journal article·2011-07

Mechanical Behaviors of Ultrafine-Grained 301 Austenitic Stainless Steel Produced by Equal-Channel Angular Pressing

C. X. Huang, G. Yang, C. Wang, Z. F. Zhang, S. D. Wu

Publisher page

Abstract

The technique of equal-channel angular pressing (ECAP) was used to refine the microstructure of an AISI 301 austenitic stainless steel (SS). An ultrafine-grained (UFG) microstructure consisting mainly of austenite and a few martensite was achieved in 301 steel after ECAP processing for four passes at 523 K (250 °C). By submitting the as-ECAP rods to annealing treatment in the temperature range from 853 K to 893 K (580 °C to 620 °C) for 60 minutes, fully austenitic microstructures with grain sizes of 210 to 310 nm were obtained. The uniaxial tensile tests indicated that UFG 301 austenitic SS had an excellent combination of high yield strength (>1.0 GPa) and high elongation-to-fracture (>30 pct). The tensile stress–strain curves exhibited distinct yielding peak followed by obvious Luders deformation. Measurements showed that Luders elongation increased with an increase in strength as well as a decrease in grain size. The microstructural changes in ultrafine austenite grains during tensile deformation were tracked by X-ray diffraction and transmission electron microscope. It was found that the strain-induced phase transformation from austenite to martensite took place soon after plastic deformation. The transformation rate with strain and the maximum strain-induced martensite were promoted significantly by ultrafine austenite grains. The enhanced martensitic transformation provided extra strain-hardening ability to sustain the propagation of Luders bands and large uniform plastic deformation. During tensile deformation, the Luders bands and martensitic transformation interacted with each other and made great contribution to the excellent mechanical properties in UFG austenitic SS.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. C.C. Koch, D.G. Morris, K. Lu, and A. Inoue: MRS Bull., 1999, vol. 54, pp. 54-58.10.1557/S0883769400051551 ↗
2. R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov: Prog. Mater. Sci., 2000, vol. 45, pp. 103-89.10.1016/S0079-6425(99)00007-9 ↗
3. H. Gleiter: Acta Mater., 2000, vol. 48, pp. 1-29.10.1016/S1359-6454(99)00285-2 ↗
4. M. Dao, L. Lu, R.L. Asaro, J.T.M. Hosson, and E. Ma: Acta Mater., 2007, vol. 55, pp. 4041-65.10.1016/j.actamat.2007.01.038 ↗
5. M.A. Meyers, A. Mishra, and D.J. Benson: Prog. Mater. Sci., 2006, vol. 51, pp. 427-556.10.1016/j.pmatsci.2005.08.003 ↗
6. Y.M. Wang, E. Ma, and M.W. Chen: Appl. Phys. Lett., 2002, vol. 80, pp. 2395-97.10.1063/1.1465528 ↗
7. D. Jia, Y.M. Wang, K.T. Remesh, E. Ma, Y.T. Zhu, and R.Z. Valiev: Appl. Phys. Lett., 2001, vol. 79, pp. 611-13.10.1063/1.1384000 ↗
8. E. Ma: Scripta Mater., 2003, vol. 49, pp. 663-68.10.1016/S1359-6462(03)00396-8 ↗
9. C.X. Huang, S.D. Wu, S.X. Li, and Z.F. Zhang: Adv. Eng. Mater., 2008, vol. 10, pp. 434-38.10.1002/adem.200700324 ↗
10. S. Qu, X.H. An, H.J. Yang, C.X. Huang, G. Yang, Q.S Zang, Z.G. Wang, S.D. Wu, and Z.F. Zhang: Acta Mater., 2009, vol. 57, pp. 1586-601.10.1016/j.actamat.2008.12.002 ↗
11. Y.M. Wang, M.W. Chen, F.H. Zhou, and E. Ma: Nature, 2002, vol. 419, pp. 912-15.10.1038/nature01133 ↗
12. Z. Horita, K. Oh-ishi, T. Fujita, K. Kaneko, and T.G. Langdon: Adv. Mater., 2005, vol. 17, pp. 1599-602.10.1002/adma.200500069 ↗
13. Y. Ma, J.E. Jin, and Y.K. Lee: Scripta Mater., 2005, vol. 52, pp. 1311-15.10.1016/j.scriptamat.2005.02.018 ↗
14. B.Q. Han, E.J. Lavernia, and F.A. Mohamed: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 71-83.10.1007/s11661-003-0209-7 ↗
15. J.E. Carsley, A. Fisher, W.W. Milligan, and E.C. Aifantis: Metall. Mater. Trans. A, 1998, vol. 27A, pp. 2261-71.10.1007/s11661-998-0104-3 ↗
16. C.Y. Yu, P.L. Sun, P.W. Kao, and C.P. Chang: Scripta Mater., 2005, vol. 52, pp. 359-63.10.1016/j.scriptamat.2004.10.035 ↗
17. I. Sabirov, Y. Estrin, M.R. Barnett, I. Timokhina, and P.D. Hodgson: Acta Mater., 2008, vol. 56, pp. 2223-30.10.1016/j.actamat.2008.01.020 ↗
18. K. Tomimura, H. Nagamori, S. Takaki, and Y. Tokunaga: J. Jpn. Inst. Met., 1991, vol. 56, pp. 376-82.10.2320/jinstmet1952.55.4_376 ↗
19. N. Tsuji, Y. Ito, Y. Saito, and Y. Minamino: Scripta Mater., 2002, vol. 47, pp. 893-99.10.1016/S1359-6462(02)00282-8 ↗
20. C.Y. Yu, P.W. Kao, and C.P. Chang: Acta Mater., 2005, vol. 53, pp. 4019-28.10.1016/j.actamat.2005.05.005 ↗
21. K. Spencer, J.D. Embury, K.T. Conlon, M. Veron, and Y. Brechet: Mater. Sci. Eng. A, 2004, vols. 387-9A, pp. 873-81.10.1016/j.msea.2003.11.084 ↗
22. K.X. Tao, H. Choo, H.Q. Li, B. Clausen, J.E. Jin, and Y.K. Lee: Appl. Phys. Lett., 2007, vol. 90, p. 101911.10.1063/1.2711758 ↗
23. C.S. Yoo, Y.M. Park, Y.S. Jung, and Y.K. Lee: Scripta Mater., 2008, vol. 59, pp. 71-44.10.1016/j.scriptamat.2008.02.024 ↗
24. A. Di Schino, M. Barteri, and L.M. Kenny: J. Mater. Sci., 2002, vol. 37, pp. 4561-65.10.1023/A:1020631912685 ↗
25. A. Di Schino, M. Barteri, and L.M. Kenny: J. Mater. Sci. Lett., 2002, vol. 21, pp. 751-53.10.1023/A:1015757710546 ↗
26. S. Rajasekhara, P.J. Ferreira, L.P. Karjalainen, and A. Kyröläinen: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1202-10.10.1007/s11661-007-9143-4 ↗
27. M.C. Somani, P. Juntunen, S. Rajasekhara, R.D.K. Misra, and A. Kyröläinen: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 729-44.10.1007/s11661-008-9723-y ↗
28. S.K. Varma, J. Kalyanam, L.E. Murr, and V. Srinivas: J. Mater. Sci. Lett., 1994, vol. 13, pp. 107-11.10.1007/BF00416816 ↗
29. T. Iwamoto and T. Tsuta: Int. J. Plast., 2000, vol. 16, pp. 791-804.10.1016/S0749-6419(99)00079-0 ↗
30. R.Z. Valiev and T.G. Langdon: Prog. Mater. Sci., 2006, vol. 51, pp. 881-981.10.1016/j.pmatsci.2006.02.003 ↗
31. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill Book, New York, 1986, p. 293.
32. R.L. Miller: Trans. TMS-ASM, 1968, vol. 61, pp. 592-97.
33. C.X. Huang, G. Yang, B. Deng, S.D. Wu, S.X. Li, and Z.F. Zhang: Phil. Mag., 2007, vol. 87, pp. 4949-71.10.1080/14786430701594046 ↗
34. L. Balogh, T. Ungar, Y.H. Zhao, Y.T. Zhu, Z. Horita, C. Xu, and T.G. Langdon: Acta Mater., 2008, vol. 56, pp. 809-20.10.1016/j.actamat.2007.10.053 ↗
35. R.E. Schramm and R.P. Reed: Metall. Trans. A, 1975, vol. 6A, pp. 1345-51.10.1007/BF02641927 ↗
36. K. Edalati, T. Fujioka, and Z. Horita: Metall. Mater. Trans. A, 2009, vol. 50A, pp. 44-50.
37. D.J. Lloyd and L.R. Morris: Acta Metall., 1977, vol. 25, pp. 857-61.10.1016/0001-6160(77)90170-5 ↗
38. B. Jaoul: J. Mech. Phys. Solids, 1961, vol. 9, pp. 69-90.10.1016/0022-5096(61)90026-6 ↗
39. D.W. Moon: Mater. Sci. Eng., 1971, vol. 8, pp. 235-43.10.1016/0025-5416(71)90077-2 ↗
40. V.S. Ananthan and E.O. Hall: Acta Metall. Mater., 1991, vol. 39, pp. 3153-60.10.1016/0956-7151(91)90049-7 ↗
41. G.B. Olson and M. Cohen: Metall. Trans., 1975, vol. 6, pp. 791–95.10.1007/BF02672301 ↗
42. K.P. Staudhammer, L.E. Murr, and S.S. Hecker: Acta Metall., 1983, vol. 31, pp. 267-74.10.1016/0001-6160(83)90103-7 ↗
43. C.X. Huang, K. Wang, S.D. Wu, Z.F. Zhang, and S.X. Li: Acta Mater., 2006, vol. 54, pp. 655-65.10.1016/j.actamat.2005.10.002 ↗
44. R.D.K. Misra, B.R. Kumar, M. Somani, and P. Karjalainen: Scripta Mater., 2008, vol. 59, pp. 79-82.10.1016/j.scriptamat.2008.02.028 ↗
45. P.D. Zavattieri, V. Savic, L.G. Hector Jr., J.R. Fekete, W. Tong, and Y. Xuan: Int. J. Plast., 2009, vol. 25, pp. 2298-330.10.1016/j.ijplas.2009.02.008 ↗
46. L. Chen, H.S. Kim, S.K. Kim, and B.C. De Cooman: ISIJ Int., 2007, vol. 47, pp. 1804-12.10.2355/isijinternational.47.1804 ↗
47. L.H. De Almeida, I. Le May, P.R.O. Emygdio: Mater. Charact., 1998, vol. 41, pp. 137-50.10.1016/S1044-5803(98)00031-X ↗