journal article·2006-08

The constitutive behavior of laser welds in 304L stainless steel determined by digital image correlation

B. L. Boyce, P. L. Reu, C. V. Robino

Publisher page

Abstract

A digital image correlation (DIC) method has been used to characterize the constitutive tensile stress-strain response in 304L austenitic stainless steel weldments produced by both continuous-wave (CW) and pulsed-wave (PW) laser welding. The method provides quantitative two-dimensional (2-D) strain maps of the deformation field across the transverse weld samples throughout the tensile test. Local stress-strain response was extracted from regions within the fusion zone and compared to base metal response. The weldments were found to have a higher yield strength than the base metal. The metallurgical origin for the fusion zone strengthening was largely attributed to Hall-Petch and ferrite content effects. While failures localized in the fusion zone with little appreciable necking, the material within the fusion zone retained considerable local ductility: more than 45 pct strain at failure. Significant weld root porosity found in the PW condition and absent in the CW condition appeared to have no deleterious effect on the mechanical performance under the present test conditions in this very ductile, flaw-tolerant alloy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. Y. Cui and C.D. Lundin:J. Mater. Sci., 2005, vol. 40, pp. 1281–83.10.1007/s10853-005-6952-y ↗
2. J.R. Foulds, J. Moteff, V.K. Sikka, and J.W. McEnerney:Metall. Trans. A, 1983, vol. 14A, pp. 1357–66.10.1007/BF02664819 ↗
3. J.A. Brooks, S.H. Goods, and C.V. Robino: Report No. SAND2000-8002, Sandia National Laboratories, Albuquerque, NM, Aug. 2000.
4. W. Tong, H. Tao, X. Jiang, N. Zhang, M.P. Marya, L.G. Hector, Jr., and X.Q. Gayden:Metall. Mater. Trans. A, 2005, vol. 36A, pp. 2651–69.10.1007/s11661-005-0263-4 ↗
5. S.M. Zuniga and S.D. Sheppard:Model. Simul. Mater. Sci., 1995, vol. 3, pp. 391–416.10.1088/0965-0393/3/3/007 ↗
6. J.F. Zarzour, P.J. Konkol, and H. Dong:Mater. Characterization, 1996, vol. 37, pp. 195–209.10.1016/S1044-5803(96)00128-3 ↗
7. E. Markiewicz, P. Ducrocq, P. Drazetic, G. Haugou, T. Fourmentraux, and J.Y. Berard:Int. J. Mater. Prod. Technol., 2001, vol. 16, pp. 484–509.10.1504/IJMPT.2001.001277 ↗
8. Aerospace Structural Metals Handbook, 37th ed., CINDAS/USAFCRDA Handbooks Operation, West Lafayette, IN, 2001.
9. Alloy Steel and Stainless Steel Bolting Materials for Low-Temperature Service, ASTM A320-05a, ASTM International, West Conshohocken, PA, 2005.
10. D. Hauser and J.A. Van Echo:Welding J., 1978, vol. 57, pp. 81s-144s.
11. M.J. McGinnis, S. Pessiki, and H. Turker:Exp. Mech., 2005, vol. 45, pp. 359–67.10.1007/BF02428166 ↗
12. J. Kang, D.S. Wilkinson, M. Jain, J.D. Embury, A.J. Beaudoin, S. Kim, R. Mishira, and A.K. Sachdev:Acta Mater., 2006, vol. 54, pp. 209–18.10.1016/j.actamat.2005.08.045 ↗
13. S.W. Cho, J.F. Cardenas-Garcia, and I. Chasiotis:Sens. Actuat. A-Phys., 2005, vol. 120, pp. 163–71.10.1016/j.sna.2004.11.028 ↗
14. A.P. Reynolds and F. Duvall:Welding J., 1999, vol. 78, pp. 355s-60s.
15. W.D. Lockwood, B. Tomaz, and A.P. Reynolds:Mater. Sci. Eng. A-Struct., 2002, vol. A323, pp. 348–53.10.1016/S0921-5093(01)01385-5 ↗
16. W.D. Lockwood and A.P. Reynolds:Mater. Sci. Eng. A-Struct., 2003, vol. A339, pp. 35–42.10.1016/S0921-5093(02)00116-8 ↗
17. C. Genevois, A. Deschamps, A. Denquin, and B. Doisneau-Cottignies:Acta Mater., 2005, vol. 53, pp. 2447–58.10.1016/j.actamat.2005.02.007 ↗
18. C. Genevois, A. Deschamps, and P. Vacher:Mater. Sci. Eng. A-Struct., 2006, vol. 415, pp. 162–70.10.1016/j.msea.2005.09.032 ↗
19. P. Cheng, M.A. Sutton, H.W. Schreier, and S.R. McNeill:Exp. Mech., 2002, vol. 42, pp. 344–52.10.1007/BF02410992 ↗
20. M.B. Prime:J. Eng. Mater.-Trans. ASME, 2001, vol. 123, pp. 162–68.10.1115/1.1345526 ↗
21. A.A. Chandra, A.T. DeWald, and M.R. Hill: University of California, Davis, CA, unpublished research, 2004.
22. J.A. Brooks and J.C. Lippold:ASM Handbook, 9th Edition, Volume 6, Welding Brazing and Soldering, ASM International, Materials Park, OH, 1993, pp. 456–70.10.31399/asm.hb.v06.a0001410 ↗
23. K.K. Singh, S. Sangal, and G.S. Murty:Mater. Sci. Technol., 2002, vol. 18, pp. 165–72.10.1179/026708301125000384 ↗
24. K.J. Irvine, T. Gladman, and F.B. Pickering:J. Iron Steel Inst., 1969, vol. 207, pp. 1017–28.
25. J.C. Lippold and D.J. Kotecki:Welding Metallurgy and Weldability of Stainless Steels, John Wiley, Hoboken, NJ, 2005, pp. 168–73.
26. G.R. Eisler and P.W. Fuerschbach:Proc. 7th Int. Conf. on Computer Technology in Welding; San Francisco, CA, 1997, pp. 257–68.
27. Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications, ASTM Specification A 240-06, ASTM International, West Conshohocken, PA, 2006.
28. B.L. Boyce and C.V. Robino: Sandia National Laboratories, Albuquerque, NM, unpublished research, 2005.