journal article·2003-01

Demonstration of an endurance limit in cast 319 aluminum

M. J. Caton, J. W. Jones, H. Mayer, S. Stanzl-Tschegg, J. E. Allison

Publisher page

Abstract

An investigation of the fatigue properties of cast W319-T7, an Al-Si-Cu alloy used in automotive engine components, was conducted using ultrasonic testing equipment with operating frequencies of 20 kHz. The stress-life (S-N) behavior at room temperature was determined for three solidification conditions of this alloy, where stresses for fatigue lives ranging from 105 to 109 cycles were determined. The results are compared to fatigue data acquired using servohydraulic equipment operating at 40 Hz. No influence of loading frequency has been observed. A discrete endurance limit is indicated for each of the three solidification conditions of W319-T7. The scientific and practical implications of this result are discussed. A material model presented previously is modified by introducing a crack growth threshold condition in order to predict the observed endurance limits. The model is shown to effectively predict the influence of solidification time on the fatigue properties of W319-T7.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Fatigue and fracture mechanics · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. M.J. Caton, J.W. Jones, and J.E. Allison: in Fatigue Crack Growth Thresholds, Endurance Limits, and Design, ASTM STP 1372, J.C. Newman and R.S. Piascik, eds., ASTM, West Conshohocken, PA, 2000, pp. 285–303.10.1520/STP13439S ↗
2. J.M. Boileau, P.C. Collins, and J.E. Allison: Proc. 5th Int. Conf. on Molten Metal Processing, AFS Inc., Des Plains, IL, 1998.
3. J.G. Conley, B. Moran, and J. Gray: Proc. SAE Int. Congr. Exp., SAE SP-1350, SAE International, Warrendale, PA, 1998, pp. 25–38.
4. K.B. Lease and R.I. Stephens: Fatigue Research and Applications, SAE SP-1009, SAE International, Warrendale, PA, 1993, pp. 11–29.
5. B. Skallerud, T. Iveland, and G. Harkegard: Eng. Fract. Mech., 1993, vol. 44 (6), pp. 857–74.10.1016/0013-7944(93)90108-5 ↗
6. C. Ting: Ph.D. Thesis, University of Illinois at Urbana-Champaign, Urbana, IL, 1991.
7. M.J. Couper, A.E. Neeson, and J.R. Griffiths: Fatigue Fract. Eng. Mater. Struct., 1990, vol. 13 (3), pp. 213–27.10.1111/j.1460-2695.1990.tb00594.x ↗
8. S.E. Stanzl-Tschegg, H.R. Mayer, E.K. Tschegg, and A. Beste: Int. J. Fatigue, 1993, vol. 15 (4), pp. 311–16.10.1016/0142-1123(93)90380-9 ↗
9. H.R. Mayer, H. Lipowsky, M. Papakyriacou, R. Rosch, A. Stich, and S. Stanzl-Tschegg: Fatigue Fract. Eng. Mater. Struct., 2000, vol. 22.10.1046/j.1460-2695.1999.00205.x ↗
10. M.J. Caton, J.W. Jones, and J.E. Allison: in Small Fatigue Cracks: Mechanics, Mechanisms and Applications, K.S. Ravichandran, R.O. Ritchie, and Y. Murakami, eds., Elsevier Science Ltd., Oxford, United Kingdom, 1999, pp. 155–66.
11. H. Mayer: Int. Mater. Rev., 1999, vol. 44 (1), pp. 1–34.10.1179/imr.1999.44.1.1 ↗
12. J.M. Boileau: Ph.D. Thesis, Wayne State University, Detroit, MI, 1999.
13. M.J. Caton: Ph.D. Thesis, University of Michigan, Ann Arbor, MI, 2001.
14. S. Suresh: Fatigue of Materials, Cambridge University Press, Cambridge, United Kingdom, 1991.
15. S.E. Stanzl-Tschegg, H.R. Mayer, A. Beste, and S. Kroll: Int. J. Fatigue, 1995, vol. 17 (2), pp. 149–56.10.1016/0142-1123(95)95895-N ↗
16. H.R. Mayer and S. Stanzl-Tschegg: in Fatigue ’96, G. Lutjering and H. Nowack, eds., Elsevier, Oxford, United Kingdom, 1996, vol. 1, pp. 691–96.
17. M. Papakyriacou, H.R. Mayer, S. Stanzl-Tschegg, and M. Groschl: Int. J. Fatigue, 1996, vol. 18 (7), pp. 475–81.10.1016/0142-1123(96)00090-4 ↗
18. H.R. Mayer, M. Papakyriacou, R. Pippan, and S. Stanzl-Tschegg: Mater. Sci. Eng. A, 2001, vol. A314 (1–2), pp. 48–54.10.1016/S0921-5093(00)01913-4 ↗
19. M.J. Caton, J.W. Jones, J.M. Boileau, and J.E. Allison: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3055–68.10.1007/s11661-999-0216-4 ↗
20. J.E. Allison, J.W. Jones, M.J. Caton, and J.M. Boileau: in Fatigue ’99, X.R. Wu and Z.G. Wang, eds., Higher Education Press, Beijing, 1999, pp. 2021–28.
21. K. Donald: Mechanics Fatigue Crack Closure, ASTM, Philadelphia, PA, 1988, pp. 222–29.10.1520/STP27211S ↗