Microstructure and Fatigue Properties of a Friction Stir Lap Welded Magnesium Alloy
Source abstract
Abstract
Friction stir welding (FSW), being an enabling solid-state joining technology, can be suitably applied for the assembly of lightweight magnesium (Mg) alloys. In this investigation, friction stir lap welded (FSLWed) joints of AZ31B-H24 Mg alloy were characterized in terms of the welding defects, microstructure, hardness, and fatigue properties at various combinations of tool rotational rates and welding speeds. It was observed that the hardness decreased from the base metal (BM) to the stir zone (SZ) across the heat-affected zone (HAZ) and thermomechanically affected zone (TMAZ). The lowest value of hardness appeared in the SZ. With increasing tool rotational rate or decreasing welding speed, the average hardness in the SZ decreased owing to increasing grain size, and a Hall–Petch-type relationship was established. Fatigue fracture of the lap welds always occurred at the interface between the SZ and TMAZ on the advancing side where a larger hooking defect was present (in comparison with the retreating side). The welding parameters had a significant influence on the hook height and the subsequent fatigue life. A relatively “cold” weld, conducted at a rotational rate of 1000 rpm and welding speed of 20 mm/s, gave rise to almost complete elimination of the hooking defect, thus considerably (over two orders of magnitude) improving the fatigue life. Fatigue crack propagation was basically characterized by the formation of fatigue striations concomitantly with secondary cracks.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. T.M. Pollock: Science, 2010, vol. 328, pp. 986-87.10.1126/science.1182848 ↗
2. M. Wise, K. Calvin, A. Thomson, L. Clarke, B. Bond-Lamberty, R. Sands, S.J. Smith, A. Janetos, and J. Edmonds: Science, 2009, vol. 324, pp. 1183-86.10.1126/science.1168475 ↗
3. D. Shindell, G. Faluvegi, M. Walsh, S.C. Anenberg, R.V. Dingenen, N.Z. Muller, J. Austin, D. Koch, and G. Milly: Nat. Clim. Change, 2011, vol. 1, pp. 59-66.10.1038/nclimate1066 ↗
4. D.A. Howey: Nat. Clim. Change, 2012, vol. 2, pp. 28-29.10.1038/nclimate1336 ↗
5. S.J. Davis, K. Caldeira, and H.D. Matthews: Science, 2010, vol. 329, pp. 1330-33.10.1126/science.1188566 ↗
6. J. Murray, and D. King: Nature, 2012, vol. 481, pp. 433-35.10.1038/481433a ↗
7. L.R. Kump: Nature, 2002, vol. 419, pp. 188-90.10.1038/nature01087 ↗
8. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Church, P. Templesmith, and C.J. Dawes: GB Patent 9,125,978.9, 1991.
9. J.B. Jordon, J.B. Gibson, M.F. Horstemeyer, H.E. Kadiri, J.C. Baird, and A.A. Luo: Mater. Sci. Eng. A, 2011, vol. 528, pp. 6860-71.10.1016/j.msea.2011.05.047 ↗
10. Q. Yu, J. Zhang, Y. Jiang, and Q. Li: Inter. J. Fatigue, 2012, vol. 36, pp. 47-58.10.1016/j.ijfatigue.2011.08.016 ↗
11. S. Begum, D.L. Chen, S. Xu, and A.A. Luo: Mater. Sci. Eng. A, 2009, vol. A517, pp. 334-43.10.1016/j.msea.2009.04.051 ↗
12. H.Y. Wu, J.C. Yang, J.H. Liao, and F.J. Zhu: Mater. Sci. Eng. A, 2012, vol. 535, pp. 68-75.10.1016/j.msea.2011.12.043 ↗
13. H.Y. Wang, L.M. Liu, and Z.Y. Jia: J. Mater. Sci, 2011, vol. 46, pp. 5534-40.10.1007/s10853-011-5498-4 ↗
14. Q. Yu, J. Zhang, Y. Jiang, and Q. Li: Int. J. Fatigue, 2011, vol. 33, pp. 437-47.10.1016/j.ijfatigue.2010.09.020 ↗
15. C.L. Fan, D.L. Chen, and A.A. Luo: Mater. Sci. Eng. A, 2009, vol. A519, pp. 38-45.10.1016/j.msea.2009.04.048 ↗
16. X. Cao, and M. Jahazi: Materials and Design, 2009, vol. 30, pp. 2033-42.10.1016/j.matdes.2008.08.040 ↗
17. D. Fersini, and A. Pirondi : Eng. Fract. Mech., 2007, vol. 74, pp. 468-80.10.1016/j.engfracmech.2006.07.010 ↗
18. B.L. Mordike, and T. Ebert: Mater. Sci. Eng. A, 2001, vol. 30, pp. 37-45.10.1016/S0921-5093(00)01351-4 ↗
19. W.R. Oates, eds.: Welding Handbook, Materials and Applications, pt. 1, vol. 3, 8th ed., American Welding Society, Miami, FL, 1996, pp. 121–62.
20. K.G. Watkins: Magnesium Technology, Laser Welding of Magnesium Alloys, H.I. Kaplan, ed., TMS, The Minerals, Metals & Materials Society, Warrendale, PA, 2003.
21. ASM International: ASM Specialty Handbook, Magnesium and Magnesium Alloy, ASM International, 1999, pp. 94–199.
22. H. Zhao and T. Debroy: Welding Research Supplement, August 2001, pp. 204s–210s.
23. B.A. Mickucki and J.D. Shearhouse: Proceedings of Magnesium and Magnesium properties and Applications for Automobiles Conference, SAE Inc., Detroit, 1993, pp. 107–15.
24. K.H. Leong, G. Kornecki, P.G. Sanders, and J.S. Keske: Proceedings of ICALEO 1998, Laser Institute of America, Orlando, 1998, Section F, pp 28–36.
25. H.B. Chen, K. Yan, T. Lin, S.B. Chen, C.Y. Jiang, and Y. Zhao: Mater. Sci. Eng. A, 2006, vol. 433, pp. 64-69.10.1016/j.msea.2006.06.056 ↗
26. R.S. Mishra, and Z.Y. Ma: Mater. Sci. Eng. R, 2005, vol. 50, pp. 1-78.10.1016/j.mser.2005.07.001 ↗
27. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, R.A. Spurling, and W.H. Bingel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955-64.10.1007/s11661-998-0021-5 ↗
28. X. Cao and M. Jahazi: Proceedings of the 8th International Conference on “Trends in Welding Research”, S.A. David, T. DebRoy, J.N. DuPont, T. Koseki, and H.B. Smart, eds., ASM International, Materials Park, OH, 2009.
29. Q. Yang, X. Li, K. Chen, and Y.J. Shi: Mater. Sci. Eng. A, 2011, vol. 528, pp. 2463-78.10.1016/j.msea.2010.12.030 ↗
30. G.M.D. Cantin, S.A. David, W.M. Thomas, E. Lara-Curzio, and S.S. Babu: Sci. Technol. Weld Join., 2005, vol. 10, pp. 268-80.10.1179/174329305X39301 ↗
31. M. Ericsson, LZ. Jin, and R. Sandstrom: Int. J. Fatigue, 2007, vol. 29, pp. 57-68.10.1016/j.ijfatigue.2006.02.052 ↗
32. D. Fersini, and A. Pirondi: Eng Fract Mech, 2008, vol. 75, pp. 790-803.10.1016/j.engfracmech.2007.04.013 ↗
33. ASTM International Standard ASTM D3164-03: “Standard test method for strength properties of adhesively bonded lap-shear sandwich joints in shear by tensile loading”, 2003.
34. Y. Miyazaki and S. Furusako: Nippon Steel Technical Report No., 2007, vol. 95, pp. 28–34.
35. Draft International Standard ISO/DIS 25239-1.2: Friction stir welding-aluminum-part 1, vocabulary, 2009.
36. S.M. Chowdhury, D.L. Chen, S.D. Bhole, and X. Cao: Mater. Sci. Eng. A, 2010, vol. 527(21-22), pp. 6064-75.10.1016/j.msea.2010.06.012 ↗
37. T. Jene, G. Dobmann, G. Wagner, and D. Eifler: Proceedings of the 6th International Symposium on Friction Stir Welding, Montreal, Canada, 2006, pp. 1–6.
38. Y.S. Sato, F. Yamashita, Y. Sugiura, S.H.C. Park, and H. Kokawa: Scripta Mater, 2004, vol. 50, pp. 365-9.10.1016/j.scriptamat.2003.10.008 ↗
39. N. Afrin, D.L. Chen, X. Cao, and M. Jahazi: Mater. Sci. Eng. A, 2008, vol. 472, pp. 179-86.10.1016/j.msea.2007.03.018 ↗
40. S.H. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, and P. Wanjara: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 323–36.10.1007/s11661-012-1382-3 ↗
41. S.H. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, and P. Wanjara: Mater. Sci. Eng. A, 2012, vol. 556, pp. 500-509.10.1016/j.msea.2012.07.019 ↗
42. M. Fairman, N. Afrin, D.L. Chen, X.J. Cao, and M. Jahazi: Can. Metall. Q., 2007, vol. 46, 425-32.10.1179/000844307794557548 ↗
43. O. Frigaard, O. Grong, and O.T. Midling: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1189-99.10.1007/s11661-001-0128-4 ↗
44. Y.G. Kim, H. Fujji, T. Tsumura, T. Komazaki, and K. Nakata, Mater. Sci. Eng. A, 2006, vol. 415, pp. 250-54.10.1016/j.msea.2005.09.072 ↗
45. G.M. Cantin, S.A. David, E. Lara-Curzio, and S.S. Babu: Proceedings of the 8th International Conference on “Trends in Welding Research”, 2005, pp. 185–90.
46. L. Cederqvist and A.P. Reynolds: Weld J. (Res. Supplement), 2001, vol. 12, pp. 281–87.
47. X. Xu, X. Yang, G. Zhou, and J. Tong: Mater. Des., 2012, vol. 35, pp. 175-83.10.1016/j.matdes.2011.09.064 ↗
48. C. Laird: ASTM STP, 1967, vol. 415, pp. 131-68.
49. S. Begum, D.L. Chen, S. Xu, and A. A. Luo: Int. J. Fatigue, 2009, V31, pp. 726-35.10.1016/j.ijfatigue.2008.03.009 ↗
50. S. Begum, D.L. Chen, S. Xu, and A. A. Luo: Metall. Mater. Trans. A, 2008, vol. 39, pp. 3014-26.10.1007/s11661-008-9677-0 ↗