journal article·2000-08

Effects of microstructure on the short fatigue crack initiation and propagation characteristics of biomedical α/β titanium alloys

Toshikazu Akahori, Mitsuo Niinomi, Kei-Ichi Fukunaga, Ikuhiro Inagaki

Publisher page

Abstract

This article presents the results of a study of the effects of microstructure on the fatigue strength and the short fatigue crack initiation and propagation characteristics of a biomedical α/β titanium alloy, Ti-6Al-7Nb. The results are compared to those obtained from a Ti-6Al-4V extra-low interstitial (ELI) alloy. Fatigue crack initiation occurs mainly at primary α grain boundaries in an equiaxed α structure, whereas, in a Widmanstatten α structure, initiation occurs within the α colonies and prior β grains, where α plates are inclined at around 45 deg to the stress-axis direction. In an equiaxed α structure, the short fatigue crack initiation and propagation life, where the length of the crack (a) is in a microstructurally short fatigue-crack regime (2a < 50 µm), occupies around 50 pct of the total fatigue life. On the other hand, the fatigue crack in a Widmanstatten α structure initiates at very early stages of fatigue, and, therefore, the fatigue crack-initiation life occupies a few percentages of the total fatigue life in an α structure. Then, the short fatigue crack propagates rapidly and is arrested at the grain boundaries of α colonies or prior β grains for a relatively long period, until the short crack passes through the boundaries to specimen failure. Therefore, the short fatigue crack-arrest life occupies more than 90 pct of the total fatigue life in a Widmanstatten α structure. These trends are similar between the Ti-6Al-7Nb and Ti-6Al-4V ELI alloys and biomedical α/β titanium alloys. The total fatigue life for the Ti-6Al-7Nb alloy with an equiaxed α structure is changed by the volume fraction of primary α phase and the cooling rate after solution treatment. By increasing the volume fraction of the primary α phase from 0 to 70 pct, the fatigue limit of the Ti-6Al-7Nb alloy is raised. Changing the cooling rate after solution treatment by switching from air cooling to water quenching improves the fatigue limit of the Ti-6Al-7Nb alloy significantly.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Mechanical Failure Analysis and Simulation · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. S.A. Brown and J.E. Lemons: Medical Applications of Titanium and Its Alloys, ASTM STP 1272, ASTM, Philadelphia, PA, 1996, pp. ix-xii.
2. R. Boyer, G. Welsch, and E.W. Collings: Materials Handbook: Titanium Alloys, ASM, Materials Park, OH, 1994, pp. 483–636.
3. Standard Specification for Wrought Titanium 6Al 4V ELI Alloy for Surgical Implants, ASTM Designation F136-82, ASTM, Philadelphia, PA, 1994, pp. 19–20.
4. Y. Okazaki: J. Jpn. Inst. Met., 1997, vol. 36, pp. 966–68.
5. Standard Specification for Wrought Titanium 6Al 7Nb Alloy for Surgical Implants, ASTM Designation F1295-92, ASTM, Philadelphia, PA, 1994, pp. 687–89.
6. R.R. Boyer, D. Eylon, and G. Lütjering: Fatigue Behavior of Titanium Alloys, TMS, Warrendale, PA, 1998.
7. G. Lütjering and A. Gysler: in Titanium Science and Technology, G. Lutering, U. Zwicker, and W. Bunk, eds., Deutsche Gesellschaft für Metallkunde, Oberursel, 1985, vol. 4, pp. 2065–84.
8. D. Eylon and P.J. Bania: Metall. Trans. A, 1978, vol. 9A, pp. 1273–79.10.1007/BF02652251 ↗
9. G. Lütjering, A. Gysler, and L. Wagner: Proc. 6th World Conf. on Titanium, les éditions de physique, CANNES, 1988, pp. 71–80.
10. G.R. Yoder, L.A. Cooley, and T.W. Crooker: Trans. ASME, 1979, vol. 101, pp. 86–90.
11. H. Pushnik, J. Fladischer, G. Lütjering, and R.I. Jaffee: Proc. Titanium ’92, F.H. Froes and I.L. Caplan, eds., TMS, Warrendale, PA, 1992, vol. 1, pp. 131–40.
12. L. Wagner and G. Lütjering: Z. Metallkd., 1987, vol. 78, pp. 369–75.
13. C.C. Wojcik, K.S. Chan, and D.A. Koss: Acta Metall., 1988, vol. 36, pp. 1261–39.10.1016/0001-6160(88)90278-7 ↗
14. D.K. Benson, J.C. Grosskreutz, and G.G. Shaw: Metall. Trans., 1972, vol. 3, pp. 1239–48.10.1007/BF02642458 ↗
15. J.L. Gilbert and H.R. Piehler: Metall. Mater. Trans. A, 1993, vol. 24A, pp. 669–80.10.1007/BF02656635 ↗
16. I.J. Polmear: in Light Alloys, R.W.K. Honeycombe and P. Hancock, eds., Edward Arnold, London, 1989, pp. 258–60.
17. R. Brown and G.C. Smith: Scripta Metall., 1981, vol. 15, pp. 357–60.10.1016/0036-9748(81)90209-X ↗
18. M. Okazaki and T. Hizumi: J. Soc. Mater. Sci., 1994, vol. 43, pp. 1238–44.10.2472/jsms.43.1238 ↗
19. M. Niinomi, T. Kobayashi, O. Teriyama, N. Kwakami, Y. Ishida, and Y. Matuyma: Metall. Mater. Trans. A, 1996, vol. 27, pp. 3925–35.10.1007/BF02595641 ↗
20. M.H. Swain: in Small-Crack Test Method, J.M. Larsen and J.E. Allison, eds., ASTM, Philadelphia, PA, 1992, pp. 34–56.10.1520/STP15063S ↗
21. Division of Fatigue and Microstructure Committee of Fatigue: Microstructure, Mechanical Properties and Fatigue Strength of (α + β) Titanium Alloys, The Society of Materials Science Japan, Kyoto, Japan, 1994, pp. 47–64.
22. J.J. Lucas and P.P. Konieczny: Metall. Trans., 1971, vol. 3, pp. 911–12.10.1007/BF02662756 ↗
23. K. Minakawa: J. Iron Steel Inst. Jpn., 1989, vol. 75, pp. 36–43.10.2355/tetsutohagane1955.75.7_1104 ↗
24. M. Okazaki, T. Suganuma, Y. Mutoh, and K. Minakawa: J. Jpn. Light Met., 1992, vol. 42, pp. 627–32.10.2464/jilm.42.627 ↗
25. Y. Ito, Y. Moriguchi, and T. Nishimura: J. Iron Steel Inst. Jpn., 1986, vol. 72, pp. 625–32.10.2355/tetsutohagane1955.72.6_625 ↗
26. M. Niinomi and T. Kobayashi: Mater. Sci. Eng. A, 1996, vol. 213, pp. 16–24.10.1016/0921-5093(96)10239-2 ↗
27. J.C. Williams and M.J. Blackburn: Phase Trans. Ti Alloys, 1967, vol. 60, pp. 373–83.