journal article·2012-06

Fiber Laser Welded AZ31 Magnesium Alloy: The Effect of Welding Speed on Microstructure and Mechanical Properties

S. H. Chowdhury, D. L. Chen, S. D. Bhole, E. Powidajko, D. C. Weckman, Y. Zhou

Publisher page

Abstract

This study was aimed at characterizing microstructural change and evaluating tensile and fatigue properties of fiber laser welded AZ31B-H24 Mg alloy with special attention to the effect of welding speed. Laser welding led to the formation of equiaxed dendrites in the fusion zone and columnar dendrites near the fusion zone boundary along with divorced eutectic Mg17Al12 particles and recrystallized grains in the heat-affected zone. The lowest hardness across the weld appeared in the fusion zone. Although the yield strength, ductility, and fatigue life decreased, the hardening capacity increased after laser welding, with a joint efficiency reaching about 90 pct. A higher welding speed resulted in a narrower fusion zone, smaller grain size, higher yield strength, and longer fatigue life, as well as a slightly lower strain-hardening capacity mainly because of the smaller grain sizes. Tensile fracture occurred in the fusion zone, whereas fatigue failure appeared essentially in between the heat-affected zone and the fusion zone. Fatigue cracks initiated from the near-surface welding defects and propagated by the formation of fatigue striations together with secondary cracks.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. T.M. Pollock: Science, 2010, vol. 328, pp. 986−87.10.1126/science.1182848 ↗
2. M. Wise, K. Calvin, A. Thomson, L. Clarke, B. Bond-Lamberty, R. Sands, S.J. Smith, A. Janetos, and J. Edmonds: Science, 2009, vol. 324, pp. 1183−86.10.1126/science.1168475 ↗
3. L.R. Kump: Nature, 2002, vol. 419, pp. 188−90.10.1038/nature01087 ↗
4. W.G. Agnew: Science, 1974, vol. 183, pp. 254−56.10.1126/science.183.4122.254 ↗
5. S. Begum, D.L. Chen, S. Xu, and A.A. Luo: Int. J. Fatigue, 2009, vol. 31, pp. 726−35.10.1016/j.ijfatigue.2008.03.009 ↗
6. S. Begum, D.L. Chen, S. Xu, and A.A. Luo: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 3014−26.10.1007/s11661-008-9677-0 ↗
7. K. Behler, J. Berkmanns, and A. Ehrhardt: Mater. Des., 1997, vol. 18, p. 261.10.1016/S0261-3069(97)00085-X ↗
8. E. Schubert, M. Klassen, and I. Zerner: J. Mater. Process. Technol., 2001, vol. 115, p. 2.10.1016/S0924-0136(01)00756-7 ↗
9. X. Cao, M. Jahazi, J.P. Immarigeon, and W. Wallace: J. Mater. Process. Technol., 2006, vol. 171, pp. 188−204.10.1016/j.jmatprotec.2005.06.068 ↗
10. A. Weisheit, R. Galun, and B.L. Mordike: Weld. J., 1998, vol. 77, pp. 149−54.
11. H. Zhao and T. DebRoy: Weld. J., 2001, vol. 80, pp. 204−10.
12. Z. Sun, D. Pan, and J. Wei: Sci. Technol. Weld. Joining, 2002, vol. 7, pp. 343−51.10.1179/136217102225006831 ↗
13. L. Quintino, A. Costa, R. Miranda, D. Yapp, V. Kumar, and C.J. Kong: Mater. Des., 2007, vol. 28, no. 4, pp. 1231−37.10.1016/j.matdes.2006.01.009 ↗
14. Y. Sakai, K. Nakata, T. Tsumura, M. Ueda, T. Ueyama, and K. Akamatsu: Mater. Sci. Forum, 2008, vols. 580−582, pp. 479−82.10.4028/www.scientific.net/MSF.580-582.479 ↗
15. J. Liu, J.H. Dong, and K. Shinozaki: Mater. Sci. Forum, 2009, vols. 610−613, pp. 911−14.10.4028/www.scientific.net/MSF.610-613.911 ↗
16. L. Yu, K. Nakata, and J. Liao: Sci. Technol. Weld. Joining, 2009, vol. 14, pp. 554−58.10.1179/136217109X441209 ↗
17. S.M. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, E. Powidajko, D.C. Weckman, and Y. Zhou: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 1974−89.10.1007/s11661-010-0574-y ↗
18. G.F. Vander Voort: Metallography Principles and Practice, ASM International, Materials Park, OH, 1999.
19. ASTM Standard E8/E8M: Standard Test Methods for Tension Testing of Metallic Materials, ASTM International, West Conshohohocken, PA, 2008.
20. N. Afrin, D.L. Chen, X. Cao, and M. Jahazi: Mater. Sci. Eng. A, 2008, vol. 472, pp. 179−86.10.1016/j.msea.2007.03.018 ↗
21. L.M. Liu, G. Song, and M.L. Zhu: Metall. Mater. Trans. A, 2008, vol. 39, pp. 1702−11.10.1007/s11661-008-9533-2 ↗
22. S.M. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, E. Powidajko, D.C. Weckman, and Y. Zhou: Mater. Sci. Eng. A, 2010, vol. 527, pp. 2951−61.10.1016/j.msea.2010.01.031 ↗
23. L. Xiao, L. Liu, D.L. Chen, S. Esmaeili, and Y. Zhou: Mater. Sci. Eng. A, 2011, vol. 529, pp. 81−87.10.1016/j.msea.2011.08.064 ↗
24. D. Gery, H. Long, and P. Maropoulos: J. Mater. Process. Technol., 2005, vol. 167, pp. 393−401.10.1016/j.jmatprotec.2005.06.018 ↗
25. N. Kishore Babu and M. Ashfaq: Pract. Metall., 2010, vol. 47, no. 8, pp. 426−42.10.3139/147.110097 ↗
26. C.H. Fan, Z.H. Chen, W.Q. He, J.H. Chen, and D. Chen: J. Alloys Compd., 2010, vol. 504, no. 2, pp. L42−45.10.1016/j.jallcom.2010.06.012 ↗
27. H.W. Wang, B. Li, J.C. Jie, and Z.J. Wei: Mater. Des., 2011, in press.
28. Y.H. Xiong, A.M. Yang, P.J. Li, and L. Liu: J. Aero. Mater., 2001, vol. 21, no. 4, pp. 5−8.
29. I. Gilath, J.M. Signamarcheix, and P. Bensussan: J. Mater. Sci., 1994, vol. 29, pp. 3358−62.10.1007/BF00356685 ↗
30. Y.J. Quan, Z.H. Chen, X.S. Gong, and Z.H. Yu: Mater. Charact., 2008, vol. 59, pp. 1491−97.10.1016/j.matchar.2008.01.010 ↗
31. S. Kou: Welding Metallurgy, 2nd ed., Wiley, New York, NY, 2003.10.1002/0471434027 ↗
32. L. Xiao, L. Liu, Y. Zhou, and S. Esmaeili: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1511−22.10.1007/s11661-010-0197-3 ↗
33. M.S. Turhal and T.S. Kan: J. Mater. Sci., 2003, vol. 38, pp. 2639−46.10.1023/A:1024434602540 ↗
34. M. Pareek, A. Polar, F. Rumiche, and J.E. Indacochea: J. Mater. Eng. Perform., 2007, vol. 16, pp. 655−62.10.1007/s11665-007-9084-5 ↗
35. R.C. Zeng, W. Dietzel, R. Zettler, J. Chen, and K.U. Kainer: Trans. Nonferrous Met. Soc. China, 2008, vol. 18, pp. S76−80.10.1016/S1003-6326(10)60178-1 ↗
36. G. Padmanaban, V. Balasubramanian, and J.K. Sarin Sundar: J. Mater. Eng. Perform., 2010, vol. 19, no. 2, pp. 155−65.10.1007/s11665-009-9389-7 ↗
37. X.Z. Lin and D.L. Chen: J. Mater. Eng. Perform., 2008, vol. 17, pp. 894−901.10.1007/s11665-008-9247-z ↗
38. J.A. Del Valle and O.A. Ruano: Scripta Mater., 2006, vol. 55, pp. 775−78.10.1016/j.scriptamat.2006.07.013 ↗
39. S.H.C. Park, Y.S. Sato, and H. Kokawa: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 987−94.10.1007/s11661-003-0228-4 ↗
40. N. Afrin, D.L. Chen, X. Cao, and M. Jahazi: Scripta Mater., 2007, vol. 57, pp. 1004−07.10.1016/j.scriptamat.2007.08.001 ↗
41. W.D. Callister Jr.: Materials Science and Engineering - An Introduction, 8th ed., Wiley, New York, NY, 2010.
42. J. Luo, Z. Mei, W. Tian, and Z. Wang: Mater. Sci. Eng. A, 2006, vol. 441, pp. 282−90.10.1016/j.msea.2006.08.051 ↗
43. J.H. Hollomon: Trans. AIME., 1945, vol. 162, pp. 268−89.
44. X.H. Chen and L. Lu: Scripta Mater., 2007, vol. 57, pp. 133−36.10.1016/j.scriptamat.2007.03.029 ↗
45. P. Ludwik: Elemente der Technologischen Mechanik, Springer-Verlag OHG, Berlin, Germany, 1909, p. 32.10.1007/978-3-662-40293-1 ↗
46. U.F. Kocks and H. Mecking: Progr. Mater. Sci., 2003, vol. 48, pp. 171−273.10.1016/S0079-6425(02)00003-8 ↗
47. J.A. Del Valle, F. Carreno, and O.A. Ruano: Acta Mater., 2006, vol. 54, pp. 4247−59.10.1016/j.actamat.2006.05.018 ↗
48. C.W. Sinclair, W.J. Poole, and Y. Brechet: Scripta Mater., 2006, vol. 55, pp. 739−42.10.1016/j.scriptamat.2006.05.018 ↗
49. I. Kovacs, N.Q. Chinh, and E. Kovacs-Csetenyi: Phys. Stat. Sol. A, 2002, vol. 194, pp. 3−18.10.1002/1521-396X(200211)194:1<3::AID-PSSA3>3.0.CO;2-K ↗
50. J. Balik, P. Lukac, Z. Drozd, and R. Kuzel: Int. J. Mater. Res., 2009, vol. 100, no. 3, pp. 322−25.10.3139/146.110042 ↗
51. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill, Columbus, OH, 1986.
52. G. Padmanaban and V. Balasubramanian: Mater. Des., 2010, vol. 31, pp. 3724−32.10.1016/j.matdes.2010.03.013 ↗
53. L.D. Scintilla, L. Tricarico, M. Brandizzib, and A.A. Satrianoc: J. Mater. Process. Technol., 2010, vol. 210, pp. 2206−14.10.1016/j.jmatprotec.2010.08.005 ↗
54. Y. Yu, C. Wang, X. Hu, J. Wang, and S. Yu: J. Mech. Sci. Technol., 2010, vol. 24, pp. 1077−82.10.1007/s12206-010-0309-4 ↗
55. K.S. Chan, Y.M. Pan, D.L. Davidson, and R.C. McClung: Mater. Sci. Eng. A, 1997, vol. 222, pp. 1−8.10.1016/S0921-5093(96)10395-6 ↗
56. C. Laird: Fatigue Crack Propagation, ASTM STP 415, 1967, pp. 131−68.10.1520/STP47230S ↗