Pulsed Nd:YAG laser welding of copper using oxygenated assist gases
Source abstract
Abstract
The effects of using oxygenated assist gases on the weldability and weld properties of Nd:YAG, pulsed laser welds in copper (Cu) have been evaluated. It was found that the effective absorptivity of the Cu increased as the oxygen content of the Ar assist gas was increased. This facilitated laser welding of Cu at much lower laser powers and increased weld penetration. The use of oxygenated assist gas promoted nucleation and growth of submicroscopic oxide particles within the weld metal. These particles dispersion-strengthened the weld metal, thereby increasing both weld metal hardness and strength. However, when O2 concentrations in the assist gas were greater than 90 pct, weld metal embrittlement due to excessive volume fractions of oxides was observed. The use of oxygenated assist gas also led to excessive cold lapping and poor bead quality. The bead quality was improved, however, by ramping-down the laser power before terminating each pulse.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Welding Techniques and Residual Stresses · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. S.P. Murarka, R.J. Gutmann, A.E. Kaloyeros, and W.A. Landford: Thin Solid Films, 1993, vol. 236, pp. 257–66.10.1016/0040-6090(93)90680-N ↗
2. M.A. Wojcicki and R.J. Pryputniewicz: ICALEO 1996 Laser Materials Processing, Detroit, MI, Oct. 14–17, 1996, Laser Institute of America, Orlando, FL, pp. 84–92.
3. M.A. Wojcicki and R.J. Pryputniewicz: 1997 Proc. 47th Electronic Components & Technology Conf., San Jose, CA, May 18–21, 1997, IEEE, Piscataway, NJ, pp. 905–10.
4. J.H. Scheel: Canadian Copper/Cuivre Canadien, 1995, No. 134, pp. 4–5.
5. K. Shimizu and K. Hashimoto: Fujitsu Sci. Technol., 1992, vol. 28 (3), pp. 310–15.
6. H. Lambilly and H. Keser: IEEE Trans. Compon. Hybrids Manuf. Technol., 1993, vol. 16 (4) pp. 412–17.10.1109/33.237930 ↗
7. F. Lechuga, E. Tyszka, J. Ramos, M. Bosman, and C. Timmermans: ICALEO ’99, San Diego, CA, Nov. 15–18, 1999, Laser Institute of America, Orlando, FL, 1999, pp. D197-D205.
8. J.A. Ramos and F. Lechuga: Proc. 19th ICALEO, Laser Materials Processing, Dearborn, MI, Oct. 2–5, 2000, H. Hugel, A. Matsunawa, and J. Mazumder, eds., Laser Institute of America, Orlando, FL, 2000, vol. 89, pp. C62-C71.
9. W.W. Duley: Laser Welding, John Wiley & Sons, Inc., New York, NY, 1999.
10. H. Gouveia: Proc. Latin American Regional Welding Congress, Rio de Janiero, Apr. 4–10, 1992, Associacao Brasileira de Soldagem, Sao Paulo, Brazil, 1992, vol. 1, pp. 319–36.
11. H. Gouveia, J. Norrish, and L. Quintino: Weld. Rev. Int., 1994, vol. 13 (2), pp. 266, 268–269, and 272–273.
12. H. Gouveia, I. Richardson, P. Kapadia, J. Dowden, and R. Ducharme: ICALEO ’94, Laser Materials Processing, Orlando, FL., Oct. 17–20 2000, T.D. McCay, A. Matsunawa, and H. Hugel, eds., Laser Institute of America, Orlando, FL, 1994, vol. 79, pp. 480–89.
13. H.N. Gouveia: Ph.D. Thesis, Cranfield University, Bedfordshire, U.K., 1994.
14. M. Dell’erba: Opt. Laser Technol., 1985, vol. 17 (5) pp. 261–62.10.1016/0030-3992(85)90040-4 ↗
15. M. Dell’Erba, P. Sforza, G. Chita, and L. Cento: Proc. 5th Int. Congress on Applications of Lasers and Electro-Optics, ICALEO ’86, Arlington, VA, Nov. 10–13, 1986, C.M. Banas, and G.L. Whitney, eds., Laser Institute of America, Orlando, FL, 1986, pp. 57–62.
16. G. Daurelio, and G. Giorleo: Mater. Manuf. Processing, 1991, vol. 6 (4) pp. 577–603.10.1080/10426919108934791 ↗
17. H.N. Bransch, D.C. Weckman, and H.W. Kerr: Weld. J., 1994, vol. 73 (6) pp. 141s-151s.
18. A. Matsunawa, S. Katayama, and K. Nishizawa: Welding, Joining, Coating and Surface Modification of Advanced Materials, Dalian, China, Sept. 1–2, 1994, Gansu University of Technology, Lanzou, Gansu, China, 1994, pp. 1–6.
19. E. Biro, Y. Zhou, D.C. Weckman, and K.J. Ely: J. Laser Appl., 2001, vol. 13 (3) pp. 96–104.10.2351/1.1356420 ↗
20. The Merck Index, M. Windholz, ed., Merck & Co., Inc., Rahway, NJ, 1983.
21. G. Vander Voort: Metallography, Principles and Practice, McGraw-Hill, Inc., New York, NY, 1984.10.31399/asm.tb.mpp.9781627082600 ↗
22. H. Kokawa: Tohoku University, Tohoku, Japan, private communication, 2001.
23. W. Kurz and R. Trivedi: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 625–34.10.1007/BF02648951 ↗
24. I. Ursu, L. Nanu, I.N. MihĂilescu, L.C. Nistor, V.S. Teodorescu, A.M. Prokhorov, V.I. Konov, and N.I. Chapliev: J. Phys. Lett., 1984, vol 45 (14), pp. L-737–L-740.10.1051/jphyslet:019840045014073700 ↗
25. I. Ursu, L.C. Nistor, V.S. Teodorescu, I.N. MihĂilescu, L. Nanu, A.M. Prokhorov, N.I. Chapliev, and V.I. Konov: Appl. Phys. Lett., 1984, vol. 44 (2), pp. 188–89.10.1063/1.94703 ↗
26. T. Tanaka: Jpn. J. Appl. Phys., 1979, vol. 18 (6) pp. 1043–47.10.1143/JJAP.18.1043 ↗
27. J. Xie, A. Kar, J.A. Rothenflue, and W.P. Latham: J. Laser Appl., 1997, vol. 9(2), pp. 77–85.10.2351/1.4745447 ↗
28. J.T. Liu, D.C. Weckman, and H.W. Kerr: Metall. Trans. B, 1993, vol. 24B (6), pp. 1065–76.10.1007/BF02660998 ↗
29. D.C. Weckman, H.W. Kerr, and J.T. Liu: Metall. Mater. Trans. B, 1997, vol. 28B, pp. 687–700.10.1007/s11663-997-0043-1 ↗
30. C.J. Nonhof: Material Processing with Nd-Lasers, Electrochemical Publications Ltd. Ayr, Scotland, 1988.
31. Oxide Handbook, 2nd ed., G.V. Samsonov, ed., IFI/Plenum Data Company, New York, NY, 1982.
32. Metals Handbook, 10th ed. vol. 2, Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM INTERNATIONAL, Materials Park, OH, 1990.