Laser Keyhole Welding of Dissimilar Ti-6Al-4V Titanium Alloy to AZ31B Magnesium Alloy
Source abstract
Abstract
Laser keyhole welding of Ti-6Al-4V titanium alloy to AZ31B magnesium alloy was developed, and the correlations of process parameters, joint properties, and bonding mechanism were studied. The results show that the offset from the laser beam center on AZ31B side to the edge of the weld seam plays a big role in the joint properties by changing the power density irradiated at the Ti–Mg initial interface. The optimal range of the offset is 0.3 to 0.4mm in the present study. Some lamellar and granular Ti-rich mixtures are observed in the fusion zone, which is formed by intermixing melted Ti-6Al-4V with liquid AZ31B. The maximum ultimate tensile strength of the joints reaches 266 MPa. Furthermore, the fracture surface consists of scraggly remaining weld metal and smooth Ti surface. The higher the failure strength, the smaller the proportion of smooth Ti surface to whole interface is. Finally, the bonding mechanism of the interfacial layer is summarized by the morphologies and test results of fracture surfaces.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. C. Leyens and M. Peters: Titanium and Titanium Alloys, Wiley-VCH, Weinheim, Germany, 2003, pp. 333-496.10.1002/3527602119 ↗
2. G. Casalino, F. Curcio, and F.M.C. Minutolo: J. Mater. Process. Tech., 2005, vol. 167, nos. 2, 3, pp. 422–28.10.1016/j.jmatprotec.2005.05.031 ↗
3. X. Cao and M. Jahazi: Optic. Laser. Eng., 2009, vol. 47, pp. 1231-41.10.1016/j.optlaseng.2009.05.010 ↗
4. X. Cao, M. Jahazi, J.P. Immarigeon, and W. Wallace: J. Mater. Process. Tech., 2006, vol. 171, pp. 188-204.10.1016/j.jmatprotec.2005.06.068 ↗
5. H.E. Friedrich and B.L. Mordike: Magnesium Technology, Springer, Berlin, Germany, 2006, pp. 204-14.
6. C.M. Liu, X.R. Zhu, and H.T. Zhou: Phase Diagrams of Magnesium Alloys, Central South University Press, Changsha, China, p. 56.
7. L.M. Liu and X. Zhao: Mater. Charact., 2008, vol. 59, pp. 1279-84.10.1016/j.matchar.2007.10.012 ↗
8. X.D. Qi and G. Song: Mater. Des., 2010, vol. 31, pp. 605-09.10.1016/j.matdes.2009.06.043 ↗
9. Y.G. Miao, D.F. Han, J.Z. Yao, and F. Li: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 97-103.10.1179/136217109X12518083193676 ↗
10. Y.G. Miao, D.F. Han, J.Z. Yao, and F. Li: Mater. Des., 2010, vol. 31, pp. 3121-26.10.1016/j.matdes.2009.12.035 ↗
11. S Jana, Y. Hovanski, and G.J. Grant: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 3173-82.10.1007/s11661-010-0399-8 ↗
12. Y.C. Chen and K. Nakata: Mater. Des., 2009, vol. 30, pp. 3913-19.10.1016/j.matdes.2009.03.007 ↗
13. T. Liyanage, J. Kilbourne, and A.P. Gerlich: Sci. Technol. Weld. Join., 2009, vol. 14, pp. 500-08.10.1179/136217109X456960 ↗
14. T. Watanabe, K. Kagiya, A. Yanagisawa, and H. Tanabe: Quart J. Jpn. Weld. Soc., 2006, vol. 24, pp.108-15.10.2207/qjjws.24.108 ↗
15. A.A. Nayeb-Hashemi, J.B. Clark, and L.J. Swartzendruber: Binary Alloy Phase Diagrams, ASM International, Materials Park, OH, 1990, p. 1722.
16. S. Fukumoto, T. Inoue, S. Mizuno, and K. Okita: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 124-30.10.1179/136217109X12577814486692 ↗
17. S.H. Chen, L.Q. Li, Y.B. Chen, and D.J. Liu: Trans. Nonferrous. Met. Soc. China, 2010, vol. 20, pp. 64-70.10.1016/S1003-6326(09)60098-4 ↗
18. G. Sierra, P. Peyre, F.D. Beaume, and D. Stuart: Sci. Technol. Weld. Join., 2008, vol. 13, pp. 430-37.10.1179/174329308X341852 ↗
19. S.H. Chen, L.Q Li, Y.B. Chen, and J.H. Huang: J. Alloys Compd., 2010, vol. 509, pp. 891-98.10.1016/j.jallcom.2010.09.125 ↗
20. T. DebRoy and H.K.D.H. Bhadeshia: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 266-68.10.1179/174329310X12726496072400 ↗
21. Y.C. Chen and K. Nakata: Scripta. Mater., 2008, vol. 58, pp. 433-36.10.1016/j.scriptamat.2007.10.033 ↗
22. Y.S. Sato, A. Shiota, and H. Kokawa: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 319-24.10.1179/136217109X12568132624208 ↗
23. L. Quintino, A. Costa, R. Miranda, and D. Yapp: Mater. Des., 2007, vol. 28, pp. 1231-37.10.1016/j.matdes.2006.01.009 ↗
24. Y.J. Quan, Z.H. Chen, X.S. Cong, and Z.H. Yu: Mater. Charact., 2008, vol. 59, pp.1491-97.10.1016/j.matchar.2008.01.010 ↗
25. S.M. Chowdhury, D.L. Chen, S.D. Bhole, E. Powidajko, D.C. Wechma, and Y. Zhou: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 1974-89.10.1007/s11661-010-0574-y ↗
26. Y.J. Quan, Z.H. Chen, X.S. Gong, and Z.H. Yu: Mater. Sci. Eng. A, 2008, vol. 496, pp. 45-51.10.1016/j.msea.2008.04.065 ↗
27. F. Czerwinski: Acta. Mater., 2002, vol. 50, pp. 2639-54.10.1016/S1359-6454(02)00094-0 ↗
28. M. Gao, Y. Cao, X.Y. Zeng, and T.X. Lin: Sci. Technol. Weld. Join., 2010, vol. 14, pp. 274-81.10.1179/136217109X406929 ↗
29. L.N. Kishore, T.F. Jay, and G. Mark: J. Phys. D: Appl. Phys., 1996, vol. 29, 1831-41.10.1088/0022-3727/29/7/018 ↗
30. S. Kou: Welding Metallurgy, Wiley, Hoboken, NJ, 2003, pp. 45-46.
31. H.W. Choi, D.F. Farson, and M.H. Cho: Weld. J., 2006, vol. 85, pp. 174s-9s.
32. M.H. Cho and D.F. Farson: Weld. J., 2007, vol. 86, pp. 253s-62s.
33. W. Song, K. Saida, and A. Ando: J. Jpn Weld. Soc., 2004, vol. 22, pp. 108-15.