journal article·2009-04

Effect of Bimodal Grain Size Distribution on Scatter in Toughness

Debalay Chakrabarti, Martin Strangwood, Claire Davis

Publisher page

Abstract

Blunt-notch tests were performed at −160 °C to investigate the effect of a bimodal ferrite grain size distribution in steel on cleavage fracture toughness, by comparing local fracture stress values for heat-treated microstructures with uniformly fine, uniformly coarse, and bimodal grain structures. An analysis of fracture stress values indicates that bimodality can have a significant effect on toughness by generating high scatter in the fracture test results. Local cleavage fracture values were related to grain size distributions and it was shown that the largest grains in the microstructure, with an area percent greater than approximately 4 pct, gave rise to cleavage initiation. In the case of the bimodal grain size distribution, the large grains from both the “fine grain” and “coarse grain” population initiate cleavage; this spread in grain size values resulted in higher scatter in the fracture stress than in the unimodal distributions. The notch-bend test results have been used to explain the difference in scatter in the Charpy energies for the unimodal and bimodal ferrite grain size distributions of thermomechanically controlled rolled (TMCR) steel, in which the bimodal distribution showed higher scatter in the Charpy impact transition (IT) region.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · Material Properties and Failure Mechanisms

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. E. Orowan: Trans. Inst. Eng. Shipbuilders Scotland, Institute of Engineers and Shipbuilders in Scotland, Glasgow, Scotland, United Kingdom, 1946, vol. 80, pp. 165–96.
2. A.H. Cottrell: Trans. AIME, 1958, vol. 212, pp. 192–203.
3. E. Smith: Proc. Conf. Physical Basis of Yield and Fracture, Institute of Physics and Physical Society, Oxford, United Kingdom, 1966, pp. 36–45.
4. C.J. McMahon and M. Cohen: Acta Metall., 1965, vol. 13, pp. 591–604.10.1016/0001-6160(65)90121-5 ↗
5. J.F. Knott: Fundamentals of Fracture Mechanics, Butterworth and Co., London, 1973, pp. 170–85.
6. J.H. Chen and C. Yan: Metall. Trans. A, 1992, vol. 23A, pp. 2549–56.10.1007/BF02658058 ↗
7. D.A. Curry and J.F. Knott: Met. Sci., 1978, vol. 12, pp. 511–14.10.1016/0036-9748(78)90198-9 ↗
8. J.F. Knott: Conf. Proc. Steels for Line Pipe and Pipeline Fittings, The Metals Society, London, United Kingdom, 1983, pp. 79–89.
9. N.J. Petch: Acta Metall., 1986, vol. 34, pp. 1387–93.10.1016/0001-6160(86)90026-X ↗
10. A. Echeverria and J.M. Rodriguez-Ibabe: Mater. Sci. Eng., A, 2003, vol. 346, pp. 149–58.10.1016/S0921-5093(02)00538-5 ↗
11. D. Chakrabarti, C.L. Davis, and M. Strangwood: Mater. Charact., 2007, vol. 58, pp. 423–38.10.1016/j.matchar.2006.06.014 ↗
12. J.F. Knott: Proc. Int. Conf. Microalloyed Steels—Emerging Technologies and Applications, Vitasta Publishing Pvt. Ltd., New Delhi, India, 2007, pp. 10–23.
13. R.O. Ritchie, J.F. Knott, and J.R. Rice: J. Mech. Phys. Solids, 1973, vol. 21, pp. 395–410.10.1016/0022-5096(73)90008-2 ↗
14. D. Bhattacharjee, J.F. Knott, and C.L. Davis: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 121–30.10.1007/s11661-004-0115-7 ↗
15. S.J. Wu and C.L. Davis: Mater. Sci. Eng., A, 2004, vols. 387–389, pp. 456–60.
16. M.T. Shehata and J.D. Boyd: Proc. Conf. Advances in Physical Metallurgy and Applications of Steels, Liverpool, 1982, Metals Society, London, 1982, Book 284, pp. 229–36.
17. G.Z. Wang and J.H. Chen: Int. J. Fract., 1998, vol. 89, pp. 269–84.10.1023/A:1007464126165 ↗
18. S.J. Wu and J.F. Knott: J. Mech. Phys. Solids, 2004, vol. 52, pp. 907–24.10.1016/j.jmps.2003.07.005 ↗
19. J.H. Chen, L. Zhu, and H. Ma: Acta Metall. Mater., 1990, vol. 38, pp. 2527–35.10.1016/0956-7151(90)90264-H ↗
20. D. Chakrabarti: Doctoral Thesis, University of Birmingham, Birmingham, United Kingdom, 2007.
21. J.R. Griffiths and D.R.J. Owen: J. Mech. Phys. Solids, 1971, vol. 19, pp. 419–31.10.1016/0022-5096(71)90009-3 ↗
22. R. Ding, A. Islam, S. Wu, and J.F. Knott: Mater. Sci. Technol., 2005, vol. 21, pp. 467–75.10.1179/174328405X27115 ↗
23. L.P. Zhang: Doctoral Thesis, University of Birmingham, Birmingham, United Kingdom, 1999.
24. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill Book Company, London, 1988, pp. 275–338.
25. D. Tabor: Proc. R. Soc. London, Ser. A, 1947, vol. 192, pp. 247–74.
26. D. Bhattacharjee, C.L. Davis, and J.F. Knott: Ironmaking and Steelmaking, 2003, vol. 30, pp. 249–55.10.1179/030192303225003908 ↗
27. C.L. Davis: Doctoral Thesis, University of Cambridge, Cambridge, United Kingdom, 1994.
28. BSEN 14556: Standard on Steel: Charpy V-Notch Pendulum Impact Test, Instrumented Test Method, BSI British Standard, London, United Kingdom, 2000, pp. 1–28.
29. M. Mantyla, A. Rossoll, I. Nedbal, C. Prioul, and B. Marini: J. Nucl. Mater., 1999, vol. 264, pp. 257–62.10.1016/S0022-3115(98)00496-6 ↗
30. M.A. Linaza, J.L. Romero, J.M. Rodriguez-Ibabe, and J.J. Urcola: Scripta Metall., 1995, vol. 32, pp. 395–400;10.1016/S0956-716X(99)80071-5 ↗
31. W. Lei, D. Li, and M. Yao: Scripta Metall.; 1994, vol. 31 (1), pp. 5–7.10.1016/0956-716X(94)90085-X ↗
32. Y.K. Lee: J. Mater. Sci. Lett., 2002, vol. 21 (16) pp. 1253–55.10.1023/A:1016555119230 ↗
33. W. Steven and A.G. Haynes: JISI, 1956, vol. 183, pp. 349–59.
34. D.P. Fairchild, D.G. Howden, and W.A.T. Clark: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 641–52.10.1007/s11661-000-0007-4 ↗
35. M.J. Balart, C.L. Davis, and M. Strangwood: Mater. Sci. Eng., A, 2000, vol. 284, pp. 1–13.10.1016/S0921-5093(00)00803-0 ↗
36. J.H. Chen, G.Z. Wang, Q. Wang, and Y.G. Liu; Int. J. Fract., 2004, vol. 126, pp. 223–41.10.1023/B:FRAC.0000026545.74317.4c ↗
37. G.Z. Wang, Y.G. Liu, and J.H. Chen: Mater. Sci. Eng., A, 2004, vol. 369, pp. 181–91.10.1016/j.msea.2003.11.003 ↗
38. J.H. Chen and C. Yan: Mater. Sci. Technol., 1992, vol. 23A, pp. 509–17.
39. J.H. Chen, G.Z. Wang, and H. Ma: Metall. Trans. A, 1990, vol. 21A, pp. 321–30.10.1007/BF02782412 ↗
40. T. Gladman: The Physical Metallurgy of Microalloyed Steels, Book 615, The Institute of Materials, London, 1997, pp. 176–223.
41. S. Gunduz and R.C. Cochrane: Mater. Des., 2005, vol. 26, pp. 486–92.10.1016/j.matdes.2004.07.022 ↗
42. E.V. Morales, J. Gallego, and H.J. Kestenbach: Philos. Mag. Lett., 2003, vol. 83, pp. 79–87.10.1080/0950083021000056632 ↗
43. C.Z. Wang, J.H. Chen, and J.G. Wang: Int. J. Fract., 2002, vol. 118, pp. 211–27.10.1023/A:1022908402233 ↗
44. G.Z. Wang, J.G. Wang, and J.H. Chen; Eng. Fract. Mech., 2003, vol. 70, pp. 2499–2512.10.1016/S0013-7944(03)00080-8 ↗
45. M.G. Mendiratta, R.L. Goetz, and D.M. Dimiduk: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3903–12.10.1007/BF02595639 ↗
46. P. Bowen, S.G. Druce, and J.F. Knott: Acta Metall., 1986, vol. 34 (6), pp. 1121–31.10.1016/0001-6160(86)90222-1 ↗
47. J.I. San Martin and J.M. Rodriguez-Ibabe: Scripta Mater., 1999, vol. 40, pp. 459–64.10.1016/S1359-6462(98)00467-9 ↗
48. J.H. Chen, G.Z. Wang, C. Yan, H. Ma, and L. Zhu: Int. J. Fract., 1997, vol. 83, pp. 139–57.10.1023/A:1007309017416 ↗
49. A. From and R. Sandstrom: Mater. Charact., 1999, vol. 42, pp. 111–22.10.1016/S1044-5803(98)00051-5 ↗
50. F. Vodopivec, B. Arzensek, D. Kmetic, and J. Vojvodic-Tuma: Mater. Technol., 2003, vol. 37, pp. 317–26.
51. H. Qiu, R. Ito, and K. Hiraoka: Mater. Sci. Eng., A, 2006, vols. 435–436, pp. 648–52.10.1016/j.msea.2006.07.086 ↗
52. P. Hausild, C. Berdin, and P. Bompard: Mater. Sci. Eng., A, 2005, vol. 391, pp. 188–97.10.1016/j.msea.2004.08.067 ↗
53. P. Shanmugam and S.D. Pathak: Eng. Fract. Mech., 1996, vol. 53, pp. 991–1005.10.1016/0013-7944(95)00159-X ↗
54. D. Talbot: Doctoral Thesis, University of Birmingham, Birmingham, United Kingdom, 2002.
55. S.J. Wu and C.L. Davis; J. Microsc., 2004, vol. 213, pp. 262–72.10.1111/j.0022-2720.2004.01311.x ↗