrotron Source (CHESS). Lattice-strain pole figures (SPFs) were measured and used to construct a lattice strain distribution function (LSDF) over the fundamental region of orientation space for each phase. A high-fidelity geometric model of the experiment was used to drastically improve the signal-to-noise ratio in the data. The three-dimensional stress states at every possible orientation of each α (hcp) and β (bcc) crystal within the aggregate were calculated using the LSDF and the single-crystal moduli. The stress components varied by 300 to 500 MPa over the orientation space; it was also found that, in general, the crystal stress states were not uniaxial. The maximum shear stress resolved on the basal and prismatic slip systems of all orientations within the α phase, $$ \hat \tau _{{\text{rss}}} , $$ was calculated to illustrate the utility of this approach for better identifying “hard” and “soft” orientations within the loaded aggregate. Orientations with low values of $$ \hat \tau _{{\text{rss}}} , $$ which are potential microcrack initiation sites during dwell fatigue conditions, are considered hard and were subsequently illustrated on an electron backscatter diffraction (EBSD) map.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Titanium Alloys Microstructure and Properties · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. A.M. Korsunsky, K.E. Wells, and P.J. Withers: Scripta Metall., 1998, vol. 39, pp. 1705–1210.1016/S1359-6462(98)00385-6 ↗
2. A. Wanner, and D. Dunand: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 2949–6210.1007/BF02830344 ↗
3. M.P. Miller, J.V. Bernier, J.-S. Park, and A. Kazimirov: Rev. Sci. Instrum., 2005, vol. 76, p. 11390310.1063/1.2130668 ↗
4. S.F. Nielsen, A. Wolf, H.F. Poulsen, M. Ohler, U. Lienert, and R.A. Owen: J. Synchrotron Rad., 2000, vol. 7, pp. 103–0910.1107/S0909049500000625 ↗
5. E.M. Lauridsen, D. Juul Jensen, H.F. Poulsen, and U. Lienert: Scripta Mater., 2000, vol. 43, pp. 561–6610.1016/S1359-6462(00)00430-9 ↗
6. H.F. Poulsen, S.F. Nielsen, E.M Lauridsen, S. Schmidt, R.M. Suter, U. Lienert, L.F. Margulies, T. Lorentzen, and D. Juul Jensen: J. Appl. Crystallogr., 2001, vol. 34, pp. 751–5610.1107/S0021889801014273 ↗
7. L. Margulies, H.F. Poulsen, T. Lorentzen, and T. Leffers: Acta Mater., 2002, vol. 50 (7), pp. 1771–7910.1016/S1359-6454(02)00028-9 ↗
8. J.V. Bernier, and M.P. Miller: J. Appl. Crystallogr., 2006, vol. 39, pp. 358–6810.1107/S0021889806009873 ↗
9. J.V. Bernier, M.P. Miller, J.-S. Park, and U. Lienert: J. Eng. Mater. Technol., 2008, vol. 130, p. 02102110.1115/1.2870234 ↗
10. M.P. Miller, J.-S. Park, P.R. Dawson, and T.-S. Han: Acta Mater., 2008, vol. 56, pp. 3827–93910.1016/j.actamat.2008.04.062 ↗
11. I. Lonardelli, H.R. Wenk, L. Lutterotti, and M. Goodwin: J. Synchrotron Rad., 2005, vol. 12, pp. 354–6010.1107/S090904950500138X ↗
12. J.V. Bernier, M.P Miller, and D.E. Boyce: J. Appl. Crystallogr., 2006, vol. 39, pp. 697–71310.1107/S002188980602468X ↗
13. A. Kumar, and P.R. Dawson: Comput. Meth. Appl. Mech. Eng., 1998, vol. 153, pp. 259–30210.1016/S0045-7825(97)00072-8 ↗
14. J.F. Nye: Physical Properties of Crystals: Their Representation by Tensors and Matrices, Oxford University Press, New York, NY, 1985, pp. 280–81
15. H.-J. Bunge: Texture Analysis in Materials Science, Butterworths, London, 1982, p. 11910.1016/B978-0-408-10642-9.50010-6 ↗
16. A. Hammersley: The fit2d home page, 2005. Available at: http://www.esrf.eu/computing/scientific/FIT2D/
17. H.M. Rietveld: J. Appl. Crystallogr., 1969, vol. 2 pp. 65–7110.1107/S0021889869006558 ↗
18. The Rietveld Method, International Union of Crystallography—Monographs on Crystallography, R.A. Young, ed., Oxford University Press, New York, NY, 1995, p. 46
19. R.A. Young, and D.B. Wiles: J. Appl. Crystallogr., 1982, vol. 15, pp. 430–3810.1107/S002188988201231X ↗
20. R.L. Snyder: in The Rietveld Method, International Union of Crystallography—Monographs on Crystallography, R.A. Young, ed., Oxford University Press, New York, NY, 1995, pp. 139–47
21. G. Lutjering, and J. Williams: Titanium (Engineering Materials and Processes), Springer-Verlag, Berlin, 2003, pp. 17–21
22. C. Sarrazin, R. Chiron, S. Lesterlin, and J. Petit: Fatigue Fract. Eng. Mater. Struct., 1994, vol. 17 (12), pp. 1383–8910.1111/j.1460-2695.1994.tb00780.x ↗
23. M.R. Bache, W.J. Evans, and H.M. Davies: J. Mater. Sci., 1997, vol. 32, pp. 3435–4210.1023/A:1018624801310 ↗
24. V. Sinha, M.J. Mills, and J.C. Williams: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2015–2610.1007/s11661-006-0144-5 ↗
25. V. Sinha, M.J. Mills, and J.C. Williams: J. Mater. Sci., 2007, vol. 42, pp. 8334–4110.1007/s10853-006-0252-z ↗
26. A.P. Woodfield, M.D. Forman, R.R. Corderman, J.A. Sutliff, and B. Yamrom: in Titanium ’95: Science and Technology, P.A. Blenkinsop, W.J. Evans, and H.M. Flower, eds., The Institute of Materials, London, 1996, pp. 1116–23
27. F.P.E. Dunne, A. Walker, and D. Rugg: Proc. R. Soc. London, Ser. A, 2007, vol. 463, pp. 1467–8910.1098/rspa.2007.1833 ↗
28. T.-S. Han, and P.R. Dawson: Mater. Sci. Eng., A, 2005, vol. 405, pp. 18–3310.1016/j.msea.2005.05.095 ↗
29. R.A. Lebensohn: Acta Mater., 2001, vol. 49, p. 2723–3710.1016/S1359-6454(01)00172-0 ↗
30. J.-Y. Kim, V. Yakovlev, and S.I. Rokhlin: in CP615, Review of Quantitative Nondestructive Evaluation, D.O. Thompson and D.E. Chimenti, eds., American Institute of Physics, Melville, NY, 2002, vol. 21, pp. 1118–25