journal article·2002-09

The relationship between grain size and the surface roughening behavior of Al-Mg alloys

M. R. Stoudt, R. E. Ricker

Publisher page

Abstract

The inhomogeneous surface deformation generated during metal forming presents significant challenges to the use of high-strength, lightweight alloys in automotive applications through the initiation of strain localizations that produce both tearing during metal forming and increased friction between mating die surfaces. Thus, a generic understanding of the relationships between plastic strain, grain size, and deformation-induced roughness at the free surface is needed before forming models can be fully developed to accurately predict the behavior and, ultimately, the changes in the friction within the dies. This research examines the roughening behavior of a solid solution strengthened, commercial Al-Mg alloy. The results of this evaluation indicate that the standard roughness measures increase with uniaxial plastic strain in a manner that can be represented by a simple linear estimate. The results also demonstrate that the roughening rate (dR a/dɛ pl) is dependent on the grain size in this alloy, and the relationship between the roughening rate and grain size also appears to be linear for the range of grain sizes included in this evaluation. However, examinations of the roughened surfaces reflect that the roughening process is a highly complex combination of mechanisms and it is strongly influenced by grain size. As a result, representing the complex changes that occur during roughening of a free surface by plastic deformation with a single number calculated from profilometry scans may be too coarse of a measure to fully describe these changes when modeling roughness-dependent behavior or properties.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Advanced Surface Polishing Techniques · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. M. Li and D.J. Lege: J. Eng. Mater. Technol., 1998, vol. 120, pp. 48–56.10.1115/1.2806837 ↗
2. G.E. Dieter: Mech. Metall., 3rd ed., McGraw-Hill, New York, NY, 1986.
3. R. Becker: Acta Mater., 1998, vol. 46 (4), pp. 1385–1401.10.1016/S1359-6454(97)00182-1 ↗
4. S.W. Lo and T.C. Horng: J. Tribology, 1999, vol. 121, pp. 224–33.10.1115/1.2833925 ↗
5. P.K. Saha, W.R.D. Wilson, and R.S. Timsit: Wear, 1996, vol. 197, pp. 123–29.10.1016/0043-1648(95)06881-3 ↗
6. W.R.D. Wilson: J. Manu. Sci. Eng., 1997, vol. 119, pp. 695–98.10.1115/1.2836811 ↗
7. G.I. Taylor: J. Inst. Met., 1938, vol. 62, pp. 307–24.
8. J.D. Eshelby: Proc. R. Soc. London A, 1957, vol. A241, pp. 376–96.
9. M.F. Ashby: Phil. Mag., 1970, vol. 21, pp. 399–424.10.1080/14786437008238426 ↗
10. W.R.D. Wilson and W. Lee: J. Manu. Sci. & Engr., 123, 2001, pp. 279–83.10.1115/1.1363596 ↗
11. Y.Z. Dai and F.P. Chiang: J. Eng. Mater. Technol., 1992, vol. 114, pp. 432–38.10.1115/1.2904196 ↗
12. A.E. Valkonen: Plastic Deformation and Roughness of Free Metal Surfaces, Ohio State University, Columbus, OH, 1987.
13. T. Abe, S. Nagaki, and T. Akase: Bull. JSME, 1985, vol. 28 (236), pp. 251–58.10.1299/jsme1958.28.251 ↗
14. O. Kienzle and K. Mieztner: Stahl V. Eisen, 1961, vol. 81 (14), pp. 950–52.
15. K. Osakada and M. Oyane: Bull. JSME, 1971, vol. 14 (68), pp. 171–77.10.1299/jsme1958.14.171 ↗
16. U. Essmann, M. Rapp, and M. Wilkens: Acta Metall., 1968, vol. 16, pp. 1275–87.10.1016/0001-6160(68)90008-4 ↗
17. V. Tvergaard and A. Needleman: Proc. R. Soc. London A, 1993, vol. 443, pp. 547–62.10.1098/rspa.1993.0161 ↗
18. J.M. Robinson: I. Mater. Rev., 1994, vol. 39 (6), pp. 217–27.10.1179/imr.1994.39.6.217 ↗
19. Aluminum Standards and Data 1988, 9th ed., The Aluminum Association, Washington, DC, 1988.
20. J.M. Robinson and M.P. Shaw: Mater. Sci. Engr., 1994, vol. A174, pp. 1–7.10.1016/0921-5093(94)91106-1 ↗
21. W.F. Smith: Structure and Properties of Engineering Alloys, McGraw-Hill Book Company, New York, NY, 1981.
22. Properties and Selection: Nonferrous Alloys and Pure Metals, 9th ed., ASM INTERNATIONAL, Metals Park, OH, 1979, vol. 2.
23. M.R. Stoudt and R.E. Ricker: in Innovations in Processing and Manufacturing of Sheet Materials, M. Demeri, ed., TMS, Warrendale, PA, 2001, pp. 237–44.
24. P.S. Lee, H.R. Piehler, B.L. Adams, G. Jarvis, H. Hampel, and A.D. Rollett: J. Mater. Proc. Technol., 1998, vol. 80 (1), pp. 315–19.10.1016/S0924-0136(98)00189-7 ↗
25. Anon.: in 2000 Annual Book of ASTM Standards, Section 3, Metals Test Methods and Analytical Procedures, vol. 3.01 Metals—Mechanical Testing; Elevated and Low-Temperature Tests; Metallography, ASTM, Philadelphia, PA, 2000, pp. 240–63.
26. G.F. VanderVoort: Metallography Principles and Practice, ASM INTERNATIONAL, Materials Park, OH, 1999.
27. T.R. Thomas: Rough Surfaces, Longman, London, 1982.
28. R.E. Walpole and R.H. Myers: Probability and Statistics for Engineers and Scientists, The Macmillian Co., New York, NY, 1972.