journal article·2008-12

Recrystallization during Thermomechanical Processing of IMI834

P. Vo, M. Jahazi, S. Yue

Publisher page

Abstract

The microstructure development of the near-α titanium alloy IMI834 displaying an initial bimodal α + β microstructure has been characterized with respect to dynamic and static β recrystallization, through quantitative metallography. The investigation was supplemented by interrupted compression testing, to evaluate the applicability of fractional softening in the determination of static recrystallization kinetics for titanium alloys. Micrographs are presented that indicate that dynamic recrystallization occurred under test conditions (temperatures of 975 °C, 1000 °C, 1025 °C, 1060 °C, and 1100 °C and strain rates of 0.01, 0.1, and 1 s−1), although complete grain refinement and homogeneity were only achieved following static recrystallization. Measurement obtained via image analysis revealed recrystallization kinetics that increased with temperature, for single-phase β predeformation microstructures (1060 °C to 1100 °C). However, bimodal α + β microstructures (1000 °C to 1025 °C) displayed more rapid recrystallization rates with decreasing temperature, which was attributed to a corresponding increase in α phase fraction. This increase yielded a more refined initial β grain size and an increase in favorable nucleation sites. In two-phase α + β microstructures (975 °C) with secondary α in the β matrix, recrystallized grains could not be directly observed with optical microscopy. However, interrupted compression testing indicated that static recrystallization may be comparable to that observed at 1000 °C. At all temperatures, an increasing strain rate accelerated recrystallization kinetics.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Metallurgy and Material Forming · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. R.R. Boyer: Mater. Sci. Eng., 1996, vol. A213, pp. 103–1410.1016/0921-5093(96)10233-1 ↗
2. H.M. Flower: Mater. Sci. Technol., 1990, vol. 6, pp. 1082–9210.1179/mst.1990.6.11.1082 ↗
3. J.W. Brooks: in Titanium Alloys at Elevated Temperature: Structural Development and Service Behaviour, M. Winstone, ed., Institute of Materials, London, 2001, pp. 17–28
4. S.L. Semiatin, V. Seetharaman, and I. Weiss: in Advances in the Science and Technology of Titanium Alloy Processing, I. Weiss, R. Srinivasan, P.J. Bania, D. Eylon, S.L. Semiatin, eds., TMS, Warrendale, PA, 1997, pp. 3–73.
5. R. Tricot: Mem. Etud. Sci. Rev. Metall., 1989, vol. 86 (10), pp. 609–23
6. G. Lutjering, and J.C. Williams: Titanium, Springer-Verlag, Berlin, 2003, pp. 70–7610.1007/978-3-540-71398-2 ↗
7. J.G. Malcor, F. Montheillet, and B. Champin, in: Titanium Science and Technology, G. Lutjering, U. Zwicker., W. Bunk, eds., Deutsche Gesellschaft für Metallkunde, Oberursel, Germany, 1985, pp. 1495–1502
8. D.L. Bourell, and H.J. McQueen: J. Mater. Shaping Technol., 1987, vol. 5 (1), pp. 53–7310.1007/BF02833686 ↗
9. T. Sheppard, and J. Norley: Mater. Sci. Technol., 1998, vol. 4, pp. 903–0810.1179/mst.1988.4.10.903 ↗
10. Z.X. Guo, and R. Ding: in Ti-2003 Science and Technology, G. Lutjering, J. Albrecht, eds., Wiley-VCH, Weinheim, 2004, pp. 1267–74
11. Y.V.R.K Prasad, T. Seshacharyulu, S.C. Medeiros, and W.G. Frazier: Eng. Mater. Technol., 2001, vol. 123, pp. 355–6010.1115/1.1372708 ↗
12. J.F. Uginet: in Titanium ‘92 Science and Technology, F.H. Froes, I. Caplan, eds., TMS, Warrendale, PA, 1993, pp. 463–71
13. P.J. Postans, and R.H. Jeal: in Titanium ‘80 Science and Technology, H. Kimura, O. Izuma, eds., AIME, Kyoto, 1980, pp. 441–55
14. F. Ma, W. Lu, J. Qin, and D. Zhang: Mater. Sci. Eng., 2006, vol. A416, pp. 59–6510.1016/j.msea.2005.09.082 ↗
15. M. Jackson, R.J. Dashwood, L. Christodoulou, and H.M. Flower: in Titanium Alloys at Elevated Temperature: Structural Development and Service Behaviour, M.R. Winstone, ed., Institute of Materials Communications, London, 2001, pp. 89–101
16. T. Furuhara, Y. Toji, H. Abe, and T. Maki: Mater. Sci. Forum, 2003, vols. 426–432, pp. 655–6010.4028/www.scientific.net/MSF.426-432.655 ↗
17. P.S. Bate, P.L. Blackwell, and J.W. Brooks: 6th World Conf. on Titanium, P. Lacombe, R. Tricot, G. Beranger, eds., Les Editions de Physique, Les Ulis, France, 1998, pp. 287–92
18. R.W. Evans, G.S. Clark, and S.G. McKenzie: in MECAMAT ‘91 Large Plastic Deformations: Fundamental Aspects and Applications to Metal Forming, C. Teodosiu, J.L. Raphanel, F. Sidoroff, eds., A.A. Balkema, Rotterdam, 1993, pp. 395–403
19. P. Wanjara, M. Jahazi, H. Monajati, and S. Yue: Mater. Sci. Eng., 2006, vol. A416, pp. 300–1110.1016/j.msea.2005.10.042 ↗
20. G. Shen, D. Furrer, and J. Rollins: in Advances in the Science and Technology of Titanium Alloy Processing, I. Weiss, R. Srinivasan, P.J. Bania, D. Eylon, S.L. Semiatin, eds., TMS, Warrendale, PA, 1997, pp. 75–82
21. C.A. Dandre, S.M. Roberts, R.W. Evans, and R.C. Reed: Mater. Sci. Technol., 2000, vol. 16, pp. 14–2510.1179/026708300773002627 ↗
22. G. Shen, S.L. Semiatin, and R. Shivpuri: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1795–180310.1007/BF02670767 ↗
23. S.P. Fox, and D.F. Neal: in Titanium ‘95 Science and Technology, P.A. Blenkinsop, W.J. Evans, H.M. Flower, eds., Institute of Metals, London, 1996, pp. 628–35
24. G.S. Clark: Key Eng. Mater., 1993, vols. 77–78, pp. 141–48
25. I. Weiss, F.H. Froes, and D. Eylon: Metall. Trans. A, 1984, vol. 15A, pp. 1493–9610.1007/BF02648580 ↗
26. M. Dallaire, and D. Furrer: in Aerospace Materials & Manufacturing: Emerging Materials, Processes and Repair Techniques, M. Jahazi, M. Elboujdaini, P. Patnaik, eds., CIM, Montreal, 2006, pp. 589–95
27. J. Tiley, T. Searles, E. Lee, S. Kar, R. Banerjee, J.C. Russ, and H.L. Fraser: Mater. Sci. Eng., 2004, vol. A372, pp. 191–9810.1016/j.msea.2003.12.008 ↗
28. J. Chraponski, and W. Szkliniarz: Mater. Charact., 2001, vol. 46, pp. 149–5410.1016/S1044-5803(01)00117-6 ↗
29. L. Germain, N. Gey, M. Humbert, A. Hazotte, P. Bocher, and M. Jahazi: Mater. Charact., 2005, vol. 54, pp. 216–2210.1016/j.matchar.2004.11.011 ↗
30. W.G. Burgers: Physica, 1934, vol. 1, pp. 561–8610.1016/S0031-8914(34)80244-3 ↗
31. J.J. Jonas: Int. Conf. High Strength Low Alloy Steels, D.P. Dunne, T. Chandra, eds., South Coast Printers, Port Kembla, N.S.W., Australia, 1984, pp. 80–91
32. H. Zhang, G.Y. Lin, D.S. Peng, L.B. Yang, and Q.Q. Lin: Mater. Process. Technol., 2004, vol. 148, pp. 245–4910.1016/j.jmatprotec.2003.12.020 ↗
33. P. Vo, M. Jahazi, S. Yue, and P. Bocher: Mater. Sci. Eng., 2007, vol. A447, pp. 99–11010.1016/j.msea.2006.10.032 ↗
34. D.F. Neal: in Materials Design Approaches and Experiences, J.-C. Zhao, M. Fahrmann, T.M. Pollock, eds., TMS, Warrendale, PA, 2001, pp. 199–213
35. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, Elsevier Science, Ltd., Oxford, United Kingdom, 1996, pp. 173–220 and 277–7910.1016/B978-0-08-041884-1.50013-1 ↗
36. A.-M. Chaze and F. Montheillet: in Les Alliages de Titane Beta, A. Vassel, D. Eylon, and Y. Combres, eds., Editions de la Revue de Metallurgie, Paris, 1994, No. 8, pp. 41–48
37. P. Dadras, J.F. Thomas Jr., and J.C. Moosbrugger: Metall. Trans. A, 1983, vol. 14A, pp. 1512–16
38. I. Phillipart, and H.J. Rack: Mater. Sci. Eng., 1998, vol. A243, pp. 196–20010.1016/S0921-5093(97)00800-9 ↗
39. E.B. Shell, and S.L. Semiatin: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3219–2910.1007/s11661-999-0232-4 ↗
40. A.M. Elwazri, P. Wanjara, and S. Yue: ISIJ Int., 2003, vol. 43 (7), pp. 1080–8810.2355/isijinternational.43.1080 ↗
41. A.I. Fernandez, B. Lopez, and J.M. Rodrigues-Ibabe: Scripta Mater., 1999, vol. 40 (5), pp. 543–4910.1016/S1359-6462(98)00452-7 ↗
42. R. Ding, and Z.X Guo: Mater. Sci. Eng., 2004, vol. A365, pp. 172–7910.1016/j.msea.2003.09.024 ↗
43. H.J. McQueen, and J.J. Jonas: J. Appl. Metalworking, 1984, vol. 3 (3), pp. 233–4110.1007/BF02833651 ↗
44. P. Wanjara, M. Jahazi, H. Monajati, S. Yue, and J.-P. Immarigeon: Mater. Sci. Eng., 2005, vol. A396, pp. 50–6010.1016/j.msea.2004.12.005 ↗
45. H. Monajati, M. Jahazi, S. Yue, and A.K. Taheri: Metall. Mater. Trans., 2005, vol. 36A, pp. 895–90510.1007/s11661-005-0284-z ↗