journal article·2011-11

Grain Selection in Spiral Selectors During Investment Casting of Single-Crystal Components: Part II. Numerical Modeling

H. J. Dai, H. B. Dong, N. D’Souza, J.-C. Gebelin, R. C. Reed

Publisher page

Abstract

In this article, grain selection in spiral selectors during investment casting of single-crystal (SX) components is simulated using a cellular automaton grain structure model (CAFE) within a finite element thermal model (PROCAST). The models were validated against experimental observations and then were applied to model the effect of geometry of the spiral selectors on grain selection through a systematic approach. It was found that the efficiency of the spiral selector is significantly dependent on its geometry; the spiral becomes more efficient in selecting single grain with a smaller wax wire diameter; larger spiral rotation diameter, and smaller take-off angle. Recommendations for optimizing the spiral geometry are provided.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Solidification and crystal growth phenomena · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. H.J. Dai, N. D’Souza, and H.B. Dong: Metall. Mater. Trans. A, DOI:10.1007/s11661-011-0760-6.10.1007/s11661-011-0760-6 ↗
2. H.J. Dai, J.C. Gebelin, M. Newell, R.C. Reed, N. D’Souza, P.D. Brown, and H.B. Dong: Superalloys 2008, R.C Reed and K.A. Green, eds., Champion, PA, 2008, pp. 367–74.10.7449/2008/Superalloys_2008_367_374 ↗
3. H.J. Dai, J.-C. Gebelin, N. D’Souza, P.D. Brown, and H.B. Dong: Int. J. Cast Met. Res., 2008, vol. 22, pp. 54–57.10.1179/136404609X367317 ↗
4. H.J. Dai, H.B. Dong, H.V. Atkinson, and P.D. Lee: Solid State Phenomena, 2008, vol. 139, pp. 129–34.10.4028/www.scientific.net/SSP.139.129 ↗
5. N. Warnken, H. Larsson, and R.C. Reed: Mater. Sci. Technol., 2009, vol. 25, pp. 179–85.10.1179/174328408X369320 ↗
6. D. Pan, Q. Xu, B. Liu, J. Li, H. Yuan, and H. Jin: JOM, 2010, vol. 62, pp. 30–34.10.1007/s11837-010-0074-y ↗
7. S.-M. Seo, I.-S. Kim, J.-H. Lee, C.-Y. Jo, H. Miyahara, and K. Ogi: Met. Mater. Int., 2009, vol. 15, pp. 391–98.10.1007/s12540-009-0391-2 ↗
8. L. Beltran-Sanchez and D. Stefanescu: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2471–85.10.1007/s11661-006-0227-3 ↗
9. L. Yuan and P.D. Lee: Model. Simul. Mater. Sci. Eng., 2010, vol. 18, p. 055008.10.1088/0965-0393/18/5/055008 ↗
10. P. Carter, D.C. Cox, C.A. Gandin, and R.C. Reed: Mater. Sci. Eng. A, 2000, vol. 280, pp. 233–46.10.1016/S0921-5093(99)00701-7 ↗
11. H. Esaka, K. Shinozuka, and M. Tamura: Mater. Sci. Eng. A, 2005, vols. 413–414, pp. 151–55.10.1016/j.msea.2005.08.154 ↗
12. C.A. Gandin, J.L. Desbiolles, M. Rappaz, and P. Thevoz: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3153–65.10.1007/s11661-999-0226-2 ↗
13. C.A. Gandin, M. Rappaz, and R. Tintillier: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 629–35.10.1007/BF02651604 ↗
14. M. Rappaz and C.A. Gandin: Acta Mater., 1993, vol. 41, pp. 345–60.10.1016/0956-7151(93)90065-Z ↗
15. M.J. Goulette, P.D. Spilling, and R.P. Arthey: in Superalloys 1984, C.S. Kortovich and R.H. Bricknell, eds., TMS, Warrendale, PA, 1984, pp. 167–76.
16. P.A. Jennings: Rolls-Royce Plc., London, 1996.
17. H. J. Dai: Ph.D. Thesis, University of Leicester, Leicester, United Kingdom, 2009.
18. D.G. Eskin, Suyitno, and L. Katgerman: Progr. Mater. Sci., 2004, vol. 49, pp. 629–711.10.1016/S0079-6425(03)00037-9 ↗