The Influence of Fluid Flow on the Microstructure of Directionally Solidified AlSi-Base Alloys
Source abstract
Abstract
To obtain a quantitative understanding of the effect of fluid flow on the microstructure of cast alloys, a technical Al-7 wt pct Si-0.6 wt pct Mg alloy (A357) has been directionally solidified with a medium temperature gradient under well-defined thermal and fluid-flow conditions. The solidification was studied in an aerogel-based furnace, which established flat isotherms and allowed the direct optical observation of the solidification process. A coil system around the sample induces a homogeneous rotating magnetic field (RMF) and, hence, a well-defined flow field close to the growing solid-liquid interface. The application of RMFs during directional solidification results in pronounced segregation effects: a change to pure eutectic solidification at the axis of the sample at high magnetic field strengths is observed. The investigations show that with increasing magnetic induction and, therefore, fluid flow, the primary dendrite spacing decreases, whereas the secondary dendrite arm spacing increases. An apparent flow effect on the eutectic spacing is observed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Solidification and crystal growth phenomena · Aluminum Alloy Microstructure Properties · Metallurgical Processes and Thermodynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. M.E. Glicksman, M.B. Koss, L.T. Bushnell, J.C. LaCombe, and E.A. Winsa: Materials and Fluids under Low Gravity, Lecture Notes in Physics, L. Ratke, H. Walter, and B. Feuerbacher, eds., Springer Verlag, Heidelberg, 1996, pp. 63–75
2. S. Steinbach, L. Ratke, and H.D. Masslow: Proc. 17th Symp. on European Rocket and Balloon Programmes and Related Research, Sandefjord, Norway, ESA SP-590, 2005, pp. 521–26
3. W. Kurz, D.J. Fisher: Fundamentals of Solidification, Trans Tech Publications, Aedermannsdorf, Switzerland, 1989, pp. 1–316
4. C. Beckermann, H.-J. Diepers, I. Steinbach, A. Karma, X. Tong: J. Comp. Phys., 1999, vol. 154, pp. 468–9610.1006/jcph.1999.6323 ↗
5. H.-J. Diepers, C. Beckermann, I. Steinbach: Acta Mater., 1999, vol. 47, pp. 3663–7810.1016/S1359-6454(99)00239-6 ↗
6. K. Moenipur, K. Eigenfeld: Giessereiforschung, 2004, vol. 50, pp. 103–09
7. C. Beckermann: Int. Mater. Rev., 2002, vol. 47, pp. 243–6110.1179/095066002225006557 ↗
8. M.C. Flemings, G.E. Nereop: Trans. AIME, 1967, vol. 239, pp. 1449–61
9. P.A. Davidson, F. Boysan: Appl. Sci. Res., 1987, vol. 44, pp. 241–5910.1007/BF00412016 ↗
10. M. Hainke, J. Friedrich, G. Müller: J. Mater. Sci., 2004, vol. 39, pp. 2011–1510.1023/B:JMSC.0000017762.16763.2b ↗
11. R. Trivedi, W. Kurz: Int. Mater. Rev., 1994, vol. 39, pp. 49–7410.1179/imr.1994.39.2.49 ↗
12. J. Alkemper, S. Sous, C. Stöcker, L. Ratke: J. Cryst. Growth, 1998, vol. 191, pp. 252–6010.1016/S0022-0248(98)00114-6 ↗
13. S. Sous, L. Ratke: Z. Metallkd., 2005, vol. 96(4), pp. 362–69
14. J. Alkemper, L. Ratke, and S. Sous: Proc. 4th Decennial Conf. Solidification Processing, Sheffield, J. Beech and H. Jones, eds., Sheffield University, Sheffield, 1997, pp. 463–67
15. J. Fricke: J. Non-Crystal. Solids, 1992, vol. 145, pp. 1–25810.1016/S0022-3093(05)80419-3 ↗
16. P.H. Tewari, A.J. Hunt, J.G. Lieber, and K. Lufftus: Aerogels, J. Fricke, ed., Springer Verlag, Berlin, 1985, p. 14210.1007/978-3-642-93313-4_18 ↗
17. S. Steinbach, L. Ratke: Mater. Sci. Forum, 2006, vol. 508, pp. 491–9610.4028/www.scientific.net/MSF.508.491 ↗
18. M. Hainke: Ph.D. Thesis, Technical Faculty Erlangen-Nuremberg, Erlangen, Germany, 2004
19. J.T. Mason, J.D. Verhoeven, R. Trivedi: J. Cryst. Growth, 1982, vol. 59, pp. 516–2410.1016/0022-0248(82)90372-4 ↗
20. R. Grugel, W. Kurz: Metall. Trans. A, 1987, vol. 18A, pp. 1137–4210.1007/BF02668564 ↗
21. B. Toloui, A. Hellawell: Acta Metall., 1976, vol. 24, pp. 565–7310.1016/0001-6160(76)90102-4 ↗
22. N. Whisler, T.Z. Kattamis: J. Cryst. Growth, 1972, vol. 15, pp. 20–2410.1016/0022-0248(72)90315-6 ↗
23. D.H. Kirkwood: Mater. Sci. Eng., 1985, vol. 73, pp. L1–L410.1016/0025-5416(85)90319-2 ↗
24. K.A. Jackson, J.D. Hunt: Trans. AIME, 1966, vol. 236, pp. 1129–42
25. P.A. Davidson: An Introduction to Magnetohydrodynamics, Cambridge University Press, Cambridge, United Kingdom, 2001, pp. 1–42710.1017/CBO9780511626333 ↗
26. J.D. Hunt: Sci. Technol. Adv. Mater., 2001, vol. 2(1), pp. 147–5510.1016/S1468-6996(01)00040-7 ↗
27. J.D. Hunt, S.Z. Lu: Metall. Mater. Trans. A, 1996, vol. A27, pp. 611–2310.1007/BF02648950 ↗
28. S. Steinbach: Ph.D. Thesis, RWTH, Aachen, 2005
29. P. Lehmann, R. Moreau, D. Camel, R. Bolcato: J. Cryst. Growth, 1998, vol. 183, pp. 690–70410.1016/S0022-0248(97)00468-5 ↗
30. M. Rappaz, W.J. Boettinger: Acta Mater., 1999, vol. 47(11), pp. 3205–1910.1016/S1359-6454(99)00188-3 ↗
31. A.M. Mullis: J. Mater. Sci., 2003, vol. 38, pp. 2517–2310.1023/A:1023977723475 ↗
32. L. Ratke, W.K. Thieringer: Acta Metall., 1985, vol. 33, pp. 1793–180210.1016/0001-6160(85)90003-3 ↗
33. L. Ratke, P.W. Voorhees: Growth and Coarsening: Ostwald Ripening in Material Processing (Engineering Materials), Springer Verlag, Berlin, 2002, pp. 1–29510.1007/978-3-662-04884-9 ↗
34. S. Steinbach, L. Ratke: Micrograv. Sci. Technol., 2005, vol. XVI-1, pp. 111–1510.1007/BF02945959 ↗
35. W.R. Wilcox, L.L. Regel: Acta Astronautica, 1996, vol. 38(4–8), pp. 511–1610.1016/0094-5765(96)00031-8 ↗
36. J.E. Gruzleski, B. Closset: The Treatment of Liquid Aluminum Silicon Alloy, AFS, Inc., Des Plaines, IL, USA, 1990, ISBN 0874331218