journal article·2003-08

Hot working and recrystallization of As-Cast 316L

Martin C. Mataya, Eric R. Nilsson, Elliot L. Brown, George Krauss

Publisher page

Abstract

Stress-strain behavior and microstructure evolution during hot working of as-cast austenitic stainless steel alloy 316L were investigated by uniaxial compression of cylindrical specimens at a strain rate of 1 s−1 over the temperature range 1000 °C to 1150 °C and up to a strain of one. The measured flow curves showed monotonic hardening, indicating that dynamic recrystallization was not important in microstructural evolution. Static recrystallization was observed to nucleate preferentially at the delta ferrite-austenite interphase boundaries. The recrystallization kinetics of the as-cast material was compared to a relatively fine-grained wrought 316L material and found to be somewhat slower. However, the difference between the two material conditions was not nearly as great as previously reported for as-cast and wrought 304L alloy. The difference in behaviors between 316L and 304L is attributed to the relatively large amount and vermicular morphology of the delta ferrite phase in the 316L, resulting in a relatively fine effective grain size, compared to the existing coarse columnar structure, and concomitant enhancement of recrystallization. Compared to wrought 316L, the recrystallization rate of the as-cast material was relatively sluggish, despite a relatively fine effective grain size. The difference is associated with the 100 orientations of the columnar grains with respect to the compression axis, producing a soft orientation and a reduced rate of accumulation of dislocation density in the substructure. Also, compared to wrought 316L, the recrystallization rate of the as-cast material tends to decrease with time, the drop occurring concurrently with spheroidization and dissolution of the ferrite. It is suggested that (1) movement of the delta ferrite-austenite interphase boundary during spheroidization may poison incipient recrystallization and (2) dissolution of delta ferrite can locally enrich the austenite matrix in Mo and Cr, raising the local stacking fault energy and lowering grain boundary mobility to favor recovery over recrystallization in the vicinity of the ferrite-austenite boundary. A kinetic model for recrystallization was developed and used to simulate evolution of the first cycle of recrystallization during various thermal-mechanical treatment schedules typically employed during the primary breakdown of as-cast material.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. H.J. McQueen and J.J. Jonas: J. Appl. Metalworking, 1984, vol. 3 (3), pp. 233–41.10.1007/BF02833651 ↗
2. W. Roberts: in Deformation, Processing and Structure, G. Krauss, ed., ASM, Metals Park, OH, 1984, pp. 109–84.
3. W. Roberts, H. Boden, and B. Ahlblom: Met. Sci., 1979, Mar.–Apr., pp. 195–205.10.1179/msc.1979.13.3-4.195 ↗
4. M.C. Mataya, M.L. Robinson, D. Chang, M.J. Weis, G.R. Edwards, and D.K. Matlock: 29th Mechanical Working and Steel Processing Conf. Proc., ISS-AIME, Toronto, ON, Canada, 1987, vol. XXV, pp 235–248.
5. S.L. Semiatin, G.D. Lahoti, and T. Altan: Process Modeling-Fundamentals and Applications to Metals, ASM, Metals Park, OH, 1980, pp 387–408.
6. G.T. Campbell, JR., E.P. Abrahamson, and N.J. Grant: Metall. Trans., 1974, vol. 5, pp. 1875–81.10.1007/BF02644154 ↗
7. R.H. Kane: in The Hot Deformation of Austenite, J.B. Balance, ed., AIME, New York, NY, 1977, pp. 457–498.
8. N.D. Ryan and H.J. McQueen: New Developments in Stainless Steel Technology, ASM, Metals Park, OH, 1985, pp. 293–304.
9. E.R. Nilsson: Master’s Thesis, Colorado School of Mines, Golden, CO, 2000.
10. M.C. Mataya and V.E. Sackschewsky: Metall. Trans. A, 1994, vol. 25A, pp. 2737–52.10.1007/BF02649226 ↗
11. D.J. Long and W.T. Delong: Welding J., 1973, vol. 52, (7), pp. 281s-297s.
12. D. Kotecki and T.A. Siewert: Welding J., 1992, vol. 71 (5), pp. 171s-179s.
13. E.L. Brown: in Materials Studies for Magnetic Fusion Energy Applications at Low Temperatures—IV, National Bureau of Standards, Boulder, CO, 1981, pp. 357–414.
14. E.F. Boultbee and G.A. Schofield: Typical Microstructures of Cast Metals, Institute of British Foundrymen Publications, Birmingham, England, 1981, pp. 210–15.
15. K. Kuo: J. Iron Steel Inst., 1954, Apr., pp. 433–41.
16. N. Suutala: Metall. Trans. A, 1982, vol. 14A, pp. 191–97.
17. O. Hammer and U. Svennson: Solidification and Casting of Metals, The Metals Society, London, 1979, pp. 401–10.
18. N.D. Ryan, H.J. McQueen, and J.J. Jonas: Can. Metall. Q., 1983, vol. 22 (3), pp. 369–78.10.1179/cmq.1983.22.3.369 ↗
19. S.A. Saltykov: in Stereology, H. Elias, ed., Springer-Verlag, New York, NY, 1967.
20. B. Weiss and R. Stickler: Metall. Trans., 1972, vol. 3, pp. 851–66.10.1007/BF02647659 ↗
21. K.W. Andrews, D.J. Dyson, and S.R. Keown: Interpretation of Electron Diffraction Patterns, Plunum Press, New York, NY, 1971.
22. J.W. Edington: Practical Electron Microscopy in Materials Science, Van Nostrand Reinhold, 1976.
23. G. Kurdjumov and G. Sachs: Z. Phys., 1930, vol. 64, pp. 325–43.10.1007/BF01397346 ↗
24. Z. Nishiyama: Sci. Rep. Res. Inst., Tohoku Univ., 1934, vol. 23, pp. 637–64.
25. G. Wasserman: Arch. Eisenhuttenwes., 1933, vol. 16, p. 647.
26. T.J. Headley and J.A. Brooks: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 5–15.10.1007/s11661-002-0001-0 ↗
27. E.L. Brown, T. Whipple, and G. Krauss: Duplex Stainless Steels, ASM, Metals Park, OH, 1980.
28. A. Pinol-Juez, A. Iza-Mendia, and I. Gutierrez: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1671–77.10.1007/s11661-000-0177-0 ↗
29. D. R. Barraclough and C.M. Sellars: Metal Sci., 1979, Mar.–Apr., pp. 257–67.10.1179/msc.1979.13.3-4.257 ↗
30. J.P. Sah, G.J. Richardson, and C.M. Sellars: Metal Sci., 1974, vol. 8, pp. 325–31.10.1179/msc.1974.8.1.325 ↗
31. M.C. Mataya, E.R. Nilsson, and G. Krauss: in Superalloys 718, 625, 706, and Various Derivatives, E.A. Loria, ed., TMS, Warrendale, PA, 1994, pp. 331–43.10.7449/1994/Superalloys_1994_331_343 ↗
32. M.C. Mataya: J. Met., 1999, vol. 51 (1), pp. 18–26.
33. M.C. Mataya and D.K. Matlock: in Superalloy 718, Metallurgy and Applications, E.A. Loria, ed., TMS, Warrendale, PA, 1989, pp. 155–78.10.7449/1989/Superalloys_1989_155_178 ↗
34. A.R. Jones: J. Mater. Sci., 1981, vol. 16, pp. 1374–80.10.1007/BF01033854 ↗
35. J. Huber and M. Hatherly: Met. Sci., 1979, vol. 13, pp. 665–69.10.1016/0036-9748(79)90132-7 ↗
36. H. Hu, B.B. Rath, and R.A. Vandermeer: in Recrystallization ’90, T Chandra, ed., TMS, Warrendale, PA, 1990, pp. 3–16.
37. C.M. Sellars and J.A. Whiteman: Met. Sci., 1979, vol. 13, pp. 187–94.10.1016/0036-9748(79)90290-4 ↗
38. D.J. Towle and T. Gladman: Met. Sci., 1979, vol. 13, pp. 246–56.
39. I. Kozasu and T. Shimizu: Trans. Iron & Steel Inst., Jpn. 1971, vol. 11, pp. 359–66.10.2355/isijinternational1966.11.359 ↗
40. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, Elsevier Science Ltd., New York, NY, 1996.
41. F. Ahlblom: “A Metallographic Study of Recrystallization After Hot Working in an 18/8 Austenitic Stainless Steel,” Report No. IM-1210, Swedish Institute for Metal Research, Apr. 1977, pp. 1–27.
42. R.E. Schramm and R.P. Reed: Metall. Trans. A, 1975, vol. 6A, pp. 1345–50.10.1007/BF02641927 ↗
43. A.W. Thompson and J.A. Brooks: Metall. Trans. A, 1975, vol. 6A, pp. 1431–42.10.1007/BF02641935 ↗
44. C.J. Novak: in Handbook of Stainless Steels, D. Peckner and I.M. Bernstein, eds., McGraw-Hill Book Company, New York, NY, 1977, pp. 4-1–4-78.
45. R.E. Stoltz and J.B. Vander Sande: Metall. Trans. A, 1980, vol. 11A, pp. 1033–37.10.1007/BF02654717 ↗
46. M.J. Stewart: Metall. Trans. A, 1975, vol. 6A, pp. 1672–74.10.1007/BF02641988 ↗
47. G.Y. Chin: The Inhomogeneity of Plastic Deformation, ASM, Metals Park, OH, 1973, pp. 83–112.
48. U.F. Kocks: J. Eng. Mater. Technol., 1976, vol. 98, pp. 76–85.10.1115/1.3443340 ↗
49. H. Mecking and U.F. Kocks: Acta Metall., 1981, vol. 29, pp. 1865–75.10.1016/0001-6160(81)90112-7 ↗
50. Y. Estrin and H. Mecking: Acta Metall., 1984, vol. 32, pp. 57–70.10.1016/0001-6160(84)90202-5 ↗
51. M. Miller and P. Dawson: J. Mech. Phys. Solids, 1997, vol. 45 (11–12), pp. 1781–804.10.1016/S0022-5096(97)00029-X ↗
52. M. Goerdeler and G. Gottstein: in Recrystallization and Grain Growth, G. Gottstein and D.A. Molodov, eds., Springer-Verlag, New York, NY, 2001, pp. 987–94.