Comparison between high and low strain-rate deformation of tantalum
Source abstract
Abstract
To understand the constitutive behavior of tantalum, compression tests are performed over the range of strain rates from 0.0001/s to 3000/s, and at temperatures from 296 to 1000 K. The flow stress is seen to be representable as the sum of a thermal, an athermal, and a viscous drag component. At high strain rates (3000/s), the thermal component is observed to be expressible in terms of the temperature and the strain rate, whereas the athermal component is independent of these variables. At lower strain rates, however, such a separation of the effects of the strain, strain rate, and temperature on the flow stress is not easily achieved. At high enough temperatures, i.e., temperatures above which the thermal component is essentially zero, viscous drag appears to have a significant effect on the flow stress.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Nuclear Materials and Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. P.S. Follansbee and U.F. Kocks: Acta Metall., 1988, vol. 36, pp. 81–93.10.1016/0001-6160(88)90030-2 ↗
2. W.H. Gourdin, and D. Lassila: Tantalum. Proc. Symp. Held at 125th TMS Annual Meeting and Exhibition, E. Chen, A. Crowson, E. Lavernia, and W. Ebihara, eds., TMS, Warrendale, PA, 1995 pp. 219–23.
3. U.F. Kocks: J. Eng. Mater. Technol., 1976, vol. 98, pp. 76–85.10.1115/1.3443340 ↗
4. H. Mecking, and U.F. Kocks: Acta Metall., 1981, vol. 29, pp. 1865–75.10.1016/0001-6160(81)90112-7 ↗
5. Y. Estrin, and H. Mecking: Acta Metall., 1984, vol. 32, pp. 57–70.10.1016/0001-6160(84)90202-5 ↗
6. P.S. Follansbee, J.C. Huang, and G.T. Gray: Acta Metall. Mater., 1990, vol. 38, pp. 1241–54.10.1016/0956-7151(90)90195-M ↗
7. H. Mecking and Y. Estrin: Constitutive Relations and Their Physical Basis: Proc. 8th Riso Int. Symp. on Metallurgy and Materials Science, S.I. Anderson, ed., Technical University Hamburg, Hamburg, 1990 pp. 123–45.
8. G. Simmons and H. Wang: Single Crystal Elastic Constants and Calculated Aggregate Properties: A Handbook, 2nd ed. The MIT Press, Cambridge, MA, 1971.
9. U.F. Kocks, A.S. Argon, and M.F. Ashby: Progr. Mater. Sci., 1975, vol. 19, pp. 1–271.10.1016/0079-6425(75)90005-5 ↗
10. A.K. Zurek, P.S. Follansbee, and D. Kapoor: in High Strain Rate Behavior of Refractory Metals and Alloys, R. Asfahani, E. Chen, and A. Crowson, eds., TMS, Warrendale, PA, 1992 pp. 190–207.
11. S. Nemat-Nasser, and J.B. Isaacs: Acta Mater., 1997, vol. 45, pp. 907–19.10.1016/S1359-6454(96)00243-1 ↗
12. S. Nemat-Nasser and Y. Li: Acta Mater., 1998, vol. 46, pp. 565–77.10.1016/S1359-6454(97)00230-9 ↗
13. A.H. Cottrell and R.J. Stokes: Proc. R. Soc. A, 1955, vol. 233, pp. 17–34.10.1098/rspa.1955.0243 ↗
14. Z.S. Basinski and J.W. Christian: Aus. J. Phys., 1960, vol. 13, pp. 299–308.10.1071/PH600299a ↗
15. J. Klepaczko: Mater. Sci. Eng., 1975, vol. 18, pp. 121–35.10.1016/0025-5416(75)90078-6 ↗
16. J.R. Klepaczko and C.Y. Chiem: J. Mech. Phys. Solids, 1986, vol. 34, pp. 29–54.10.1016/0022-5096(86)90004-9 ↗
17. K.G. Hoge and A.K. Mukherjee: J. Mater. Sci., 1977, vol. 12, pp. 1666–72.10.1007/BF00542818 ↗
18. M.A. Meyers, Y.J. Chen, F.D.S. Marquis, and D.S. Kim: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2493–2502.10.1007/BF02669407 ↗
19. S.R. Chen, G.T. Gray III, and S.R. Bingert: in Tantalum. Proc. Symp. Head at 125th TMS Annual Meeting and Exhibition, E. Chen, A. Crowson, E. Lavernia, and W. Ebihara, eds., TMS, Warrendale, PA, 1996 pp. 173–84.
20. D.J. Steinberg, and C.M. Lund: J. Appl. Phys., 1989, vol. 65, pp. 1528–33.10.1063/1.342968 ↗
21. G.T. Gray III and K.S. Vecchio: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2555–64.10.1007/BF02669413 ↗
22. C.M. Lopatin, C.L. Wittman, J.P. Swensen, and P.F. Perron: in High Strain Rate Behavior of Refractory Metals and Alloys, R. Asfahani, E. Chen, and A. Crowson, eds., TMS, Warrendale, PA, 1992 pp. 241–47.
23. R.M. Davies: Phil. Mag., 1948, vol. 240, pp. 375.
24. H. Kolsky: Proc. Phys. Soc. London, 1949, vol. 62, pp. 676–700.10.1088/0370-1301/62/11/302 ↗
25. P.S. Follandsbee: Mechanical Testing, Metals Handbook, 9th ed., ASM, Metals Park, OH, 1985, vol. 8, p. 190.
26. S. Nemat-Nasser, J.B. Isaacs, and J. E. Starrett: Proc. R. Soc. London A, 1991, vol. 435, pp. 371–91.10.1098/rspa.1991.0150 ↗
27. R. Kapoor, and S. Nemat-Nasser: Mech. Mater. 1998, vol. 27, pp. 1–12.10.1016/S0167-6636(97)00036-7 ↗
28. S. Nemat-Nasser, Y. Li, and J.B. Isaacs: Mech. Mater., 1994, vol. 17, pp. 111–34.10.1016/0167-6636(94)90053-1 ↗
29. E. Nadgornyi: Progr. Mater. Sci., 1988, vol. 31, pp. 19–21 and 232–51.10.1016/0079-6425(88)90005-9 ↗
30. G. Regazzoni, U.F. Kocks, and P.S. Follansbee: Acta Metall., 1987, vol. 35, pp. 2865–75.10.1016/0001-6160(87)90285-9 ↗
31. G.Y. Chin, and W.L. Mammel: Trans. TMS-AIME, 1967, vol. 239, pp. 1400–05.