Influence of Cryoprocessing on Mechanism of Carbide Development in Cobalt-Bearing High-Speed Steel (M35)
Source abstract
Abstract
Cryogenic treatment has been used commonly to high-speed tool steels to enhance the wear resistance of the materials. In the current research study, specimens of complex alloyed high-speed tool steel (M35) were hardened at 1473 K (1200 °C), triple tempered at 673 K (400 °C) and then cryogenically treated at 88 K (−185 °C) for varying lengths of period starting from 16 to 48 hours of cryosoaking followed by soft tempering at 373 K (100 °C). These treated specimens were studied as a function of cryosoaking period for their electrical resistivity, residual compressive stress, and its correlation with carbide density was established. TEM analysis indicated carbide size 0.156 to 1 μm, which confirms that the cryogenic treatment enhances the precipitation of finer carbides. Lower residual stresses in the higher carbide density regimes identified in 2D contour map were explained by the stress relaxation in the matrix through precipitation of incoherent carbides.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · High Entropy Alloys Studies · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (10)
Show source-provided references
1. F.D. Silva, S.D. Franco, A.R. Machado, E.O. Ezugwu, and A.M. Souza: Wear, 2006, vol. 261, pp. 674–85.10.1016/j.wear.2006.01.017 ↗
2. J.Y. Huang, Y.T. Zhu, X.Z. Liao, I.J. Beyerlein, M.A. Bourke, and T.E. Mitchell: Mater. Sci. Eng., 2003, vol. 399A, pp. 241–44.10.1016/S0921-5093(02)00165-X ↗
3. I. Alexandru, G. Ailincai, and C. Baciu: J. of Meta., 1990, vol.4, pp. 283–388.
4. F. Meng, K. Tagashira, R. Azuma, and H. Soma: ISIJ International, 1994, vol. 34, pp. 205–10.10.2355/isijinternational.34.205 ↗
5. H. S. Yang, J. Wang, B. L. Shen, H.H. Liu, S.J. Gao, and S. J. Huang: Wear, 2006, vol. 261, pp.1150-54.10.1016/j.wear.2006.03.021 ↗
6. R. Kelkar, N. Philip, and Z. Yuntian: Heat Treat. Prog., 2007, pp. 55–60.10.4103/0301-4738.29516 ↗
7. D. Das, A.K. Dutta, and K.K. Ray: Cryogenics, 2009, vol. 49(5), pp. 176–84.10.1016/j.cryogenics.2009.01.002 ↗
8. N.B. Dhokey, and J.V. Dandawate: Trans. Indian Inst. Met., 2012, vol. 4, pp. 405–12.10.1007/s12666-012-0145-6 ↗
9. C. Gogte, D. Peshwe, A. Likhite and S. Lomte: Adv. Mater. Res., 2012, pp 383–90.10.4028/www.scientific.net/AMR.383-390.7138 ↗
10. N.B. Dhokey, J. Dandawate, H. Gangurde, and A. Harle: Eng. Fail. Anal., 2011, vol. 21, pp. 52–58.10.1016/j.engfailanal.2011.11.013 ↗