journal article·2001-05

Tensile ductility of several commercial aluminum alloys at elevated temperatures

Eric M. Taleff, Peter J. Nevland, Paul E. Krajewski

Publisher page

Abstract

One experimental and five commercial aluminum alloys were tested in tension at elevated temperatures (225 °C to 500 °C) over a range of strain rates (2×10−5 to 10−1 s−1). The experimental alloy contained 5 wt pct Zn with a balance of Al. The commercial alloys included AA 5182, 5754, 7150, 6111, and 6022. Two 5182 materials were examined, one produced by standard ingot-processing methods and the other by continuous casting. The 5754 and 5182 alloys exhibited a deformation regime consistent with solute-drag creep for values of diffusivity-compensated strain rate less than 1013 m−2. Within this regime, the 5754 and ingot-metallurgy 5182 materials exhibited tensile ductilities up to 140 pct. The continuously cast 5182 material exhibited lower ductility in this regime than the 5754 and ingot-metallurgy 5182 materials, despite similar stress exponents. Ductility was reduced in the continuously cast 5182 because of significant dynamic grain growth and cavitation. The 7150, Al-5Zn, 6111, and 6022 materials exhibited significantly higher stress exponents and lower tensile ductilities than the 5000-series materials.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. E.M. Taleff, G.A. Henshall, T.G. Nieh, D.R. Lesuer, and J. Wadsworth: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1081–91.
2. E.M. Taleff, P.J. Nevland, and S.J. Yoon: in Deformation, Processing, and Properties of Structural Materials, E.M. Taleff, C.K. Syn, and D.R. Lesuer, eds., TMS, Warrendale, PA, 2000, pp. 373–84.
3. E.M. Taleff and P.J. Nevland: JOM, 1999, vol. 51, pp. 34–36.10.1007/s11837-999-0009-7 ↗
4. P.A. Friedman and A.K. Ghosh: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3827–39.10.1007/BF02595632 ↗
5. O.D. Sherby and J. Wadsworth: Progr. Mater. Sci., 1989, vol. 33, pp. 169–221.10.1016/0079-6425(89)90004-2 ↗
6. C.A. Lavender, J.S. Vetrano, M.T. Smith, S.M. Bruemmer, and C.H. Hamilton: Mater. Sci. Forum, 1994, vols. 170–172, pp. 279–86.10.4028/www.scientific.net/MSF.170-172.279 ↗
7. J.S. Vetrano, C.A. Lavender, C.H. Hamilton, M.T. Smith and S.M. Bruemmer: Scripta Metall. Mater., 1994, vol. 30, pp. 565–70.10.1016/0956-716X(94)90430-8 ↗
8. R. Verma, A.K. Ghosh, S. Kim, and C. Kim: Mater. Sci. Eng., 1995, vol. A191, pp. 143–50.10.1016/0921-5093(94)09644-9 ↗
9. R. Verma, P.A. Friedman, A.K. Ghosh, S. Kim, and C. Kim: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1889–98.10.1007/BF02651938 ↗
10. M.A. Khaleel, M.T. Smith, and S.G. Pitman: Scripta Mater., 1997, vol. 37, pp. 1909–15.10.1016/S1359-6462(97)00381-3 ↗
11. K. Kannan, C.H. Johnson, and C.H. Hamilton: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1211–20.10.1007/s11661-998-0248-1 ↗
12. E.M. Taleff, D.R. Lesuer, and J. Wadsworth: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 343–52.10.1007/BF02648411 ↗
13. E.M. Taleff, P.J. Nevland, and P.E. Krajewski: in Creep Behavior of Advanced Materials for the 21st Century, R.S. Mishra, A.K. Mukherjee, and K.L. Murty, eds., TMS, Warrendale, PA, 1999, No. 3A, pp. 349–58.
14. S. Mrowec: Defects and Diffusion in Solids, An Introduction, Elsevier/North-Holland, Inc., New York, NY, 1980, p. 397.
15. Y. Funamizu and K. Watanabe: Trans. JIM, 1972, vol. 13, pp. 278–83.10.2320/matertrans1960.13.278 ↗
16. J. Weertman: J. Appl. Phys., 1957, vol. 28, pp. 1185–89.10.1063/1.1722604 ↗
17. J. Weertman: Trans. TMS-AIME, 1960, vol. 218, pp. 207–18.
18. E.W. Hart: Acta Metall., 1967, vol. 15, pp. 351–55.10.1016/0001-6160(67)90211-8 ↗
19. M.A. Burke and W.D. Nix: Acta Metall., 1975, vol. 23, pp. 793–98.10.1016/0001-6160(75)90195-9 ↗
20. J.W. Hutchinson and H. Obrecht: Fracture, 1977, vol. 1, pp. 101–16.
21. A.K. Ghosh: Acta Metall., 1977, vol. 25, pp. 1413–24.10.1016/0001-6160(77)90072-4 ↗
22. O.D. Sherby, R.A. Anderson, and J.E. Dorn: Trans. AIME, 1951, vol. 191, p. 643.
23. ASM Specialty Handbook: Aluminum and Aluminum Alloys, J.R. Davis, eds., ASM International, Materials Park, OH, 1996, pp. 19–24.
24. E.E. Underwood: Metals Handbook: Metallography Structures and Phase Diagrams, 8th ed., ASM, Metals Park, OH, 1973, vol. 8, pp. 37–47.
25. W. Köster: Z. Metallk., 1948, vol. 39, pp. 9–12.
26. H.J. Frost and M.F. Ashby: Deformation-Mechanism Maps, Pergamon Press, New York, NY, 1982, p. 21.
27. O.D. Sherby and P.M. Burke: Progr. Mater. Sci., 1968, vol. 13, pp. 325–90.10.1016/0079-6425(68)90024-8 ↗
28. H. Oikawa, N. Matsuno, and S. Karashima: Met. Sci., 1975, vol. 9, pp. 209–12.10.1016/0036-9748(75)90562-1 ↗
29. R. Horiuchi and M. Otsuka: Trans. JIM, 1972, vol. 13, pp. 284–93.10.2320/matertrans1960.13.284 ↗
30. P. Yavari and T.G. Langdon: Acta Metall., 1982, vol. 30, pp. 2181–96.10.1016/0001-6160(82)90139-0 ↗
31. T.R. McNelley, D.J. Michel, and A. Salama: Scripta Metall., 1989, vol. 23, pp. 1657–62.10.1016/0036-9748(89)90338-4 ↗
32. I.S. Servi and N.J. Grant: Trans. AIME, 1951, vol. 191, pp. 917–22.
33. M.E. Kassner and M.-T. Pérez-Prado: Progr. Mater. Sci., 2000, vol. 45, pp. 1–102.10.1016/S0079-6425(99)00006-7 ↗
34. M.S. Mostafa and F.A. Mohamed: Metall. Trans. A, 1986, vol. 17A, pp. 365–66.10.1007/BF02643918 ↗
35. H.W. King: J. Mater. Sci., 1966, vol. 1, pp. 79–90.10.1007/BF00549722 ↗
36. O.D. Sherby, R.H. Klundt, and A.K. Miller: Metall. Trans. A, 1977, vol. 8A, pp. 843–50.10.1007/BF02661565 ↗
37. J. Lin and O.D. Sherby: Res. Mechanica, 1981, vol. 2, pp. 251–93.
38. Binary Alloy Phase Diagrams, T.B. Massalski, ed., 2nd ed. ASM International, Materials Park, OH, 1990, vol. 1, pp. 211–13.
39. J.L. Murray and A.J. McAlister: Bull. Alloy Phase Diagrams, 1984, vol. 5, pp. 74–83.10.1007/BF02868729 ↗
40. R.A. Ayres: Metall. Trans. A, 1979, vol. 10A, pp. 849–54.10.1007/BF02658303 ↗
41. A.A. Tavassoli, S.E. Razavi, and N.M. Fallah: Metall. Trans. A, 1975, vol. 6A, pp. 591–94.10.1007/BF02658423 ↗
42. E.M. Taleff, T. Leon-Salamanca, R.A. Ketcham, R. Reyes, and W.D. Carlson: J. Mater. Res., 2000, vol. 15, pp. 76–84.10.1557/JMR.2000.0015 ↗
43. R.A. Ayres and M.L. Wenner: Metall. Trans. A, 1979, vol. 10A, pp. 41–46.10.1007/BF02686404 ↗