journal article·2006-12

The effect of friction stir processing on 5083-H321/5356 Al arc welds: Microstructural and mechanical analysis

Christian B. Fuller, Murray W. Mahoney

Publisher page

Abstract

Friction stir processing (FSP) is used locally to modify the microstructure and thus mechanical properties of 5083-H321/5356 aluminum gas metal arc welds (GMAWs). Four specimen approaches were examined: as-arc welded, weld toe FSP (with arc weld on either the advancing or the retreating side of tool), and weld crown FSP. Microstructures within the fine-grained FSP region contained smaller constituent particles. Mg2Si and Al6(Fe,Mn), than those particles found in the arc weld nugget, heat-affected zone (HAZ), and base-metal (BM) locations. The FSP improved the monotonic tensile strength, yield strength, and elongation of 5083-H321/5356 Al arc welds by 6 to 9 pct, 7 to 13 pct, and 46 to 80 pct, respectively. The addition of FSP produced a 30 pct increase in the load necessary to reach 107 cycles during four-point bending fatigue. An analysis of strengthening mechanisms determined that solid-solution, grain-size, and precipitation strengthening made contributions to the calculated yield strength of the BM, are weld nugget, and FSP regions. In addition, the strength mechanism analysis demonstrated that FSP increased the amount of grain-size strengthening and precipitate strengthening by nearly 110 MPa, when compared to the arc weld nugget.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. W.W. Sanders, Jr. and F.V. Lawrence, Jr.: Fatigue Behavior of Aluminum Alloy Weldments, ASTM STP 648. ASTM, Philadelphia, PA, 1978, p. 22.
2. U. Brandt, F.V. Lawrence, and C.M. Sonsino: Fatigue Fract. Eng. Mater. Struct., 2001, vol. 24, p. 117.10.1046/j.1460-2695.2001.00372.x ↗
3. P.G. Forrest: Fatigue of Metals, Pergamon Press, Oxford, United Kingdom, 1962, p. 280.
4. T.R. Gurney: Fatigue of Welded Structures, Cambridge University Press, Cambridge, United Kingdom, 1971, p. 215.
5. R.P. Newman: Br. Welding J., 1959, vol. 6, p. 324.
6. P. Prevey and M. Mahoney: Mater. Sci. Forum, 2003, vols. 426–32, p. 2933.10.4028/www.scientific.net/MSF.426-432.2933 ↗
7. J.L. Wood: Br. Welding J., 1960, vol. 7, p. 365.
8. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Templesmith, and C.J. Dawes: U.S. Patent No. 5,460,317, Oct. 24, 1995.
9. P.J. Haagensen, M. Ranes, A.O. Kluken, and I. Kvale: Mater. Eng., 1996, vol. 3, p. 505.
10. W.J. Arbegast and P.J. Hartley: U.S. Patent No. 6,230,957, May 15, 2001.
11. M. Mahoney, R.S. Mishra, T. Nelson, J. Flintoff, R. Islamgaliev, and Y. Hovansky: in Friction Stir Welding and Processing, K.V. Jata, M.W. Mahoney, R.S. Mishra, S.L. Semiatin, and D.P. Field, eds., TMS, Warrendale, PA, 2001, p. 183.
12. M.P. Miles, M.W. Mahoney, T.W. Nelson, and R.S. Mishra: in Friction Stir Welding and Processing II, K.V. Jata, M.W. Mahoney, R.S. Mishra, S.L. Seniatin, and T. Lienert, eds., TMS, Warrendale, PA, 2003, p. 253.
13. M.W. Mahoney, W.H. Bingel, S.R. Sharma, and R.S. Mishra: Mater. Sci. Forum, 2003, vols. 426–32, p. 2843.10.4028/www.scientific.net/MSF.426-432.2843 ↗
14. Z.Y. Ma, S.A. Shaarma, R.S. Mishra, and M.W. Mahoney: Mater. Sci. Forum, 2003, vols. 426–32, p. 2891.10.4028/www.scientific.net/MSF.426-432.2891 ↗
15. S.P. Lynch, D.P. Edwards, A. Majumdar, S. Moutsos, and M.W. Mahoney: Mater. Sci. Forum, 2003, vols. 426–32, p. 2903.10.4028/www.scientific.net/MSF.426-432.2903 ↗
16. C.J. Sterling, T.W. Nelson, C.D. Sorensen, and M. Posada: BYU, Provo, UT, unpublished research, 2004.
17. M. Fahrmann, P. Fratzl, P. Paris, E. Fahrmann, and W.C. Johnson: Acta Metall. Mater., 1995, vol. 43, p. 1007.10.1016/0956-7151(94)00337-H ↗
18. L.F. Mondolfe: Aluminum Alloys: Structure and Properties, Butterworth and Co., London, 1976, p. 808.
19. K. Kannan, C.H. Hohnson, and C.H. Hamilton: Metall. Mater. Trans. A, 1998, vol. 29, p. 1211.10.1007/s11661-998-0248-1 ↗
20. H.B. McShane, C.P. Lee, and T. Sheppard: Mater. Sci. Technol., 1990, vol. 6, p. 428.10.1179/mst.1990.6.5.428 ↗
21. Y.S. Sato, S.H.C. Park, and H. Kokawa: Metall. Mater. Trans. A. 2001, vol. 32, p. 3033.10.1007/s11661-001-0178-7 ↗
22. Aluminum Standards and Data, The Aluminum Association, Washington DC, 2000, p. 2–2.
23. B. London, M. Mahoney, W. Bingel, M. Calabrese, R. Bossi, and D. Waldron: in Friction Stir Welding and Processing II, K.V. Jata, M.W. Mahoney, R.S. Mishra, S.L. Semiatin, and T. Lienert, eds., TMS, Marrendale, PA, 2003, p. 3.
24. C.B. Fuller, A.R. Krause, D.C. Dunand, and D.N. Seidman: Mater. Sci. Eng. A. 2002, vol. 338, p. 8.10.1016/S0921-5093(02)00056-4 ↗
25. K.A.A. Hassan, B.P. Wynne, and P.B. Prangnell: Proc. 4th Int. Symp. on Friction Stir Welding, Park City, UT, TWI, Cambridge, United Kingdom, 2003.
26. A.A. Nayeb-Hashemi and J.B. Clark: in Binary Alloy Phase Diagrams, T.B. Massalaski, J.L. Murray, L.H. Bennett, and H. Baker, eds., ASM INTERNATIONAL, Metals Park, OH, 1986, vol. 2, p. 1544.
27. J.L. Murray: in Binary Alloy Phase Diagrams, T.B. Massalaski, J.L. Murray, L.H. Bennett, and H. Baker, eds., ASM INTERNATIONAL, Metals Park, OH, 1986, vol. 1, p. 129.
28. C.B. Fuller: Rockwell Scientific Inc., Thousand Oaks, CA, unpublished research, 2004.
29. T. Shinoda and M. Kawai: Mater. Sci. Forum, 2003, vols. 426–32, p. 2837.10.4028/www.scientific.net/MSF.426-432.2837 ↗
30. P.B. Hirsch and F.J. Humphreys: The Physics and Strength of Plasticity, A. Argon, ed., MIT Press, Cambridge, MA, 1969, p. 189.
31. M.A. Meyers and K.K. Chawla: Mechanical Metallurgy: Principles and Applications, Paramus, Englewood Cliffs, NJ, 1984.
32. L.M. Brown and R.K. Ham: in Strengthening Methods in Crystals, A. Kelly and R.B. Nicholson, eds., Elsevier, Amsterdam, 1971, p. 9.
33. P.M. Kelly: Met. Forum. 1982, vol. 5, p. 13.
34. L.-A. Norstrom: Scand. J. Metall., 1976, vol. 5, p. 159.
35. H.R. Last and R.K. Garret, Jr.: Metall. Mater. Trans. A, 1996, vol. 27, p. 737.10.1007/BF02648961 ↗
36. R.O. England, J.R. Pickens, K.S. Kumar, and T.J. Langan: in Dispersion Strengthened Aluminum Alloys, Y.-W. Kim and W.M. Griffith, eds., TMS, Warrendale, PA, 1988, p. 371.
37. S.A. Court, K.M. Gatenby, and D.J. Lloyd: Mater. Sci. Eng., A, 2001, vols. 319–21, p. 443.10.1016/S0921-5093(00)02018-9 ↗
38. D. Hull and D.J. Bacon: Introduction to Dislocations, 3rd ed., Butterworth-Heinemann, Oxford United Kingdom, 1997, p. 240.
39. H.J. Frost and M.F. Ashby: Deformation-Mechanism Maps: The Plasticity and Creep of Metals and Ceramics, Pergamon Press, Oxford, United Kingdom, 1982, p. 26.
40. S.L. Semiatin, K.V. Jata, M.D. Uchic, P.B. Berbon, D.E. Matejezyk, and C.C. Bampton: Scripta Mater., 2001, vol. 44, p. 395.10.1016/S1359-6462(00)00612-6 ↗
41. V.L. Tellkamp, A. Melmed, and E.J. Lavernia: Metall. Mater. Trans. A, 2001, vol. 32, p. 2335.10.1007/s11661-001-0207-6 ↗