journal article·2010-06

Synthesis, Tensile Testing, and Microstructural Characterization of Nanometric SiC Particulate-Reinforced Al 7075 Matrix Composites

A. Ahmed, A. J. Neely, K. Shankar, P. Nolan, S. Moricca, T. Eddowes

Publisher page

Abstract

This article examines the reasons for the poor performance of the nanometric scale SiC (n-SiCp) particulate-reinforced Al 7075 composites. The composites having different volume fractions of the n-SiCp were synthesized via powder metallurgy (P/M) route and were uniaxially tested at room temperature. Experimental results showed a significant drop in the hardness and tensile properties of the composites in comparison with those of the monolithic Al. Microstructural analysis via scanning electron microscopy (SEM) revealed large segregation of Mg in the vicinity of the n-SiCp and at the grain boundaries of the Al matrix, which plausibly changed both the aging kinetics and tensile behavior of the Al matrix. The segregation of Mg increased with an increase in the volume fraction of the n-SiCp in the Al matrix. No Mg segregation was found in the monolithic Al. The clustering of the n-SiCp was observed from SEM with energy dispersive X-ray analysis. SEM also revealed cracks in the n-SiCp clusters and debonding between the clusters and Al matrix, which were considered as the main mode of fracture in the composites.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. D.L. McDanels: Metall. Trans. A, 1985, vol. 16A, pp. 1105–15.10.1007/BF02811679 ↗
2. T.S. Srivatsan: J. Mater. Sci., 1996, vol. 12, pp. 1375–88.10.1007/BF00353120 ↗
3. M. Taya and R.J. Arsenault: Metal Matrix Composites Thermomechanical Behaviour, Pergamon Press, New York, NY, 1989, pp. 2–5.
4. T.W. Clyne and P.J. Withers: An Introduction to Metal Matrix Composites, University Press, Cambridge, United Kingdom, 1993, p. 5.10.1017/CBO9780511623080 ↗
5. T.J.A. Doel and P. Bowen: Compos. Part A, 1996, vol. 27, pp. 655–65.10.1016/1359-835X(96)00040-1 ↗
6. A. Razaghian, D. Yu, and T. Chandra: Compos. Sci. Technol., 1998, vol. 58, pp. 293–98.10.1016/S0266-3538(97)00130-9 ↗
7. A.B. Pandey, B.S. Majumdar, and D.B. Miracle: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 921–36.10.1007/s11661-000-1011-4 ↗
8. Y.C. Kang: Ph.D. Thesis, National Taiwan University, Taipei, Taiwan, ROC, 2004, pp. 134–45.
9. Z. Ren: M.E. Thesis, University of New South Wales, Sydney, Australia, 2007, p. 50.
10. A. Ahmed, A.J. Neely, K. Shankar, and S.L.I Chan: Mater. Sci. Forum, 2007, vols. 561–565, pp. 761–64.10.4028/www.scientific.net/MSF.561-565.761 ↗
11. J.K. Shang and R.O. Ritchie: Acta Metall., 1989, vol. 37, pp. 2267–78.10.1016/0001-6160(89)90154-5 ↗
12. A.N. Tiwari, V. Gopinathan, and P. Ramakrishan: Mater. Manuf. Processes, 1991, vol. 6, pp. 612–33.10.1080/10426919108934793 ↗
13. A. Kalkanli, S. Yilmaz: Mater. Des., 2008, vol. 29, pp. 775–80.10.1016/j.matdes.2007.01.007 ↗
14. C.H.J. Davies: J. Mater. Process. Technol., 1996, vol. 62, pp. 225–28.10.1016/0924-0136(95)02216-3 ↗
15. L.E.G. Cambronero, E. Sanchez, J.M. Ruiz-Roman, and J.M. Ruiz-Prieto: J. Mater. Process. Technol., 2003, vols. 143–144, pp. 378–83.10.1016/S0924-0136(03)00424-2 ↗
16. N.V. Ravi Kumar and E.S. Dwarakadasa: J. Mater. Sci., 1994, vol. 29, pp. 1533–39.10.1007/BF00368921 ↗
17. N. Chawla and K.K. Chawla: Metal Matrix Composites, Springer, New York, NY, 2006, pp. 88–90.10.1007/b101197 ↗
18. F. Thummler and R. Oberacker: Introduction to Powder Metallurgy, University Press, Cambridge, United Kingdom, 1993, pp. 10–12.
19. T.S. Srivatsan and V.K. Vasudevan: Int. J. Fatigue, 1998, vol. 20, pp. 187–202.10.1016/0142-1123(95)00093-3 ↗
20. X.G. Ning, J. Pan, J.H. Li, K.Y. Hu, H.Q. Ye, and H. Fukunaga: J. Mater. Sci. Lett., 1993, vol. 12, pp. 1644–47.10.1007/BF00627039 ↗
21. M. Strangwood, C.A. Hippsley, and J.J. Lewandowski: Scripta Metall. Mater., 1990, vol. 24, pp. 1483–87.10.1016/0956-716X(90)90418-G ↗
22. D.P. Myriounis, S.T. Hasan, and T.E. Matikas: Compos. Interfaces, 2008, vol. 15, pp. 495–514.10.1163/156855408784655292 ↗
23. Z. Shi, M. Gu, J. Liu, G. Liu, J.-C. Lee, D. Zhang, and R. Wu: Chin. Sci. Bull., 2001, vol. 46, pp. 1948–52.10.1007/BF02901903 ↗
24. W.M. Zhong, L’Esperance, and M. Suery: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2637–49.10.1007/BF02669421 ↗
25. J.H. Westbrook: Metall. Rev., 1964, vol. 9, pp. 415–70.
26. D. McLean: Grain Boundaries in Metals, University Press, Oxford, United Kingdom, 1957, p. 118.
27. J.R. Rellick and C.J. McMahon: Metall. Trans., 1974, vol. 5, pp. 2439–50.10.1007/BF02644027 ↗
28. D.R. Harries and A.D. Marwick: Phil. Trans. R. Soc. London A, 1980, vol. 295, pp. 197–207.10.1098/rsta.1980.0100 ↗
29. D.R. Gaskell: Introduction to Metallurgical Thermodynamics, Hemisphere, New York, NY, 1981, p. 287.
30. R. Arone, O. Botstein, and B. Shpigler: Isr. J. Technol., 1988, vol. 24, pp. 393–99.
31. S.V. Kamat, J.O. Hirth, and R. Mehrabian: Acta Metall., 1989, vol. 37, pp. 2395–2402.10.1016/0001-6160(89)90037-0 ↗
32. Y. Flom and R.J. Arsenault: Acta Metall., 1989, vol. 37, pp. 2413–23.10.1016/0001-6160(89)90039-4 ↗
33. D.J. Lloyd, H. Lagace, A. McLeod, and P.L. Morris: Mater. Sci. Eng. A, 1989, vol. 107, pp. 73–80.10.1016/0921-5093(89)90376-6 ↗
34. T.J.A. Doel and P. Bowen: Compos. Part A, 1996, vol. 27, pp. 655–65.10.1016/1359-835X(96)00040-1 ↗
35. D.J. Lloyd: Acta Metall. Mater., 1991, vol. 39, pp. 59–71.10.1016/0956-7151(91)90328-X ↗