journal article·2009-08

Formability Analysis of Diode-Laser-Welded Tailored Blanks of Advanced High-Strength Steel Sheets

S.K. Panda, V.H. Baltazar Hernandez, M.L. Kuntz, Y. Zhou

Publisher page

Abstract

Currently, advances due to tailored blanking can be enhanced by the development of new grades of advanced high-strength steels (HSSs), for the further weight reduction and structural improvement of automotive components. In the present work, diode laser welds of three different grades of advanced high-strength dual-phase (DP) steel sheets (with tensile strengths of 980, 800, and 450 MPa) to high-strength low-alloy (HSLA) material were fabricated by applying the proper welding parameters. Formability in terms of Hecker’s limiting dome height (LDH), the strain distribution on the hemispherical dome surface, the weld line movement during deformation, and the load-bearing capacity during the stretch forming of these different laser-welded blanks were compared. Finite element (FE) analysis of the LDH tests of both the parent metals and laser-welded blanks was done using the commercially available software package LS-DYNA (Livermore Software Technology Corporation, Livermore, CA); the results compared well with the experimental data. It was also found that the LDH was not affected by the soft zone or weld zone properties; it decreased, however, with an increase in a nondimensional parameter, the “strength ratio” (SR). The weld line movement during stretch forming is an indication of nonuniform deformation resulting in a decrease in the LDH. In all the dissimilar weldments, fracture took place on the HSLA side, but the fracture location shifted to near the weld line (at the pole) in tailor-welded blanks (TWBs) of a higher strength ratio.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Laser and Thermal Forming Techniques · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Advanced High Strength Steel Application Guidelines, version 4, World Auto Steel, March 2009, www.worldautosteel.org.
2. Auto/Steel Partnership: Tailor Welded Blank Design and Manufacturing Manual, Technical Report, 1995.
3. B. Kinsey, Z. Liu, and J. Cao: J. Mater. Process. Technol., 2000, vol. 99, pp. 145–53.10.1016/S0924-0136(99)00412-4 ↗
4. C.H. Cheng, M. Jie, C.L. Chan, and C.L. Chow: Int. J. Mech. Sci., 2007, vol. 49, pp. 217–29.10.1016/j.ijmecsci.2006.08.012 ↗
5. N. Sreenivasan, M. Xia, S. Lawson, and Y. Zhou: J. Eng. Mater. Technol. (Trans. ASME), 2008, vol. 130 (4), 041004.10.1115/1.2969246 ↗
6. M. Xia, N. Sreenivasan, S. Lawson, and Y. Zhou: J. Eng. Mater Technol. (Trans. ASME), 2007, vol. 129, pp. 446–52.10.1115/1.2744417 ↗
7. S.K. Panda, N. Sreenivasan, M. Kuntz, and Y. Zhou: J. Eng. Mater. Technol. (Trans. ASME), 2008, vol. 130 (4), 041003.10.1115/1.2969256 ↗
8. S.K. Panda, D. Ravi Kumar, H. Kumar, and A.K. Nath: J. Mater. Process. Technol., 2007, vol. 183, pp. 321–32.10.1016/j.jmatprotec.2006.10.035 ↗
9. D. Dry, W. Wadell, and D.R.J. Owen: Sci. Technol. Weld. Join., 2002, vol. 7 (1), pp. 11–18.10.1179/136217101125000523 ↗
10. G. Kridli, P.A. Friedman, and A.M. Sherman: SAE Technical Paper No. 2000-01-0772, SAE, Detroit, Michigan, March 6–9, 2000, pp. 1–9.
11. L.C. Chan, S.M. Chan, C.H. Cheng, and T.C. Lee: J. Eng. Mater. Technol., 2005, vol. 127, pp. 179–85.10.1115/1.1857936 ↗
12. Y. Choi, Y. Heo, H.Y. Kim, and D. Seo: J. Mater. Process Technol., 2000, vol. 108, pp. 1–7.10.1016/S0924-0136(00)00536-7 ↗
13. Y. Heo, Y. Choi, H. Kim, and D. Seo: J. Mater. Process. Technol., 2001, vol. 111, pp. 164–69.10.1016/S0924-0136(01)00503-9 ↗
14. S.K. Panda and D. Ravi Kumar: J. Mater. Process. Technol., 2008, vol. 204, pp. 70–79.10.1016/j.jmatprotec.2007.10.076 ↗
15. S. Gaied, J. Roelandt, F. Pinard, F. Schmit, and M. Balabane: J. Mater. Process. Technol., 2009, vol. 209, pp. 387–95.10.1016/j.jmatprotec.2008.02.031 ↗
16. H. Shao, J. Gould, and C. Albright: Metall. Mater. Trans. B, 2007, vol. 38B, pp. 321–31.10.1007/s11663-007-9026-5 ↗
17. S.S. Hecker: Met. Eng. Q., 1974, pp. 30–36.10.1530/jrf.0.0360485-a ↗
18. K. Narasimhan and V.M. Nadedkar: Trans. Ind. Inst. Met., 1996, vol. 49, pp. 659–76.
19. N. Yurioka, H. Suzuki, S. Ohshita, and S. Saito: Weld. J., 1980, vol. 62, pp. 147s–153s.
20. F.M. Al-Abbasi and J.A. Nemes: Int. J. Solid. Struct., 2003, vol. 40, pp. 3379–91.10.1016/S0020-7683(03)00156-2 ↗
21. D.V. Wilson: Metall. Technol., 1980, vol. 7, pp. 282–92.10.1179/030716980803287297 ↗
22. S.K. Panda, M.L. Kuntz, and Y. Zhou: Sci. Technol. Weld. Join., 2009, vol. 14, pp. 52–61.10.1179/136217108X343920 ↗
23. R.W. Davies, G.J. Grant, M.A. Khaleel, M.T. Smith, and H. Eddie Oliver: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 275–83.10.1007/s11661-001-0259-7 ↗
24. J.O. Hallquist: LS-DYNA Keyword User’s Manual, Version 970, 2003, http://www.lstc.com/(Registered trademark of Livermore Software Technology Corporation, Livermore, CA).
25. W. Bleck, Z. Deng, K. Papamantellos, and C.O. Gusek: J. Mater. Process. Technol., 1998, vol. 83, pp. 223–30.10.1016/S0924-0136(98)00066-1 ↗
26. T. Belytschko, J.I. Lin, and C. Tsay: Comput. Methods Appl. Mech. Eng., 1984, vol. 42, pp. 225–51.10.1016/0045-7825(84)90026-4 ↗
27. A.K. Ghosh: Int. J. Mech. Sci., 1977, vol. 19, pp. 457–70.10.1016/0020-7403(77)90019-4 ↗
28. F. Barlat and J.I. Lian: Int. J. Plast., 1989, vol. 5, pp. 51–56.10.1016/0749-6419(89)90019-3 ↗
29. M. Xia, E. Biro, Z. Tian, and Y. Zhou: ISIJ Int., 2008, vol. 48, pp. 809–14.10.2355/isijinternational.48.809 ↗
30. V.H. Baltazar Hernandez, M.L. Kuntz, M.I. Khan, and Y. Zhou: Sci. Technol. Weld. Join., 2008, vol. 13, pp. 769–76.10.1179/136217108X325470 ↗
31. N. Sreenivasan, M. Kuntz, and Y Zhou: Int. Conf. Mater. Sci. Technol. (MS&T) Automotive, Detroit, MI, 2007, pp. 267–80.
32. S.K. Panda: Doctoral Thesis, Indian Institute of Technology, Delhi, India, 2007, chap. 6, pp. 112–61.