journal article·2000-09

Development of a low-melting-point filler metal for brazing aluminum alloys

T. H. Chuang, L. C. Tsao, T. C. Tsai, M. S. Yeh, C. S. Wu

Publisher page

Abstract

The study is concerned with developing low-melting-point filler metals for brazing aluminum alloys. For this purpose, thermal analyses of a series of Al-Si-Cu-Sn filler metals have been conducted and corresponding microstructures observed. The results showed that the liquidus temperature of Al-Si-Cu filler metals dropped from 593 °C to 534 °C, when the amount of copper was increased from 0 to 30 pct. As the copper content reached further to 40 pct, the liquidus temperature would rise to 572 °C. By adding 2 pct tin into the Al-Si-20Cu alloys, the liquidus and solidus temperature would fall from 543 °C to 526 °C and from 524 °C to 504 °C, respectively. The main microstructures of Al-Si-Cu alloys consist of the α-Al solid solution, silicon particles, the CuAl2 (ϑ) intermetallic, and the eutectic structures of Al-Si, Al-Cu, and Al-Si-Cu. For further improvement of the brazability of this filler metal, magnesium was added as a wetting agent, which would remove the residual oxygen and moisture from the brazed aluminum surface and reduce the oxide film. Based on results gleaned from the thermal analyses, a new filler metal with the composition Al-7Si-20Cu-2Sn-1Mg is proposed, which possesses a melting temperature range of 501 °C to 522 °C and a microstructure that includes an Al-Si solid solution, silicon particles, a tin-rich phase, and CuAl2, CuMgAl2, and Mg2Si intermetallic compounds. When this filler metal was used to braze the 6061-T6 aluminum alloy, an optimized bonding strength of 196 ± 19 MPa was achieved.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Intermetallics and Advanced Alloy Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (9)

Show source-provided references
1. Y. Sugiyama: Weld. Int., 1989, No. 8, pp. 700–10.10.1080/09507118909446642 ↗
2. H. Kawase, T. Takemoto, M. Asano, I. Kawakatsu, and K. Liu: Weld. J., 1989, vol. 68, pp. 396s-403s.
3. T. Hattori, S. Sakai, A, Sakamoto, and C. Fujiwara: Weld. J., 1994, vol. 73, pp. 233s-240s.
4. G. Humpston, S.P.S. Sangha, and D.M. Jacobson: Mater. Sci. Technol., 1995, vol. 11, pp. 1161–67.10.1179/mst.1995.11.11.1161 ↗
5. D.M. Jacobson, G. Humpston, and S.P.S. Sangha: Weld. J., 1996, vol. 75, pp. 243s-250s.
6. K. Suzuki, M. Kagayama, and Y. Takeuchi: J. Jpn. Inst. Light Met., 1993, vol. 43 (10), pp. 533–38.10.2464/jilm.43.533 ↗
7. T. Kayamoto, J.H. Kim, S. Saito, and T. Onzawa: Proc. Workshop. J. Weld. Soc., 1994, vol. 12, pp. 495–501.
8. L.F. Mondolfo: Aluminum Alloys—Structure and Properties, Butterworth and Co., London, 1976, pp. 513–15.10.1016/B978-0-408-70932-3.50213-8 ↗
9. T. Osawa: Weld. J., 1995, vol. 74, pp. 206s-212s.