Rapid Transformation Annealing: a Novel Method for Grain Refinement of Cold-Rolled Low-Carbon Steels
Source abstract
Abstract
A novel heat treatment, rapid transformation annealing (RTA) is introduced, which uses the refining effect of the phase transformation during recrystallization annealing. The RTA is comprised of rapid heating including the full or partial phase transformation of cold-rolled, nonrecrystallized, or partly recrystallized α microstructure to γ microstructure combined with subsequent rapid cooling to ambient temperature. In this way, a substantial grain refinement compared to conventional industrial annealing of cold-rolled strip can be realized. Minimum homogeneous grain sizes of 2.3 μm are produced in microalloyed high-strength low-alloy (HSLA) steels. A plain low-carbon steel shows despite any microalloying grain sizes of about 2.5 μm. Grain refinement results in a substantial increase in strength and in a pronounced strain hardening in the ΘIV stage. Simultaneously, the uniform and total elongation slightly decrease, which is a physical consequence of Considere’s instability criterion. By a refinement from 4.2 to 2.3 μm, the yield and tensile strength of a HSLA grade can be increased by about 130 MPa to 535 and 650 MPa, while the total elongation is reduced by about four percentage points to 21 pct, i.e., a still moderate formability is provided. In general, the ductility-strength relationship remains similar to the conventional behavior. For all investigated steel grades, the Hall–Petch (HP) relationship is fulfilled. Furthermore, it is proved that RTA cycles can be realized in pilot scale as far as induction heating devices are applied.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. R.K. Gibbs, P.D. Hodgson, B.A. Parker, , P.K. Liaw, J.R. Weertmann, H.L. Marcus, J.S. Santner (Eds.), Morris E. Fine Symp. TMS, Warrendale, PA, 1991, 73–81
2. C. Ouchi: Int. Forum on Creation of Supermetallic Material Consisting of Amorphous, Nano-Scale and Mesoscopic Structures (FCSMM), Tokyo, 1997, 31–38
3. R.C. Hudd, L.K. Lyons, A. De Paepe, C. Stolz, and J. Collins: “The Ultra Rapid Heat Treatment of Low Carbon Strip,” ECSC Final Report, EUR 18562 EN, Luxembourg, 1998
4. A.A. Howe, S.J. Newnham, L. Vandenberghe, M. Barteri, M. Mecozzi, and C. Herzig: “Ultra-Fine Steel Flat Products,” ECSC Final Report, EUR 20225 EN, Luxembourg, 2002
5. I. Salvatori, C. Mesplont, D. Crowther, D. Ponge, and R. Song: “Ultra-Fine Grained Steel by Innovative Deformation Cycles,” ECSC Final Report, Luxembourg, 2006
6. R. Priestner, L. Ali: Mater. Sci. Technol., 1993, 9:135–4110.1179/mst.1993.9.2.135 ↗
7. T. Ishikawa, H. Yoshikawa, T. Inoue, Y. Nomiyama, and S. Imai: Nippon Steel Technical Report No. 75, Nov. 1997, pp. 31–42
8. H. Mabuchi, T. Ishikawa, Y. Nomiyama: R. Asafahani, (ed)., Int. Symp. on Accelerated Cooling/Direct Quenching Steels. ASM, Indianapolis, IN, 1997, pp. 43–50
9. D.H. Shin, W.-J. Kim, W.Y. Choo: Scripta Mater, 1999, 41:259–6210.1016/S1359-6462(99)00156-6 ↗
10. S. Saito, N. Tsuji, H. Utsunomiya, T. Sakai, R.G. Hong: Scripta Mater., 1998, 39:1221–2710.1016/S1359-6462(98)00302-9 ↗
11. A. Belyakov, Y. Sakai, T. Hara, Y. Kimura, K. Tsuzaki: Metall. Mater. Trans. A, 2001, 32A:1769–7610.1007/s11661-001-0153-3 ↗
12. B.Q. Han, S. Yue: J. Mater. Proc. Technol., 2003, 136:100–0410.1016/S0924-0136(02)01014-2 ↗
13. C. Lesch, W. Bleck, P. Álvarez, J. Gil Sevillano, H. Petitgand, J.C. Sartini, C. Le Corre, and J. Schöttler: “Grain Refinement of Cold Rolled Microalloyed Steels by Rapid Transformation Annealing,” ECSC Final Report, EUR 22008 EN, Luxembourg, 2006
14. W. Bleck, F. Brühl, C. Lesch: MPT Int., 2001, 24:70–76
15. P. Álvarez, C. Lesch, W. Bleck, H. Petitgand, J. Schöttler, and J. Gil Sevillano: Int. Conf. on Microalloying for New Steel Process and Applications, J.M. Rodriguez-Ibabe, I. Gutiérrez, B. López, and A. Iza-Mendia, eds., Materials Science Forum, vols. 500–501, Trans Tech Publications Ltd., Zürich, 2005, pp. 771–7810.4028/0-87849-981-4.771 ↗
16. M. Militzer, R. Pandi, E.B. Hawbolt: Metall. Mater. Trans. A, 1996, 27A:1547–5610.1007/BF02649814 ↗
17. M. Thompson, M. Ferry, P.A. Manohar: Iron Steel Inst. Jpn. Int., 2001, 41:891–9910.2355/isijinternational.41.891 ↗
18. N. Yoshinaga, K. Ushioda, A. Itami, O. Akisue: Iron Steel Inst. Jpn., 1994, 34:33–4210.2355/isijinternational.34.33 ↗
19. T. Yokota, C. García, Mateo, H.K.D.H. Bhadeshia: Scripta Mater., 2004, 51:767–7010.1016/j.scriptamat.2004.06.006 ↗
20. L. Zhang, C.B. Zhang, Y.M. Wang, X.H. Liu, G.D. Wang: J. Mater. Res., 2002, 17:2251–5910.1557/JMR.2002.0331 ↗
21. B. Mintz: Met. Technol., 1984, 11:52–6010.1179/030716984803274765 ↗
22. C. Lesch: Ph.D. Thesis, RWTH Aachen University, Aachen, Germany, 2006
23. B. Mintz: Met. Technol., 1984, 11:265–7210.1179/030716984803274693 ↗
24. R. Priestner, P.D. Hodgson: Mater. Sci. Technol., 1992, 8:849–5410.1179/mst.1992.8.10.849 ↗
25. N. Tsuji, Y. Ito, Y. Saito, Y. Minamino: Scripta Mater., 2002, 47:893–9910.1016/S1359-6462(02)00282-8 ↗
26. X.F. Fang, W. Dahl: Mater. Sci. Eng. A, 1995, A203:14–2510.1016/0921-5093(95)09841-0 ↗
27. X. Fang, W. Dahl: Z. Metallkd., 1995, 86:41–48