Microstructures of hot-rolled high-strength steels with significant differences in edge formability
Source abstract
Abstract
The relationship between microstructure and hole expansion was investigated for three industrial mill-processed steels with similar yield strength (about 525 MPa) and total elongation (about 25 pct). The nominal steel composition was (in mass pct) 0.1C, 1.4Mn, 0.1Si, 0.02Al, 0.04Nb, and 0.02Ti; any variations in composition or processing history were unintentional. The microstructures of all steels consisted of about 80 pct of proeutectoid ferrite and 20 pct of a carbon-enriched, high-hardness, low-temperature transformation product (LTTP). Despite these similarities, the hole-expansion values for the steels were 44, 74, and 115 pct. Detailed microstructural characterization revealed significant differences in the LTTPs of the three steels, as well as several important differences in the proeutectoid ferrite grains. Previously reported negative effects of large quantities of martensite, microstructural banding, and a high hardness ratio (LTTP/ferrite) were validated. Different hardness ratios correlated with differences in (1) dislocation substructures of proeutectoid ferrite grains (2) grain-size distribution, and (3) the fine structure of bainitelike/pearlitelike regions. Superior hole-expansion performance (or edge formability) was associated with a microstructure consisting of 78 pct of uniformly fine-grained proeutectoid ferrite and 22 pct of a bainitelike microconstituent, a minimum amount of microstructural banding, and a low hardness ratio. Tensile-bar fracture surfaces of a material with this microstructure showed the largest amount of microplasticity.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Magnetic Properties and Applications · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. R.R. Hilson, T.E. Fine, and G.J. Hansen:Microalloying '75, Union Carbide, New York, NY, 1977, pp. 654–64.
2. H. Takechi: inHot-& Cold-Rolled Sheet Steels, R. Pradhan and G. Ludkovsky, eds., TMS-AIME, Warrendale, PA, 1988, pp. 117–38.
3. T. Maksuoka, T. Kawai, Y. Hobo, and S. Ueda:Trans. Iron Steel Inst. Jpn., 1975, vol. 15, pp. 137–44.10.2355/isijinternational1966.15.137 ↗
4. Y.J. Park, A.P. Coldren, and J.W. Morrow: inFundamentals of Dual-Phase Steels, R.A. Kot and B.L. Bramfitt, eds. TMS-AIME, Warren-dale, PA, 1981, pp. 485–97.
5. M. Sudo, S. Hashimoto, and S. Kambe:Trans. Iron Steel Inst. Jpn., 1983, vol. 23, p. 303.10.2355/isijinternational1966.23.303 ↗
6. N. Nagao, K. Kunishigie, S. Hamamatsu, and T. Nunokawa: inAccelerated Cooling of Steel, P. Southwick, ed., TMS-AIME, Warrendale, PA, 1985, p. 463.
7. S. Hashimoto, M. Sudo, K. Mimura, and T. Hosada:Trans. Iron Steel Inst. Jpn., 1986, vol. 26, p. 985.10.2355/isijinternational1966.26.985 ↗
8. M. Mizui and M. Takahashi:Iron Steelmaker, 1992, vol. 19 (9), pp. 31–38.
9. H. Kimura, T. Ogura, M. Kinoshita, T. Okita, and K. Osawa: SAE Technical Paper No. 930283, SAE, Warrendale, PA, 1993.
10. I. Machida, M. Narita, R. Kurera, N. Aoyagi, and M. Sano: SAE Technical Paper No. 940536, SAE, Warrendale, PA, 1994.
11. S. Toyoda, T. Urabe, K. Osawa, and M. Ohmura. Technical Report No. 58, NKK Corporation, 1997.
12. A. Schmitz, J. Neutjens, J.C. Herman, and V. Leroy:40th MWSP Conf Proc., ISS, Warrendale, PA, 1998, vol. XXXVI, pp. 295–309.
13. J. Neutjens, P. Harlet, T. Bakolas, and P. Cantinieaux:40th MWSP Conf Proc., ISS, Warrendale, PA, 1998, vol. XXXVI, pp. 311–21.
14. Metals Handbook,, 10th ed., ASM, Materials Park, OH, 1990, vol. 1, pp. 573–90.
15. A. Nishimoto, Y. Hosoya, and K. Nakaoka: inFundamentals of Dual-Phase Steels, R.A. Kot and B.L. Bramfitt, eds., TMS-AIME, Warrendale, PA, 1981, pp. 447–63.
16. R.D. Adamczyk, D.W. Dickson, and R.P. Krupitzer: SAE Technical Paper No. 830237, SAE, Warrendale, PA, 1983.
17. R.D. Adamczyk and D.W. Dickson:J. Appl. Metalworking, 1986, vol. 4, p. 157.10.1007/BF02834379 ↗
18. H. Asano, N. Matsuzu, A. Itami, and K. Koyama: SAE Technical Paper No. 940943, SAE, Warrendale, PA, 1994.
19. M. Sudo and I. Koubo:Scand. J. Metall. 1984, vol. 13, p. 329.
20. Y. Ito, K. Hashigichi, and N. Ohashi:Proc. ICSTIS, 1971, Sect. 6, p. 958.
21. A.J. Klein and E.W. Hitchler:Met. Eng. Q., 1973, Aug., p. 157.
22. M. Sudo and T. Iwai:Trans. Iron Steel Inst. Jpn. 1983, vol. 23, pp. 294–302.10.2355/isijinternational1966.23.294 ↗
23. 1989 Annual Book of ASTM Standards, ASTM Designation E 8, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 131–46.
24. 1989 Annual Book of ASTM Standards, ASTM Designations E 112 and E 562, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 284–309. and pp. 582–86, respectively.
25. 1989 Annual Book of ASTM Standards, ASTM Designation E 112, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 284–309.
26. B.D. Cullity:Elements of X-ray Diffraction, 2nd ed., Addison-Wesley, Reading, MA, 1978, p. 412.
27. 1989 Annual Book of ASTM Standards, ASTM Designations A 370, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 3–48.
28. T. Parayil and G. Ludkovsky:Proc. Int. Symp. on Accelerated Cooling of Rolled Steels, G.E. Ruddle and A.F. Crawley, ed., Pergamon Press, New York, NY, 1988, pp. 131–44.
29. P. Messien, J.-C. Herman, and T. Gréday: inFundamentals of Dual-Phase Steels, R.A. Kot and B.L. Bramfitt, eds., TMS-AIME, Warrendale, PA, 1981, pp. 161–80.
30. G.R. Speich and R.L. Miller:Proc. Int. Conf. Solid→Solid Phase Transformations, H.I. Aaronson, D.E. Laughlin, R.F. Sekerka, and C.M. Wayman, eds., TMS-AIME, Warrendale, PA, 1982, pp. 843–48.
31. J.S. Kirkaldy, J. von Destinon-Forstmann, and R.J. Brigham:Can. Metall. Q., 1962, vol. 1, pp. 59–81.10.1179/cmq.1962.1.1.59 ↗
32. L.J. Habraken and M. EconomopoulosTransformation and Hardenability in Steels, Climax Molybdenum Co., Ann Arbor, MI, 1967, pp. 69–107.
33. A.R. Marder and G. Krauss:Trans. ASM, 1967, vol. 60, pp. 651–60.
34. E. Scheil:Z. Metalkd., 1942, vol. 34, p. 70.
35. R.M. Fisher, G.R. Speich, L.J. Cuddy, and Hsum Hu: inPhysical Chemistry in Metallurgy, R.M. Fisher, R.A. Oriani, and E.T. Turkodogan eds., U.S. Steel, Monroeville, PA, 1976, pp. 463–88.
36. S.W. Thompson and P.R. Howell:Mater. Sci. Technol., 1992, vol. 8, pp. 777–84.10.1179/mst.1992.8.9.777 ↗
37. K.W. Andrews:J. Iron Steel Inst., 1965, vol. 203, pp. 721–27.
38. C. Wells and R.F. Mehl:Trans. AIME, 1940, vol. 140, pp. 279–306.
39. C.A. Muojekwu, D.Q. Jin, V.H. Hernandez, I.V. Samarasekera, and J.K. Brimacombe:38th MWSP Conf Proc., ISS, Warrendale, PA, 1997, vol. XXXIV, pp. 351–66.
40. C.A. Muojekwu, D.Q. Jin, V.H. Hermandez, I.V. Samarasekera, and J.K. Brimacombe:39th MWSP Conf Proc., ISS, Warrendale, PA, 1998, vol. XXXV, p. 219.
41. L. Brewer, J. Chipman, and S.-G. Chang:Metals Handbook, 8th ed. ASM, Metals Park, OH, 1973, vol. 8, pp. 407–08.
42. J.M. Moyer and G.S. Ansell:Metall. Trans. A, 1975, vol. 6A, pp. 175–91.
43. G.R. Speich: inFundamentals of Dual-Phase Steels, R.A. Kot and B.L. Bramfitt, eds., TMS-AIME, Warrendale, PA, 1981, pp. 3–45.
44. I. Tamura, C. Ouchi, T. Tanaka, and H. Sekine:Thermomechanical Processing of High Strength Low Alloy Steels, Butterworth & Co. (Publishers) Ltd., Boston, MA, 1988, p. 142.
45. C. Ouchi, T. Sampei, and I. Kozasu:Trans. Iron Steel Inst. Jpn., 1982, vol. 22, p. 214.10.2355/isijinternational1966.22.214 ↗
46. S. Modin:Jernkont. Ann., 1958, vol. 142, pp. 37–80.
47. D. Cheetham and N. Ridley:Met. Sci., 1975, vol. 9, pp. 411–14.10.1016/0036-9748(75)90173-8 ↗
48. M.S. Rashid: inFormable HSLA and Dual-Phase Steels, A.T. Davenport, ed., TMS-AIME, Warrendale, PA, 1979, pp. 3–24.
49. J.M. Rigsbee, J.K. Abraham, A.T. Davenport, J.E. Franklin, and J.W. Pickens: inStructure and Properties of Dual-Phase Steels, R.A. Kot and J.W. Morris, eds., TMS-AIME, Warrendale, PA, 1979, pp. 304–29.
50. G. Krauss: inHardenability Concepts with Applications to Steel, D.V. Doane and J.S. Kirkaldy, eds., TMS-AIME, Warrendale, PA, 1978, pp. 229–45.
51. R. Stevenson: inFormable HSLA and Dual-Phase, Steels, A.T. Davenport, ed., TMS-AIME, Warrendale, PA, 1979, pp. 99–108.