journal article·2012-07

Friction Stir Welding in HSLA-65 Steel: Part I. Influence of Weld Speed and Tool Material on Microstructural Development

S. J. Barnes, A. R. Bhatti, A. Steuwer, R. Johnson, J. Altenkirch, P. J. Withers

Publisher page

Abstract

A systematic set of single-pass full penetration friction stir bead-on-plate and butt-welds in HSLA-65 steel were produced using a range of different traverse speeds (50 to 500 mm/min) and two tool materials (W-Re and PCBN). Microstructural analysis of the welds was carried out using optical microscopy, and hardness variations were also mapped across the weld-plate cross sections. The maximum and minimum hardnesses were found to be dependent upon both welding traverse speed and tool material. A maximum hardness of 323 Hv(10) was observed in the mixed martensite/bainite/ferrite microstructure of the weld nugget for a welding traverse speed of 200 mm/min using a PCBN tool. A minimum hardness of 179 Hv(10) was found in the outer heat-affected zone (OHAZ) for welding traverse speed of 50 mm/min using a PCBN tool. The distance from the weld centerline to the OHAZ increased with decreasing weld speed due to the greater heat input into the weld. Likewise for similar energy inputs, the size of the transformed zone and the OHAZ increased on moving from a W-Re tool to a PCBN tool probably due to the poorer thermal conductivity of the PCBN tool. The associated residual stresses are reported in Part II of this series of articles. © The Minerals, Metals & Materials Society and ASM International 2012.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Temple-Smith, and C.J. Dawes: International Patent No. PCT/GB92/02203.
2. A.P. Reynolds: Sci. Technol. Weld., 2000, vol. 5 (2), pp. 120–24.10.1179/136217100101538119 ↗
3. A.P. Reynolds, W.D. Lockwood, and T.U. Seidel: Mater. Sci. Forum, 2000, vols. 331–339, pp. 1719–24.10.4028/www.scientific.net/MSF.331-337.1719 ↗
4. P.L. Threadgill, A.J. Leonard, H.R. Shercliff, and P.J. Withers: Int. Mater. Rev., 2009, vol. 54 (2), pp. 50–93.10.1179/174328009X411136 ↗
5. M.J. Peel, A. Steuwer, P.J. Withers, T. Dickerson, Q. Shi, and H. Shercliff: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2183–93.10.1007/BF02586138 ↗
6. D.G. Kinchen, Z. Li, and G.P. Adams: Proc. 1st Int. Conf. on Friction Stir Welding, TWI, Cambridge, United Kingdom, 1999, Session 9, paper no. 2.
7. B.K. Christner and G.D. Sylva: Proc. ICAWT, EWI, Columbus, OH, 1996, pp. 311–20.
8. L.E. Murr, G. Liu, and J.C. McClure: J. Mater. Sci., 1997, vol. 16, pp. 1801–03.
9. A.P. Reynolds: Proc. 5th Int. Conf. on Trends in Welding Research, ASM INTERNATIONAL, Materials Park, OH, 1998, pp. 563–67.
10. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, W.H. Bingel, and R.H. Spurling: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955–64.10.1007/s11661-998-0021-5 ↗
11. M. Peel, A. Steuwer, M. Preuss, and P.J. Withers: Acta Mater., 2003, vol. 51, pp. 4791–4801.10.1016/S1359-6454(03)00319-7 ↗
12. A. Steuwer, M.J. Peel, and P.J. Withers: Mater. Sci. Eng. A, 2006, vol. 441, pp. 187–96.10.1016/j.msea.2006.08.012 ↗
13. R. Johnson, J. Dos Santos, and M. Magnasco: Proc. 4th Int. Friction Stir Welding Symp., Park City, UT, 2003.
14. T.J. Lienert, W.L. Stellwag, B.B. Grimmett, and R.W. Warke: Weld. Res. Suppl. Weld. J., 2003, vol. 82, pp. 1s–9s.
15. P. Konkol: Proc. 4th Int. Friction Stir Welding Symp., Park City, UT, 2003.
16. K. Okamoto, S. Hirano, M. Inagaki, S.H.C. Park, Y.S. Sato, H. Kokawa, T. Nelson, and C.D. Sorensson: Proc. 4th Int. Friction Stir Welding Symp., Park City, UT, 2003.
17. M. Posada, J. DeLoach, A.P. Reynolds, R. Fonda, and J. Halpin: 4th Int. Friction Stir Welding Symp., Park City, UT, 2003.
18. A.P. Reynolds, W. Tang, M. Posada, and J. DeLoach: Sci. Technol. Weld. J., 2003, vol. 8 (6), pp. 455–60.10.1179/136217103225009125 ↗
19. A. Ozekcin, H.W. Jin, J.Y. Koo, N.V. Bangaru, R. Ayer, G. Vaughn, R.J. Steel, and S.M. Packer: Int. J. Offshore Polar Eng., 2004, vol. 14 (4), pp. 284–88.
20. Z. Feng, M.L. Santella, S.A. David, R.J. Steel, S.M. Packer, T. Pan, M. Kuo, and R.S. Bhatnagar: SAE Int., 2005, paper no. 2005-01-1248.
21. L. Cui, H. Fujii, N. Tsuji, and K. Nogi: Scripta Mater., 2007, vol. 56 pp. 637–40.10.1016/j.scriptamat.2006.12.004 ↗
22. A.P. Reynolds, W. Tang, T.G. Herold, and H. Prask: Scripta Mater., 2003, vol. 48, pp. 1289–94.10.1016/S1359-6462(03)00024-1 ↗
23. Y.S. Sato, H. Yamanoi, H. Kokawa, and T. Furuhara: Scripta Mater., 2007, vol. 57, pp. 557–60.10.1016/j.scriptamat.2007.04.050 ↗
24. S.J. Barnes, A. Steuwer, S. Mahawish, R. Johnson, and P.J. Withers: Mater. Sci. Eng. A, 2008, vol. 492, pp. 35–44.10.1016/j.msea.2008.02.049 ↗
25. X.K. Zhu and Y.J. Chao: J. Mater. Process. Technol., 2004, vol. 146, pp. 263–72.10.1016/j.jmatprotec.2003.10.025 ↗
26. H. Fujii, L. Cui, N. Tsuji, M. Maeda, K. Nakata, and K. Nogi: Mater. Sci. Eng. A, 2006, vol. 429, pp. 50–57.10.1016/j.msea.2006.04.118 ↗
27. T. Saeid, A. Abdollah-zadeh, H. Assadi, and F. Malek Ghaini: Mater. Sci. Eng. A, 2008, vol. 496, pp. 262–68.10.1016/j.msea.2008.05.025 ↗
28. P.L. Threadgill and R. Johnson: Proc. 14th Int. Offshore and Polar Engineering Conf., Toulon, France, 2004, pp. 1–7.
29. R. Nandan, T. DebRoy, and H.K.D.H. Bhadeshia: Prog. Mater. Sci., 2008, vol. 53, pp. 980–1023.10.1016/j.pmatsci.2008.05.001 ↗
30. M.F. Sinfield, J.C. Lippold, and B.T. Alexandrov: Proc. 7th Int. Friction Stir Welding Symp., Awaji Island, Japan, 2008.
31. S.M. Packer, T. Nelson, C.D. Sorensson, R.J. Steel, and M. Matsunaga: Proc. 4th Int. Friction Stir Welding Symp., Park City, UT, 2003.
32. C.D. Sorensen, T.W. Nelson, and S.M. Packer: Proc. 3rd Int. Friction Stir Welding Symp., Kobe, Japan, Sept. 2001.
33. R.J. Steel, Q. Liu, X. Yao, S. Packer, and T. Leonhardt: Proc. 7th Int. Friction Stir Welding Symp. 2008, Awaji Island, Japan, 2008.
34. T. Weinberger, S. Khosa, B. Führer, and N. Enzinger: Proc. 7th Int. Friction Stir Welding Symp. 2008, Awaji Island, Japan, 2008.
35. W.M. Thomas: TWI Connect, Sept/Oct 1998, No. 96.
36. C.D. Sorensen and T.W. Nelson: Proc. 4th Int. Friction Stir Welding Symp., 2003, Park City, UT, 2003.
37. W.M. Thomas, P.L. Threadgill, and E.D. Nicholas: Sci. Technol. Weld. Join., 1999, vol. 4 (6), pp. 365–72.10.1179/136217199101538012 ↗
38. A. Steuwer, S.J. Barnes, J. Altenkirch, R. Johnson, and P.J. Withers: Metall. Mater. Trans. A, DOI:10.1007/s11661-011-0643-x.10.1007/s11661-011-0643-x ↗
39. P.L. Threadgill: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 357–60.10.1179/174329307X197629 ↗
40. B.T. Alexandrov, J.C. Lippold, J. Tatman, and G. Murray: Proc. Sheet Welding Conf. XIII, Livonia, MI, 2008.
41. R.A. Farrar, Z. Zhang, S.R. Bannister, and G.S. Barritte: J. Mater. Sci., 1993, vol. 28, pp. 1385–90.10.1007/BF01191982 ↗