Microstructure Evolution during Friction Stir Welding of Mill-Annealed Ti-6Al-4V
Source abstract
Abstract
In this study, mill-annealed Ti-6Al-4V plates were successfully friction stir welded over a wide range of processing parameters using a tungsten-1 pct La2O3 tool. Two K-type thermocouples embedded in the tool indicated that approximately 25 pct of the heat generated during welding was transferred out of the workpiece and into the tool. The thermocouple data, combined with observations of the microstructure, indicated that the stir zone of all welds exceeded the β transus. The microstructure and texture of two representative welds made just above and high above the β transus were investigated with scanning electron microscopy and electron backscatter diffraction (EBSD). The β phase orientations were reconstructed with a fully automated technique from the as-collected α phase data through knowledge of the Burgers orientation relationship. The results suggest that the fine β grains in the stir zone are formed from the base material ahead of the advancing tool by dissolution of secondary and primary α phase, and there is no further recrystallization. These grains subsequently deform by slip and rotate toward the orientations that are most stable with respect to the shear deformation induced by the tool. In the highest temperature weld, diffusion tool wear in the form of periodically spaced bands provided an internal marker of the tool/workpiece interface during welding. The flow patterns evident within the tungsten-enriched bands suggest that flow is considerably more chaotic on the advancing side than in the central stir zone.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (57)
Show source-provided references
1. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Church, P. Templesmith, and C.J. Dawes: International Patent Application No. PCT/GB92/02203.
2. W.D. Lockwood, B. Tomaz, and A.P. Reynolds: Mater. Sci. Eng. A, 2002, vol. 323, pp. 348–53.10.1016/S0921-5093(01)01385-5 ↗
3. C.G. Rhodes, M.W. Mahoney, W.H. Bingel, R.A. Spurling, and C.C. Bampton: Scripta Mater., 1997, vol. 36 (1), pp. 69–75.10.1016/S1359-6462(96)00344-2 ↗
4. W.B. Lee, Y.M. Yeon, and S.B. Jung: Scripta Mater., 2003, vol. 49, pp. 423–28.10.1016/S1359-6462(03)00301-4 ↗
5. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R, 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
6. J. Schneider, R. Beshears, and A.C. Nunes, Jr.: Mater. Sci. Eng. A, 2006, vols. 435–436, pp. 294–304.
7. T.U. Seidel and A.P. Reynolds: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2879–84.10.1007/s11661-001-1038-1 ↗
8. A.L. Pilchak, M.C. Juhas, and J.C. Williams: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 401–08.10.1007/s11661-006-9061-x ↗
9. D.P. Field, T.W. Nelson, Y. Hovanski, and K.V. Jata: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2869–77.10.1007/s11661-001-1037-2 ↗
10. R.W. Fonda, J.F. Bingert, and K.J. Colligan: Scripta Mater., 2004, vol. 51, pp. 243–48.10.1016/j.scriptamat.2004.04.017 ↗
11. R.W. Fonda, J.A. Wert, A.P. Reynolds, and W. Tang: Sci. Technol. Weld. Join., 2007, vol. 12 (4), pp. 304–10.10.1179/174329307X197557 ↗
12. A.P. Reynolds, E. Hood, and W. Tang: Scripta Mater., 2005, vol. 52, pp. 491–94.10.1016/j.scriptamat.2004.11.009 ↗
13. K.E. Knipling and R.W. Fonda: Scripta Mater., 2009, vol. 60, pp. 1097–1100.10.1016/j.scriptamat.2009.02.050 ↗
14. A.L. Pilchak: Ph.D. Dissertation, The Ohio State University, Columbus, OH, 2009.
15. J.-H. Cho, D.E. Boyce, and P.R. Dawson: Mater. Sci. Eng. A, 2005, vol. 398, pp. 146–63.10.1016/j.msea.2005.03.002 ↗
16. J.-H. Cho and P.R. Dawson: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1147–64.10.1007/s11661-006-1093-8 ↗
17. M.M.Z. Ahmed, B.P. Wynne, W.M. Rainforth, and P.L. Threadgill: Scripta Mater., 2008, vol. 59, pp. 507–10.10.1016/j.scriptamat.2008.04.047 ↗
18. S. Mironov, Y. Zhang, Y.S. Sato, and H. Kokawa: Scripta Mater., 2008, vol. 59, pp. 511–14.10.1016/j.scriptamat.2008.04.038 ↗
19. M.C. Juhas, G.B. Viswanathan, and H.L. Fraser: Proc. 2nd Symp. on Friction Stir Welding, Gothenburg, Sweden, June 2000 (CD proc.).
20. T.J. Lienert, K.V. Jata, R. Wheeler, and V. Seetharaman: Proc. Joining of Advanced and Specialty Materials III, ASM INTERNATIONAL, Materials Park, OH, 2001, pp. 160–67.
21. A.J. Ramirez and M.C. Juhas: Mater. Sci. Forum, 2003, vols. 426–432, pp. 2999–3004.10.4028/www.scientific.net/MSF.426-432.2999 ↗
22. Y. Zhang, Y.S. Sato, H. Kokawa, S.H.C. Park, and S. Hirano: Mater. Sci. Eng. A, 2008, vol. 485, pp. 448–55.10.1016/j.msea.2007.08.051 ↗
23. L. Zhou, H.J. Liu, and Q.W. Liu: J. Mater. Sci., 2010, vol. 45, pp. 39–45.10.1007/s10853-009-3881-1 ↗
24. S. Mironov, Y. Zhang, Y.S. Sato, and H. Kokawa: Scripta Mater., 2008, vol. 59, pp. 27–30.10.1016/j.scriptamat.2008.02.014 ↗
25. S.C. Wang, M. Aindow, and M.J. Starink: Acta Mater., 2003, vol. 51, pp. 2485–03.10.1016/S1359-6454(03)00035-1 ↗
26. N. Karogal: Master’s Thesis, The Ohio State University, Columbus, OH, 2002.
27. A.L. Pilchak, Z.T. Li, J.J. Fisher, A.P. Reynolds, M.C. Juhas, and J.C. Williams: Friction Stir Welding and Processing IV, R.S. Mishra, M.W. Mahoney, T.J. Lienert, and K.V. Jata, eds., TMS, Warrendale, PA, 2007, pp. 419–27.
28. C. Leyens and M. Peters: Titanium and Titanium Alloys, Wiley-VCH, Cologne, 2003, pp. 1–34.10.1002/3527602119 ↗
29. W.B. Lee C.Y. Lee, W.S. Chang, Y.M. Yeon, and S.B. Jung: Mater. Lett., 2005, vol. 59, pp. 3315–18.10.1016/j.matlet.2005.05.064 ↗
30. A.L. Pilchak, M.C. Juhas, and J.C. Williams: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 435–37.10.1007/s11661-006-9059-4 ↗
31. A.L. Pilchak, M.C. Juhas, and J.C. Williams: Welding in the World, IIW-3 Conf. Proc., Dubrovnik, Croatia, 2008, vol. 52 (9–10), research supplement, pp. 60–68.10.1007/BF03266670 ↗
32. M. Boivineau, C. Cagran, D.E. Doytier, V. Eyraud, M.-H. Nadal, B. Wilthan, and G. Pottlacher: Int. J. Thermophys., 2006, vol. 27 (2), pp. 507–29.10.1007/PL00021868 ↗
33. J.C. Williams, R.G. Baggerly, and N.E. Paton: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 837–50.10.1007/s11661-002-0153-y ↗
34. M.G. Glavicic, P.A. Kobryn, T.R. Bieler, and S.L. Semiatin: Mater. Sci. Eng. A, 2003, vol. 346, pp. 50–59.10.1016/S0921-5093(02)00535-X ↗
35. M.G. Glavicic, P.A. Kobryn, T.R. Bieler, and S.L. Semiatin: Mater. Sci. Eng. A, 2003, vol. 351, pp. 258–64.10.1016/S0921-5093(02)00844-4 ↗
36. W.G. Burgers: Physica, 1934, vol. 1, pp. 561–86.10.1016/S0031-8914(34)80244-3 ↗
37. A.L. Pilchak and J.C. Williams: Metall. Mater. Trans. A, DOI: 10.1007/s11661-010-0434-9.10.1007/s11661-010-0434-9 ↗
38. C. Cayron: Acta Cryst. Sect. A Found. Crystall., 2006, vol. A62, pp. 21–40.10.1107/S010876730503686X ↗
39. G. Lütjering and J.C. Williams: Titanium, Springer-Verlag, New York, NY, 2003.10.1007/978-3-540-71398-2 ↗
40. T. Long, W. Tang, and A.P. Reynolds: Sci. Technol. Weld. Join., 2007, vol. 12 (4), pp. 311–17.10.1179/174329307X197566 ↗
41. ASM Metals Handbook, 10th ed., vol. 2, Properties and Selection of Non-Ferrous Alloys and Special Purpose Materials, ASM INTERNATIONAL, Materials Park, OH, 1990, p. 562.
42. Y.J. Chao, X. Oi, and W. Tang: J. Manufact. Sci. Eng.–Trans. ASME, 2003, vol. 125 (1), pp. 138–45.10.1115/1.1537741 ↗
43. G. Lütjering: Mater. Sci. Eng. A, 1998, vol. 243, pp. 32–45.10.1016/S0921-5093(97)00778-8 ↗
44. T.R. Bieler and S.L. Semiatin: Int. J. Plast., 2002, vol. 18, pp. 1165–89.10.1016/S0749-6419(01)00057-2 ↗
45. L. Germain, N. Gey, M. Humbert, P. Bocher, and M. Jahazi: Acta Mater., 2005, vol. 53, pp. 3535–43.10.1016/j.actamat.2005.03.043 ↗
46. M. Peters, A. Gysler, and G. Lütjering: Titanium ’80 Science and Technology, Proc. 4th Int. Conf. on Titanium, H. Kimura and O. Izumi, eds., Kyoto, 1980, pp. 1777–86.
47. M. Hölscher, D. Raabe, and K. Lücke: Steel Res., 1991, vol. 62 (12), pp. 567–75.10.1002/srin.199100451 ↗
48. U.F. Kocks, C.N. Tomé, and H.-R. Wenk: Texture and Anisotropy: Preferred Orientations in Polycrystals and Their Effect on Materials Properties, Cambridge University Press, New York, NY, 1998, pp. 195, 327–91.
49. D. Bhattacharyya, G.B. Viswanathan, S.C. Vogel, D.J. Williams, V. Venkatesh, and H.L. Fraser: Scripta Mater., 2006, vol. 54, pp. 231–36.10.1016/j.scriptamat.2005.09.026 ↗
50. J. Baczynski and J.J. Jonas: Acta Mater., 1996, vol. 44 (11), pp. 4273–88.10.1016/1359-6454(96)00114-0 ↗
51. S. Li, I.J. Beyerlein, and M.A.M. Bourke: Mater. Sci. Eng. A, 2005, vol. 493, pp. 66–77.10.1016/j.msea.2004.11.032 ↗
52. N. Stanford and P.S. Bate: Acta Mater., 2004, vol. 52, pp. 5215–24.10.1016/j.actamat.2004.07.034 ↗
53. L. Zeng and T.R. Bieler: Mater. Sci. Eng. A, 2005, vol. 392, pp. 403–14.10.1016/j.msea.2004.09.072 ↗
54. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, R.A. Spurling, and W.H. Bingel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955–64.10.1007/s11661-998-0021-5 ↗
55. R.W. Fonda and J.F. Bingert: Scripta Mater., 2007, vol. 57, pp. 1052–55.10.1016/j.scriptamat.2007.06.068 ↗
56. Landolt-Börnstein–Group IV Physical Chemistry: Ti-W Phase Diagram, Springer-Verlag, 1998, vol. 5, pp. 1–2.
57. S. Zhang, J.F. Li, J.X. Deng, and Y.S. Li: Int. J. Adv. Manuf. Technol., 2009, vol. 44, pp. 17–25.10.1007/s00170-008-1803-z ↗