journal article·2009-08Open access

Enhanced Mechanical Properties of a Novel High-Nitrogen Cr-Mn-Ni-Si Austenitic Stainless Steel via TWIP/TRIP Effects

M. Pozuelo, J.E. Wittig, J.A. Jiménez, G. Frommeyer

Abstract

Temperature- and strain-rate-dependent mechanical properties of a high-nitrogen austenitic stainless steel containing smaller amounts of nickel than conventional austenitic nickel-chromium stainless steels were investigated with special attention to the formation of martensite or mechanical twins during plastic deformation (TWIP/TRIP effect). After recrystallization treatment at 1050 °C for 0.5 hour, an equiaxed fully austenitic microstructure possessing annealing twins was observed. Tensile tests were carried out at strain rates ranging from 10 −5 to 10 −2 s −1 in the temperature range from −196 °C to 400 °C. Deformation-induced austenite-to-martensite transformation occurred at temperatures below 0 °C. From room temperature up to 200 °C, plastic deformation is controlled by dislocation glide and mechanical twinning. At temperatures above 200 °C, no deformation-induced structural changes were observed. The formations of bcc α ′-martensite and hcp ε -martensite, or twins during plastic deformation, were analyzed by optical microscopy, transmission electron microscopy (TEM), and X-ray diffraction.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. S. Malm and T. Pauly: 5th Eur. Stainless Steel Science and Market Congr., Sevilla, Sept. 27–30, 2005, pp. 11–16.
2. P.J. Cunat: The Euro Inox Handbook of Stainless Steel, Euro Inox Publications, Brussels, 2002, pp. 1–86.
3. S.K. Banerji: Met. Progr., 1978, vol. 113 (4), pp. 59–62.
4. G.T. Haddick, L.D. Thompson, E.R. Parker, and V.F. Zackay: Met. Progr., 1978, vol. 114 (6), pp. 37–40.
5. J. Demestre, R. Leveque, and A. Mercier: Rev. Metall. Paris, 1970, vol. 67, pp. 399–412.10.1051/metal/197067050399 ↗
6. J.C. Garcia, N. Rosas, and R.T. Rioja: Met. Progr., 1982, vol. 122 (3), pp. 47–50.
7. R. Wang and F.H. Beck: Met. Progr., 1983, vol. 123 (4), pp. 72–76.
8. C.R. Clyton and I. Olefjord: in Corrosion Mechanism in Theory and Practice, P. Marcus and J. Quadar, eds., Marcel Dekker, New York, NY, 1995, pp. 175–99.
9. G. Herting, I. Odnevall Wallinder, and C. Leygraf: Corr. Sci., 2007, vol. 49, pp. 103–11.10.1016/j.corsci.2006.05.008 ↗
10. J. Charles: 5th Eur. Stainless Steel Science and Market Congr., Sevilla, Sept. 27–30, 2005, pp. 19–27.
11. E. Werner: Mater. Sci. Eng. A, 1988, vol. 101, pp. 93–98.10.1016/0025-5416(88)90796-3 ↗
12. R.P. Reed: J. Met., 1989, vol. 41, pp. 16–21.
13. M.O. Speidel and R.M. Pedrazzoli: Mater. Performance, 1992, vol. 31, pp. 59–61.
14. J.W. Simmons: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2085–2101.10.1007/BF02670680 ↗
15. H. Chandra Holm, P.J. Uggowitzer, and M.O. Speidel: Scripta Metall., 1987, vol. 21, pp. 513–18.10.1016/0036-9748(87)90191-8 ↗
16. L. Remy: Acta Metall., 1978, vol. 26 (7), pp. 443–51.10.1016/0001-6160(78)90170-0 ↗
17. G. Frommeyer, U. Brüx, and P. Newman: ISIJ Int., 2003, vol. 43, pp. 438–46.10.2355/isijinternational.43.438 ↗
18. F. Chen, P. Li, S. Chu, and C. Chou: Scripta Metall., 1991, vol. 25, pp. 585–90.10.1016/0956-716X(91)90096-J ↗
19. Q. Dai, R. Yang, and K. Chen: Mater. Characterization, 1999, vol. 42, pp. 21–26.10.1016/S1044-5803(98)00043-6 ↗
20. G.B. Olson and M. Cohen: Metall. Trans. A, 1976, vol. 7A, pp. 1897–1904.
21. P.J. Ferreira and P. Müllner: Acta Mater., 1998, vol. 46, pp. 4479–84.10.1016/S1359-6454(98)00155-4 ↗
22. A.F. Padilha, R.L. Plaut, and P.R. Rios: ISIJ Int., 2003, vol. 433, pp. 135–43.10.2355/isijinternational.43.135 ↗