Evaluation of the Role of Deformation Twinning in Work Hardening Behavior of Face-Centered-Cubic Polycrystals
Source abstract
Abstract
Results of an investigation on the evolution of microstructure during simple compression testing of two face-centered-cubic (fcc) polycrystals, IN625 superalloy and 316L stainless steel, are reported and a review on the existing data related to the uniaxial deformation of fcc polycrystals is presented. It is found that while a number of fcc polycrystals show linear hardening behavior, the evolution of the underlying microstructure may be quite different. It is argued that, in contrast to the current belief, deformation twinning may not be the sole cause of linear hardening in low stacking fault energy (SFE) fcc polycrystals. It is suggested that, due to the requirement of slip system change prior to twinning, only fcc crystals with sufficiently low twinning stress are expected to form mechanical twins after a certain amount of initial plastic strain. In other fcc polycrystals that show linear hardening behavior competitive mechanisms, such as formation of Lomer–Cottrell (LC) locks may be dominant hardening mechanism. The effectiveness of these slip barriers in fcc polycrystals is expected to increase with the tendency of the material to slip planarity. Therefore, parameters such as SFE, temperature, Peierls stress, and short range ordering (SRO) are expected to have a contribution to the linear hardening response of fcc polycrystals. This proposal appears to offer a more comprehensive explanation for a wide range of experimental data presented in the scientific literature.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. S. Asgari, E. El-Danaf, S.R. Kalidindi, R.D. Doherty: Metall. Mater. Trans. A, 1997, vol. 28A, p. 178110.1007/s11661-997-0109-3 ↗
2. S. Mahajan, G.Y. Chin: Acta Metall., 1973, vol. 21, p. 17310.1016/0001-6160(73)90059-X ↗
3. L. Remy: Acta Metall., 1977, vol. 25, p. 71110.1016/0001-6160(77)90013-X ↗
4. L. Remy: Metall. Trans. A, 1981, vol. 12A, p. 38710.1007/BF02648536 ↗
5. L. Remy: Acta Metall., 1978, vol. 26, p. 44310.1016/0001-6160(78)90170-0 ↗
6. J.W. Christian, S. Mahajan: Prog. Mater. Sci., 1995, vol. 39, p. 110.1016/0079-6425(94)00007-7 ↗
7. E.K. Cerreta, G.T Gray III: Metall. Mater. Trans. A, 2004, vol. 35A, p. 199910.1007/s11661-004-0149-x ↗
8. C.A. Yablinsky, E.K. Cerreta, G.T. Gray III, D.W. Brown, S.C. Vogel: Metall. Mater. Trans. A, 2006, vol. 37A, p. 190710.1007/s11661-006-0133-8 ↗
9. E. El-Danaf, S.R. Kalidindi, R.D. Doherty: Metall. Mater. Trans. A, 1999, vol. 30A, p. 1223.10.1007/s11661-999-0272-9 ↗
10. A. Rohatgi, K.S. Vecchio, G.T. Gray III: Metall. Mater. Trans. A, 2001, vol. 32A, p. 13510.1007/s11661-001-0109-7 ↗
11. E. El-Danaf, S.R. Kalidindi, R.D. Doherty: Int. J. Plast., 2001, vol. 17, p. 124510.1016/S0749-6419(00)00090-5 ↗
12. S. Asgari: J. Mater. Process. Technol., 2004, vols. 155–156, p. 190510.1016/j.jmatprotec.2004.04.280 ↗
13. S.R. Kalidindi: Int. J. Plast., 1998, vol. 14, p. 126510.1016/S0749-6419(98)00054-0 ↗
14. S.R. Kalidindi: Int. J. Plast., 2001, vol. 17, p. 83710.1016/S0749-6419(00)00071-1 ↗
15. J.A. Venables: in Deformation Twinning, R.D. Reed-Hill, J.P. Hirth, and H.C. Rogers, eds., Gordon and Breach, 1964, p. 77
16. P. Haasen: in Physical Metallurgy, R.W. Cahn and P. Haasen, eds., North-Holland, 1996, p. 200910.1016/B978-044489875-3/50028-4 ↗
17. U.F. Kocks, H. Mecking: Prog. Mater. Sci., 2003, vol. 48, p. 17110.1016/S0079-6425(02)00003-8 ↗
18. K. Sangwal: in Defects in Solids, S. Amlinekx and J. Nihoul, eds., North-Holland, 1987, vol. 15, p. 1
19. J.P. Hirth, J. Loth: Theory of Dislocations, McGraw-Hill, New York, NY, 1968, p. 292
20. V. Gerold, H.P. Karnthaler: Acta Metall., 1989, vol. 37, p. 217710.1016/0001-6160(89)90143-0 ↗
21. S.I. Hong, C. Laird: Acta Metall., 1990, vol. 38, p. 158110.1016/0956-7151(90)90126-2 ↗
22. R. Swalin: Thermodynamics of Solids, John Wiley and Sons, 1962, p. 11310.1149/1.2425309 ↗
23. I. Ansara, M. Selleby: CALPHAD, 1994, vol. 18, p. 9910.1016/0364-5916(94)90011-6 ↗
24. Z. Kejun, Z. Xianzhang, J. Zhanpeng: J. Alloys Compd., 1992, vol. 179, p. 17710.1016/0925-8388(92)90217-W ↗
25. B.J. Lee: CALPHAD, 1992, vol. 16, p. 12110.1016/0364-5916(92)90002-F ↗
26. N. Clement, D. Caillard, J.L. Martin: Acta Metall., 1984, vol. 32, p. 96110.1016/0001-6160(84)90034-8 ↗
27. C.J. Vander Wekken, R. Taggart, D.H. Polonis: Met. Sci. J., 1971, vol. 5, p. 21910.1179/030634571790439487 ↗
28. V.M. Silonov, S. Hamami: Phys. Met. Metall., 1990, vol. 69, p. 122
29. I. Karaman, H. Sehitoglu, H.J. Maier, Y.I. Chumlyakov: Acta Mater., 2001, vol. 49, p. 391910.1016/S1359-6454(01)00296-8 ↗
30. H.E. Lee, T.S. Byun, J.D. Hunn, M.H. Yoo, K. Farrell, L.K. Mansur: Acta Mater., 2001, vol. 49, p. 326910.1016/S1359-6454(01)00193-8 ↗
31. H.E. Lee, T.S. Byun, J.D. Hunn, M.H. Yoo, K. Farrell, L.K. Mansur: Acta Mater., 2001, vol. 49, p. 327710.1016/S1359-6454(01)00194-X ↗
32. P. Mullner, A.E. Romanov: Acta Mater., 2000, vol. 48, p. 232310.1016/S1359-6454(00)00025-2 ↗
33. P. Mullner, C. Solenthaler, M.O. Speidel: Acta Mater., 1994, vol. 42, p. 172710.1016/0956-7151(94)90382-4 ↗
34. P. Mullner, C. Solenthaler, M.O. Speidel: in Twinning in Advanced Materials, M.H. Yoo, M. Wuttig, eds., TMS, Warrendale, PA, 1994, p. 483
35. J. Koutsky, Z. Novy: J. Mater. Process. Technol., 2001, vol. 109, p. 12010.1016/S0924-0136(00)00785-8 ↗
36. R.W.K. Honeycombe: Plastic Deformation of Metals, Edward Arnold, 1984, p. 81
37. J.G. Sevillano: in Materials Science and Technology: A Comprehensive Treatment, VCH, New York, NY, 1993, vol. 6, p. 19
38. A.S. Argon: in Physical Metallurgy, R.W. Cahn and P. Haasen, eds., North-Holland, 1996. p. 187710.1016/B978-044489875-3/50026-0 ↗
39. G.J. Taylor: J. Inst. Metals, 1938, vol. 62, p. 307
40. J.D. Embury, M.S. Szczerba, Z.S. Basinsky: in Twinning in Advanced Materials, M.H. Yoo, M. Wuttig, eds., TMS, Warrendale, PA, 1994, p. 331
41. P. Feltham, J.D. Meakin: Phil. Mag., 1957, vol. 2, p. 10510.1080/14786435708231728 ↗
42. B. Jaoul: J. Mech. Phys. Solids, 1957, vol. 5, p. 9510.1016/0022-5096(57)90054-6 ↗
43. M.M. Hutchinson, R.W.K. Honeycombe: Met. Sci. J., 1967, vol. 1, p. 7010.1179/msc.1967.1.1.70 ↗
44. U.F. Kocks: Acta Metall., 1958, vol. 6, p. 8510.1016/0001-6160(58)90117-2 ↗
45. H. Mecking, U.F. Kocks: Acta Metall., 1981, vol. 29, p. 186510.1016/0001-6160(81)90112-7 ↗