journal article·2008-02

On the Onset of a Steady State in Body-Centered Cubic Iron during Severe Plastic Deformation at Low Homologous Temperatures

A. Vorhauer, R. Pippan

Publisher page

Abstract

Armco Iron was severely deformed by means of a high-performance, high-pressure torsion (HPT) tool at a hydrostatic pressure of 5.4 GPa at low homologous temperatures, Tm, between 0.08 and 0.40 Tm. The flow stress was estimated from the measured torque during severe plastic deformation (SPD). At all investigated deformation conditions, a saturation in the flow stress at large strains without any decline was obtained. It is shown that this occurrence of a “steady state” at low homologous temperatures is significantly influenced by the deformation parameters, whereby an increase in deformation temperature or a decrease in strain rate results in a decrease in onset strain and an increase in flow stress in both the steady state and the size and aspect ratio of the structural elements. The Zener–Hollomon parameter is used to analyze the mechanical and microstructural properties as a function of the processing parameters; this shows that the investigated range of deformation conditions is divided into two regimes. For comparable high-deformation temperatures, the occurrence of a steady state is ascribed to a process similar to geometric dynamic recrystallization (DRX). Possible reasons for the occurrence of a different behavior in the low homologous temperature regime are discussed; the size of the crystallites formed during straining by the subdivision of the initial grains is considered to play an important role.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (57)

Show source-provided references
1. R.Z. Valiev, R.K. Islamgaliev, I.V. Alexandrov: Prog. Mater. Sci., 2000, vol. 45, pp. 103–8910.1016/S0079-6425(99)00007-9 ↗
2. M.J. Zehetbauer, J. Kohout, E. Schafler: J. Alloys Compd., 2004, vol. 378, pp. 329–3410.1016/j.jallcom.2004.01.039 ↗
3. M. Zehetbauer: Acta Mater., 1993, vol. 41, pp. 589–9910.1016/0956-7151(93)90089-B ↗
4. Y. Iwahashi, Z. Horita, M. Nemoto: Acta Mater., 1998, vol. 46 (9), pp. 3317–3110.1016/S1359-6454(97)00494-1 ↗
5. B.Q. Han, S. Yue: Mater. Process. Technol., 2003, vol. 136, pp. 100–0410.1016/S0924-0136(02)01014-2 ↗
6. S.H. Lee, T. Sakai, D.H. Shin: Mater. Trans., 2003, vol. 44 (7), pp. 1382–8510.2320/matertrans.44.1382 ↗
7. A. Vorhauer, R. Pippan: Scripta Mater., 2004, vol. 51, pp. 921–2510.1016/j.scriptamat.2004.04.025 ↗
8. C. Xu, M. Furukawa, Z. Horita: Acta Mater., 2003, vol. 51, pp. 6139–4910.1016/S1359-6454(03)00433-6 ↗
9. F.J. Humphreys, P.B. Prangnell, J.R. Bowen: Philos. Trans. R. Soc. London, Ser. A, 1999, vol. 357, pp. 1663–8110.1098/rsta.1999.0395 ↗
10. P.J. Apps, M. Berta, P.B. Prangnell: Acta Mater., 2005, vol. 53, pp. 499–51110.1016/j.actamat.2004.09.042 ↗
11. D.H. Shin, B.D. Ahn, and H.S. Cho: in Ultrafine Grained Materials II, D.H. Shin and T.C. Lowe, eds., Minerals, Metals and Materials Society, Warrendale, PA, 2004, pp. 421–26.
12. N. Tsuji, Y. Ito, Y. Saito: Scripta Mater., 2002, vol. 47, pp. 893–9910.1016/S1359-6462(02)00282-8 ↗
13. D.H. Shin, J.J. Pak, Y.K. Kim: Mater. Sci. Eng., 2002, vol. 323, pp. 409–1510.1016/S0921-5093(01)01395-8 ↗
14. A. Vorhauer, S. Kleber, R. Pippan: Mater. Sci. Eng., A, 2005, vols. 410–411, pp. 281–8410.1016/j.msea.2005.08.119 ↗
15. R.Z. Valiev: Adv. Eng. Mater., 2003, vol. 5 (5), pp. 296–30010.1002/adem.200310089 ↗
16. T. Hebesberger, H.P. Stüwe, A. Vorhauer, R. Pippan: Acta Mater., 2005, vol. 53, pp. 393–40210.1016/j.actamat.2004.09.043 ↗
17. H.P. Stüwe: Adv. Eng. Mater., 2003, vol. 5, pp. 291–30010.1002/adem.200310085 ↗
18. F. Wetscher: unpublished research, Hilti, Lichtenstein, 2005.
19. F. Wetscher and R. Pippan: Philos. Mag.., 2006, vol. 86, pp. 5867–8310.1080/14786430600838288 ↗
20. W.H. Huang, C.Y. Yu, P.W. Kao: Mater. Sci. Eng., 2004, vol. 366, pp. 221–2810.1016/j.msea.2003.08.033 ↗
21. T. Sakai, J.J. Jonas: Acta Metall., 1984, vol. 32, pp. 189–20910.1016/0001-6160(84)90049-X ↗
22. S.J. Hales, T.R. McNelly, H.J. McQueen: Metall. Trans. A, 1991, vol. 22A, pp. 1037–4710.1007/BF02661097 ↗
23. K. Tsuzaki, X. Huang, T. Maki: Acta Mater., 1996, vol. 44, pp. 4491–9910.1016/1359-6454(96)00080-8 ↗
24. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, Pergamon Press, Oxford, 1996, pp. 127–392
25. S. Gourdet, F. Montheillet: Mater. Sci. Eng., A, 2000, vol. A283, pp. 274–8810.1016/S0921-5093(00)00733-4 ↗
26. H.J. McQueen, E. Evangelista, M.E. Kassner: Z. Metallkd., 1991, vol. 82, pp. 336–45
27. H.J. McQueen, E. Evangelista: Czech. J. Phys., B, 1988, vol. 38, pp. 359–7210.1007/BF01605405 ↗
28. A. Belyakov, T. Sakai, H. Miura: ISIJ Int., 1999, vol. 39, pp. 592–9910.2355/isijinternational.39.592 ↗
29. A. Belyakov, T. Sakai, H. Miura: Acta Mater., 2002, vol. 50, pp. 1547–5710.1016/S1359-6454(02)00013-7 ↗
30. M.E. Kassner, H.J. McQueen, E. Evangelista: Mater. Sci. Forum, 1993, vols. 113–115, pp. 151–5610.4028/www.scientific.net/MSF.113-115.151 ↗
31. N. Tsuji, R. Ueji, and Y. Ito: Proc. 21st Riso Int. Symp. on Materials Science, Riso National Laboratory, Denmark, 200, pp. 105–14.
32. M.R. Druby, F.J. Humphreys: Acta Metall., 1986, vol. 34, pp. 2259–7110.1016/0001-6160(86)90171-9 ↗
33. P. Cizek, B.P. Wynne: Mater. Sci. Eng., A, 1997, vol. 230, pp. 88–9410.1016/S0921-5093(97)00087-7 ↗
34. A. Belyakov, R. Kaibyshev, R. Zaripova: Mater. Sci. Forum, 1993, vols. 113–115, pp. 385–8910.4028/www.scientific.net/MSF.113-115.385 ↗
35. C.G. Schmidt, C.M. Young, B. Walser: Metall. Trans. A, 1982, vol. 13A, pp. 447–5610.1007/BF02643353 ↗
36. H.J. McQueen, W.A. Wong, J.J. Jonas: Can. J. Phys., 1967, vol. 45, pp. 1225–3910.1139/p67-091 ↗
37. W.A. Wong, J.J. Jonas: Trans. TMS-AIME, 1968, vol. 242, pp. 2271–80
38. H.J. McQueen, N. Ryum: Scand. J. Metall., 1985, vol. 14, pp. 183–94
39. H.J. McQueen, W. Blum: Mater. Sci. Eng., A, 2004, vol. 290, pp. 95–10710.1016/S0921-5093(00)00933-3 ↗
40. J. Philibert: Atom Movements—Diffusion and Mass Transport in Solids, Number 110, Les Editions de Physique, Les Ulis, France, 1991, pp. 74–81.
41. D.W. James, G.M. Leak: Philos. Mag., 1966, vol. 14, pp. 701–1310.1080/14786436608211966 ↗
42. H.J. Frost and M.F. Ashby: Deformation-Mechanism Maps—The Plasticity and Creep of Metals and Ceramics, Pergamon Press, Oxford, 1982, pp. 60–74.
43. H.J. McQueen, J.K. Solberg, N. Ryum: Philos. Mag. A, 1989, vol. 60, pp. 447–7110.1080/01418618908213873 ↗
44. G. Glover, C.M. Sellars: Metall. Trans., 1973, vol. 4, pp. 765–7510.1007/BF02643086 ↗
45. F. Schuh, M. von Heimendahl: Z. Metallkd., 1974, vol. 65, pp. 346–52
46. A. Korbel, M. Richer, J. Richert: Deformation in Polycrystals: Mechanism and Microstructures, Riso National Laboratory, Roskilde, Denmark, 1981, pp. 445–50
47. H. Hero, C.J. Simenson: Scand. J. Metall., 1972, vol. 1, pp. 115–20
48. E.V. Kozlov, A.N. Zhdanov, N.A. Popova: Mater. Sci. Eng., A, 2004, vols. A387–A389, pp. 789–9410.1016/j.msea.2003.12.081 ↗
49. Y. Huang, T.G. Langdon: Mater. Sci. Eng., A, 2003, vol. 358, pp. 114–2110.1016/S0921-5093(03)00268-5 ↗
50. R.Z. Valiev, Y.V. Ivanishenko, E.F. Rauch: Acta Mater., 1996, vol. 44, pp. 4705–1210.1016/S1359-6454(96)00156-5 ↗
51. S. Takaki, K. Kawasaki, Y. Kimura: Mater. Process. Technol., 2001, vol. 117, pp. 359–6310.1016/S0924-0136(01)00797-X ↗
52. B. Derby: Acta Metall. Mater., 1991, pp. 955–62.10.1016/0956-7151(91)90295-C ↗
53. H.P. Stüwe, H. Turk: Z. Metallkd., 1964, vol. 55, pp. 699–703
54. M. Zhou, M.P. Clode: Mech. Mater., 1998, vol. 27, pp. 63–7610.1016/S0167-6636(97)00035-5 ↗
55. F. Wetscher, A. Vorhauer, R. Pippan: Mater. Sci. Eng., A, 2005, vols. 410–411, pp. 213–1610.1016/j.msea.2005.08.027 ↗
56. D.S. Fields and A.W. Backofen: in Proc. ASTM, 1957, vol. 57, pp. 1259–72.
57. W. Ecker: Master’s thesis, University of Leoben, Austria, 2004.