Mechanical Property and Microstructure of Linear Friction Welded WASPALOY
Source abstract
Abstract
The mechanical properties and microstructural evolution of WASPALOY joined by linear friction welding (LFW) were investigated in this study. In-situ temperature measurements using thermocouple probes indicated exposure of the weld area to a temperature of at least 1400 K (1126 °C). Based on electron backscatter diffraction (EBSD) mapping of the weldments, up to 50 pct reduction in γ grain size occurred within 0.9 mm of the weld interface as a result of dynamic recrystallization (DRX). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies revealed that progressive dissolution of γ′ precipitates took place from the base metal to the weld interface, where almost no γ′ precipitates were observed. Within 3.3 mm of the weld interface, the γ′ dissolution significantly influenced the hardness profile measured across the extended thermomechanically affected zones (TMAZs). Investigation of strain distributions during tensile testing using the optical Aramis system revealed weak bonding at the edge of the weld due to oxidation. To extrude out oxide layers into the flash, increasing the axial shortening to higher than 1.2 mm is recommended.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · High Temperature Alloys and Creep · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Y.C. Fayman: Mater. Sci. Eng., 1986, vol. 82, pp. 203–15.10.1016/0025-5416(86)90108-4 ↗
2. A.A. Guimaraes: M.Sc. Thesis, McGill University, Montreal, 1980, pp. 1–2.
3. M.E. Nunn: 1st Int. Conf. on Innovation and Integration in Aerospace Sciences, CEIAT, Northern Ireland, United Kingdom, 2005.
4. Z.W. Huang, H.Y. Li, M. Preuss, M. Karadge, P. Bowen, S. Bray, and G. Baxter: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1608–20.10.1007/s11661-007-9194-6 ↗
5. P. Adam: Welding of High Strength Gas Turbine Alloys, Applied Science Publisher Ltd., London, 1978, pp. 737–68.
6. K.R. Vishwakarma, N.L. Richards, and M.C. Chaturvedi: 6th Int. Symp. on Superalloys 718, 625, 706 and Derivatives, E.A. Loria, ed, TMS, Pittsburgh, PA, 2005, pp. 637–47.10.7449/2005/Superalloys_2005_637_647 ↗
7. N.C. Sekhar and R.C. Reed: Sci. Technol. Weld. Join., 2002, vol. 7, pp. 77–87.10.1179/136217102225002628 ↗
8. T.J. Ma, W.-Y. Li, Q.Z. Xue, Y. Zhang, J.L. Li, and S.Q. Yang: Mater. Sci. Forum, 2008, vols. 580–582, pp. 405–08.10.4028/www.scientific.net/MSF.580-582.405 ↗
9. H.Y. Li, Z.W. Huang, S. Bray, G. Baxter, and P. Bowen: Mater. Sci. Technol., 2007, vol. 23, pp. 1408–18.10.1179/174328407X243933 ↗
10. S.W. Kallee, E.D. Nicholas, and M.J. Russell: 10th World Conf. on Titanium, G. Lütjering and J. Albrecht, eds., Wiley VCH, Germany, 2003, pp. 2867–74.
11. K. Asokkumar: WRI J., 2003, vol. 24, pp. 12–20.
12. A. Vairis and M. Frost: Mater. Sci. Eng. A, 2000, vol. 292, pp. 8–17.10.1016/S0921-5093(00)01036-4 ↗
13. H. Seli, I.A. Md. Ismail, E. Rachman, and Z.A. Ahmad: J. Mater. Process. Technol., 2010, vol. 210, pp. 1209–16.10.1016/j.jmatprotec.2010.03.007 ↗
14. I. Hulea, P. Hoffmann, M. Brinza, D.R. Batchelor, and D. Schmeisser: 2nd Int. Symp. on Aluminum Surface Science and Technology, Manchester, England, Emerald Group Publishing Limited, Bingley, United Kingdom, 2000, pp. 157–62.
15. “Resistance and Solid-State Welding,” http://www.ewi.org/capabilities/rssw.asp.
16. A. Vairis and M. Frost: Wear, 1998, vol. 217, pp. 117–31.10.1016/S0043-1648(98)00145-8 ↗
17. “Linear Friction Welding of Blisks for Power Generation,” http://www.twi.co.uk/j32k/unprotected/band_1/power_linearfric.html.
18. O. Roder, D. Helm, S. Neft, J. Albrecht, and G. Luetjering: 6th Int. Conf. on Superalloys 718, 625, 706 and Derivatives, O. Roder, D. Helm, S. Neft, J. Albrecht, and G. Luetjering, eds., TMS, Warrendale, PA, 2005, pp. 649–59.10.7449/2005/Superalloys_2005_649_658 ↗
19. W.A. Baeslack, T.F. Broderick, M. Juhas, and H.L. Fraser: Mater. Charact., 1994, vol. 33, pp. 357–67.10.1016/1044-5803(94)90140-6 ↗
20. M. Karadge, M. Preuss, P.J. Withers, and S. Bray: Mater. Sci. Eng. A, 2008, vol. 491, pp. 446–53.10.1016/j.msea.2008.04.064 ↗
21. P.L. Threadgill: Stainless Steel World, 1996, vol. 88, pp. 65–67.
22. R.E. Bailey: 2nd Int. Conf. on Superalloys—Processing, Seven Springs, PA, Battelle Columbus Labs., Columbus, OH, 1972, pp. J1–J21.
23. C.T. Sims, N.S. Stoloff, and W.C. Hagel: Superalloys II, John Wiley & Sons, New York, NY, 1987, pp. 66–78.
24. M.R. Winstone and J.W. Brooks: Ciência Technol. Mater., 2008, vol. 20, pp. 15–24.
25. M. Preuss, J.W.L. Pang, P.J. Withers, and G.J. Baxter: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3215–25.10.1007/s11661-002-0307-y ↗
26. C. Mary and M. Jahazi: Adv. Mater. Res., 2007, vols. 15–17, pp. 357–62.10.4028/www.scientific.net/AMR.15-17.357 ↗
27. C. Mary and M. Jahazi: Adv. Eng. Mater., 2008, vol. 10, pp. 573–78.10.1002/adem.200700361 ↗
28. N.W. Bonner and A.N. Ezeilo: 6th Int. Conf. on Residual Stresses, G.A. Webster, ed., Oxford, United Kingdom, Institute of Materials, London, 2000, pp. 1385–92.
29. G. Shen, S.L. Semiatin, and R. Shivpuri: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1795–803.10.1007/BF02670767 ↗
30. P. Wanjara and M. Jahazi: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 2149–64.10.1007/s11661-005-0335-5 ↗
31. E. Dalgard, M. Jahazi, and J.J. Jonas: Friction Stir Welding and Processing—V, TMS 2009 Annual Meeting & Exhibition, R.S. Mishra, M.W. Mahoney, and T.J. Lienert, eds., TMS, San Francisco, CA, 2009, pp. 55–64.
32. S. Xu, J.I. Dickson, and A.K. Koul: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2687–95.10.1007/s11661-998-0309-5 ↗
33. B. Lindsley and X. Pierron: Superalloys 2000, T.M. Pollock, R.D. Kissinger, R.R. Bowman, K.A. Green, M. McLean, S. Olson, and J.J. Schirra, eds., TMS, Warrendale, PA, 2000, pp. 59–68.10.7449/2000/Superalloys_2000_59_68 ↗
34. ASTM Standard E 562-02, Annual Book of ASTM Standards, ASTM, Philadelphia, PA, 2002, vol. 3 (1), pp. 1–7.
35. T.J. Ma, W.-Y. Li, and S.Y. Yang: Mater. Des., 2009, vol. 30, pp. 2128–32.10.1016/j.matdes.2008.08.029 ↗
36. W.-Y. Li, T.J. Ma, S.Q. Yang, Q.Z. Xu, Y. Zhang, J.L. Li, and H.L. Liao: Mater. Lett., 2008, vol. 62, pp. 293–96.10.1016/j.matlet.2007.05.037 ↗
37. E.D. Nicholas and W.M. Thomas: Int. J. Mater. Prod. Technol., 1998, vol. 13, pp. 45–55.
38. H.H. Koo and W.A. Baeslack: Mater. Charact., 1992, vol. 28, pp. 157–64.10.1016/1044-5803(92)90039-K ↗
39. M. Preuss, P.J. Withers, and G.J. Baxter: Mater. Sci. Eng. A, 2006, vol. 437, pp. 38–45.10.1016/j.msea.2006.04.058 ↗
40. B. Grant, M. Preuss, P.J. Withers, G. Baxter, and M. Rowlson: Mater. Sci. Eng. A, 2009, vols. 513–514, pp. 366–75.10.1016/j.msea.2009.02.005 ↗
41. A.J. Brand, K. Karhausen, and R. Kopp: Mater. Sci. Technol., 1996, vol. 12, pp. 963–69.10.1179/mst.1996.12.11.963 ↗
42. M. Soucail and Y. Bienvenu: Mater. Sci. Eng. A, 1996, vol. 220, pp. 215–22.10.1016/S0921-5093(97)80011-1 ↗
43. A. Kyusojin, K. Nishimoto, Y. Otobe, S. Kanai and Y. Ogasawara: Bull. Jpn. Soc. Mech. Eng., 1980, vol. 23 (182), pp. 1388–95.10.1299/jsme1958.23.1388 ↗
44. W.-Y. Li, T. Ma, and S. Yang: Adv. Eng. Mater., 2010, vol. 12 (1–2), pp. 35–43.10.1002/adem.200900185 ↗
45. Technical Data Sheet, Carpenter Technology Corporation, Wyomissing, PA, 2006.
46. M. Maalekian, E. Kozeschnik, H.P. Brantner, and H. Cerjak: Acta Mater., 2008, vol. 56, pp. 2843–55.10.1016/j.actamat.2008.02.016 ↗
47. A.A. Guimaraes and J.J. Jonas: Metall. Trans. A, 1981, vol. 12A, pp. 1655–66.10.1007/BF02643571 ↗
48. S.-F. Toh and W.M. Rainforth: Mater. Sci. Technol., 1996, vol. 12, pp. 1007–14.10.1080/02670836.1996.11665715 ↗
49. D. Blavette, A. Bostel, and J.M. Sarrau: Metall. Trans. A, 1985, vol. 16A, pp. 1703–11.10.1007/BF02670358 ↗
50. G.P. Sabol and R. Stickler: Phys. Status Solidi, 1969, vol. 35, pp. 11–52.10.1002/pssb.19690350102 ↗
51. H. Monajati, M. Jahazi, R. Bahrami, and S. Yue: Mater. Sci. Eng. A, 2004, vol. 373, pp. 286–93.10.1016/j.msea.2004.01.027 ↗
52. M. Durand-Charre: The Microstructure of Superalloys, CRC Press, Amsterdam, 1997, pp. 68–69.
53. B. Reppich, P. Schepp, and G. Wehner: Acta Metall., 1982, vol. 30, pp. 95–104.10.1016/0001-6160(82)90049-9 ↗
54. M.P. Jackson and R.C. Reed: Mater. Sci. Eng. A, 1999, vol. 259, pp. 85–97.10.1016/S0921-5093(98)00867-3 ↗
55. Waspaloy, Publication Number SMC-011, Special Metals Corporation, New Hartford, NY, Sept. 2004.
56. Z. Li, S.L. Gobbi, and J.H. Loreau: J. Mater. Process. Technol., 1997, vol. 65, pp. 183–90.10.1016/S0924-0136(96)02260-1 ↗
57. M. Soucail, A. Moal, L. Naze, E. Massoniz, C. Levaillant, and Y. Bienvenu: in Superalloys 1992, S.D. Antolovich, R.W. Stusrud, R.A. Mackay, D.L. Anton, T. Khan, R.D. Kissinger, and D.L. Klarstrom, eds., TMS, Warrendale, PA, 1992, pp. 847–56.10.7449/1992/Superalloys_1992_847_856 ↗
58. O.A. Ojo and M.C. Chaturvedi: Mater. Sci. Eng. A, 2005, vol. 403, pp. 77–86.10.1016/j.msea.2005.04.034 ↗