journal article·2007-08

Characterization of the Carbon and Retained Austenite Distributions in Martensitic Medium Carbon, High Silicon Steel

Donald H. Sherman, Steven M. Cross, Sangho Kim, Fernande Grandjean, Gary J. Long, Michael K. Miller

Publisher page

Abstract

The retained austenite content and carbon distribution in martensite were determined as a function of cooling rate and temper temperature in steel that contained 1.31 at. pct C, 3.2 at. pct Si, and 3.2 at. pct noniron metallic elements. Mossbauer spectroscopy, transmission electron microscopy (TEM), transmission synchrotron X-ray diffraction (XRD), and atom probe tomography were used for the microstructural analyses. The retained austenite content was an inverse, linear function of cooling rate between 25 and 560 K/s. The elevated Si content of 3.2 at. pct did not shift the start of austenite decomposition to higher tempering temperatures relative to SAE 4130 steel. The minimum tempering temperature for complete austenite decomposition was significantly higher (>650 °C) than for SAE 4130 steel (∼300 °C). The tempering temperatures for the precipitation of transition carbides and cementite were significantly higher (>400 °C) than for carbon steels (100 °C to 200 °C and 200 °C to 350 °C), respectively. Approximately 90 pct of the carbon atoms were trapped in Cottrell atmospheres in the vicinity of the dislocation cores in dislocation tangles in the martensite matrix after cooling at 560 K/s and aging at 22 °C. The 3.2 at. pct Si content increased the upper temperature limit for stable carbon clusters to above 215 °C. Significant autotempering occurred during cooling at 25 K/s. The proportion of total carbon that segregated to the interlath austenite films decreased from 34 to 8 pct as the cooling rate increased from 25 to 560 K/s. Developing a model for the transfer of carbon from martensite to austenite during quenching should provide a means for calculating the retained austenite. The maximum carbon content in the austenite films was 6 to 7 at. pct, both in specimens cooled at 560 K/s and at 25 K/s. Approximately 6 to 7 at. pct carbon was sufficient to arrest the transformation of austenite to martensite. The chemical potential of carbon is the same in martensite that contains 0.5 to 1.0 at. pct carbon and in austenite that contains 6 to 7 at. pct carbon. There was no segregation of any substitutional elements.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Advanced Materials Characterization Techniques · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (80)

Show source-provided references
1. D.H. Sherman, B.J. Yang, A.V. Catalina, A.A. Hattiangadi, P. Zhao, L. Chuzhoy, and M.L. Johnson: Proc. THERMEC’2006, Materials Science Forum/Advanced Materials Research, Trans Tech Publications Inc., Uetikon-Zuerich, Switzerland, 2007, vols. 539–543, pp. 4795–80010.4028/0-87849-428-6.4795 ↗
2. M.N. Shabrov, E. Sylven, S. Kim, D.H. Sherman, L. Chuzhoy, C.L. Briant, A. Needleman: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 1745–5510.1007/s11661-004-0083-y ↗
3. W. Li, J. Cai, L. Chuzhoy, D.H. Sherman, K.L. Erickson, R. Shaikh: Heat Treating: Proc. of the 23rd Heat Treating Society Conf., D.H. Herring, R.A. Hill Jr, ed., ASM International, USA, 2006, pp. 175–81
4. A.A. Hattiangadi, J. Cai, L. Chuzhoy, M.L. Johnson: Heat Treating: Proc. of the 23rd Heat Treating Society Conf., D.H. Herring, R.A. Hill Jr, ed., ASM International, USA, 2006, pp. 279–88
5. V. Raghavan: in Martensite, G.B. Olson, W.S. Owen, eds., ASM INTERNATIONAL, Materials Park, OH, 1992, pp. 197–225
6. I. Tamura: in Martensite, G.B. Olson, W.S. Owen, eds., ASM INTERNATIONAL, Materials Park, OH, 1992, pp. 227–42
7. G.B. Olson, A.L. Roitburd: in Martensite, G.B. Olson, W.S. Owen, eds., ASM INTERNATIONAL, Materials Park, OH, 1992, pp. 149–74
8. M. Grujicic, H.C. Ling, D.M. Haezebrouck, W.S. Owen: in Martensite, G.B. Olson, W.S. Owen, eds., ASM INTERNATIONAL, Materials Park, OH, 1992, pp. 175–96
9. S.S. Babu, K. Hono, T. Sakurai: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 499–50810.1007/BF02651591 ↗
10. M. Sarikaya, G. Thomas, J.W. Steeds, S.J. Barnard, and G.D.W. Smith: Int. Conf. on Solid to Solid Phase Transformations, H.I. Aaronson, ed., TMS, Warrendale, PA, 1982, pp. 1421–25
11. J.A. McMahon: Lawrence Berkeley Laboratory Report No. 1181, University of California, Berkeley, CA, 1973.
12. G.R. Speich, K.A. Taylor: in Martensite, G.B. Olson, W.S. Owen, eds., ASM INTERNATIONAL, Materials Park, OH, 1992, pp. 243–75
13. G. Krauss: STEELS: Heat Treatment and Processing Principles, ASM INTERNATIONAL, Metals Park, OH, 1990, pp. 75–76
14. K.A. Taylor, M. Cohen: Progr. Mater. Sci., 1992, vol. 36, pp. 225–72
15. G. Thomas, M. Sarikaya, G.D.W. Smith, S.J. Barnard: Advances in the Physical Metallurgy and Applications of Steels, TMS, London, 1982, pp. 259–65
16. R.G. Thomson, M.K. Miller: Acta Mater., 1998, vol. 46 (6), pp. 2203–1310.1016/S1359-6454(97)00420-5 ↗
17. A.M. Sherman: Ph.D. Thesis, Massachusetts Institute of Technology, Cambridge, MA, 1967
18. J.A. McMahon and G. Thomas: Proc. Int. Conf. on the Microstructure and Design of Alloys, Institute of Metals, London, 1973, vol. 1, pp. 180–84
19. R.C. Thomson, M.K. Miller: Scripta Metall. Mater., 1995, vol. 32, pp. 149–5410.1016/S0956-716X(99)80028-4 ↗
20. B.P.J. Sandvik, C.M. Wayman: Metallography, 1983, vol. 16, pp. 429–4710.1016/0026-0800(83)90031-9 ↗
21. K.A. Taylor: Sc.D. Thesis, Massachusetts Institute of Technology, Cambridge, MA, 1985
22. A.G. Khachaturyan: Theory of Structural Transformations is Solids, John Wiley and Sons, Inc., New York, NY, 1983.
23. S. Nagakura, M. Toyoshima: Trans. Jpn. Inst. Met., 1979, vol. 20, pp. 100–1010.2320/matertrans1960.20.100 ↗
24. M. Kusunoki, S. Nagakura: J. Appl. Cryst., 1981, vol. 14, pp. 329–3610.1107/S0021889881009485 ↗
25. Y. Nakamura, S. Nagakura: Proc. 7th Int. Conf. High Voltage Electron Microscopy, R.M. Fisher, R. Gronsky, K.H. Westmacott, eds., Lawrence Berkeley Laboratory, CA, USA, 1983, pp. 221–26
26. S. Nagakura, Y. Hirotsu, M. Kusunoki, T. Suzuki, Y. Kakamura: Metall. Trans. A, 1983, vol. 14A, pp. 1025–3110.1007/BF02659851 ↗
27. M. Kusunoki, S. Nagakura: Trans. Jpn. Inst. Met., 1984, vol. 25, pp. 517–2210.2320/matertrans1960.25.517 ↗
28. K.A. Taylor, J.B. Vander Sande, M. Cohen: Metall. Trans. A, 1993, vol. 24A, pp. 2585–8810.1007/BF02646537 ↗
29. S.B. Ren, T. Tadaki, K. Shimizu, X.T. Wang: Metall. Trans. A, 1995, vol. 26A, pp. 2001–0510.1007/BF02670672 ↗
30. W. Xiaotian, R. Ziaobing: Trans. Met. Heat Treat., 1996, vol. 17, pp. 1–6
31. S.S. Babu, K. Hono, T. Sakurai: Appl. Surf. Sci., 1993, vol. 67, pp. 321–2710.1016/0169-4332(93)90333-7 ↗
32. R.C. Thomson, M.K. Miller: Appl. Surf. Sci., 1995, vols. 87–88, pp. 185–9310.1016/0169-4332(94)00496-X ↗
33. M. Sarikaya, A.K. Jhingan, G. Thomas: Metall. Trans. A, 1983, vol. 14A, pp. 1121–3310.1007/BF02659860 ↗
34. R.G. Thomson, M.K. Miller: Appl. Surf. Sci., 1996, vols. 94–95, pp. 313–1910.1016/0169-4332(95)00392-4 ↗
35. H. Kwon, C.H. Kim: Metall. Trans. A, 1983, vol. 14A, pp. 1389–94.10.1007/BF02664822 ↗
36. R.A. Clark, G. Thomas: Metall. Trans. A, 1975, vol. 6A, p. 96910.1007/BF02661349 ↗
37. N.C. Law, P.R. Howell, D.V. Edmonds: Met. Sci., 1979, vol. 13, p. 50710.1179/030634579790438309 ↗
38. R.M. Horn RM, R.O. Ritchie: Metall. Trans. A, 1978, vol. 9A, p. 1039–5310.1007/BF02652208 ↗
39. C.J. Barton: Acta Metall., 1969, vol. 17, pp. 1085–9310.1016/0001-6160(69)90053-4 ↗
40. A. Böttger, P.J. Warren, G.D.W. Smith, M.J. van Genderen, S.J. Sijbrandij, E.J. Mittemeijer: Mater. Sci. Forum, 1999, vols. 318–320, pp. 103–0810.4028/www.scientific.net/MSF.318-320.103 ↗
41. M.K. Miller, P.A. Beaven, G.D.W. Smith: Metall. Trans. A, 1981, vol. 12A, pp. 1187–204
42. R. Padmanabhan, W.E. Wood: Mater. Sci. Eng., 1984, vol. 65, pp. 289–9710.1016/0025-5416(84)90090-9 ↗
43. S.J. Barnard, G.D.W. Smith, M. Sarikaya, G. Thomas: Scripta Metall., 1981, vol. 15, pp. 387–9210.1016/0036-9748(81)90216-7 ↗
44. A.M. Sherman, G.T. Eldis, M. Cohen: Metall. Trans. A, 1983, vol. 14A, pp. 995–1005.10.1007/BF02659847 ↗
45. K.A. Taylor, L. Chang, G.B. Olson, G.D.W. Smith, M. Cohen, J.B. Vander Sand: Metall. Trans. A, 1989, vol. 20A, pp. 2717–3710.1007/BF02670166 ↗
46. H.K.D.H. Bhadeshia, D.V. Edmonds: Met. Sci., 1979, vol. 13, p. 325
47. C.L. Briant: Mater. Sci. Technol., 1989, vol. 5, p. 13810.1179/mst.1989.5.2.138 ↗
48. G. Thomas: Metall. Trans. A, 1978, vol. 9A, p. 43910.1007/BF02646396 ↗
49. M. Sarikaya, Steinberg G. Thomas: Metall. Trans. A, 1982, vol. 13A, pp. 2227–3710.1007/BF02648394 ↗
50. A.G. Allten P. Payson: Trans. ASM, 1953, vol. 45, pp. 498–532
51. C.H. Shih B.L. Averbach, Morris Cohen: Trans. ASM, 1956, vol. 48, pp. 86–118
52. C.J. Altstetter, M. Cohen, B.L. Averbach: Trans. ASM, 1962, vol. 55, pp. 287–300
53. T.F. Kelly, P.P. Camus, D.J. Larson, L.M. Holzman, S.S. Bajikar: Ultramicroscopy, 1996, vol. 62, pp. 29–4210.1016/0304-3991(95)00086-0 ↗
54. T.F. Kelly, D.J. Larson: Mater. Charact., 2000, vol. 44, pp. 59–8510.1016/S1044-5803(99)00055-8 ↗
55. D.L. Williamson, R.G. Schupmann, J.P. Materkowski, G. Krauss: Metall. Trans. A, 1979, vol. 10A, pp. 379–82.10.1007/BF02658350 ↗
56. J. Hesse: Nukleonika, 1994, vol. 39, pp. 69–90
57. K.F. Laneri, J. Desimoni, G.J. Zarragoicoechea, A. Fernandez-Guillermet: Phys. Rev. B, 2002, vol. 66, p. 13420110.1103/PhysRevB.66.134201 ↗
58. J. Desimoni: Hyperfine Int., 2001, vol. 134, pp. 93–10210.1023/A:1013887927490 ↗
59. J.A. Peters, J.V. Bee, B. Kolk, G.G. Garrett: Acta Metall., 1989, vol. 37, pp. 675–8610.1016/0001-6160(89)90251-4 ↗
60. PowderDiffraction Files, The International Center for Diffraction Data, Newton Square, PA
61. B.W. Christ, P.M. Giles: Trans. TMS-AIME, 1968, vol. 242, pp. 1915–25
62. B. Fultz: in Mössbauer Spectroscopy Applied to Magnetism and Materials Science,” G.J. Long and F. Grandjean, eds., Plenum Press, New York, NY, 1996, vol. 2, pp. 1–31
63. N. Abe, L.H. Schwartz: Mater. Sci. Eng., 1974, vol. 14, pp. 239–5110.1016/0025-5416(74)90105-0 ↗
64. G. Krauss: STEELS: Processing, Structure, and Performance, ASM INTERNATIONAL, Metals Park, OH, 2005, pp. 327–52
65. G. Krauss: STEELS: Processing, Structure, and Performance, ASM INTERNATIONAL, Metals Park, OH, 2005, p. 397
66. R.K.W. Honeycombe, H.K.D.H. Bhadeshia: Steels, Microstructure and Properties, Edward Arnold, London, 1995
67. G. Krauss: Proc. Int. Conf. on Phase Transformations in Ferrous Alloys, TMS, Warrendale, PA, 1984, pp. 101–23
68. H.C. Lee and G. Krauss: Gilbert R. Speich Symp. Proc.: Fundamentals of Aging and Tempering in Bainitic and Martensitic Steel Products, ISS, Warrendale, PA, 1992, pp. 39–43
69. W.S. Owen: Trans. ASM, 1954, vol. 46, pp. 813–29
70. L. Chang, G.D.W. Smith: J. Phys., 1984, vol. 45 (C9), pp. 397–401
71. G.M. Michal, J.A. Slane: Metall. Trans. A, 1986, vol. 17A, pp. 1287–9410.1007/BF02650109 ↗
72. G.M. Michal and J.A. Slane: J. Met., 1986, Jan., pp. 32–3610.1007/BF03257952 ↗
73. B.G. Reisdorf: Trans. TMS-AIME, 1963, vol. 227, pp. 1334–41
74. J. Gordine and I. Codd: J. Iron Steel Inst., 1969, Apr., pp. 461–67
75. G. Le Caër, J.M. Dubois J.P. Senateur: J. Solid State Chem., 1976, vol. 19, pp. 19–2810.1016/0022-4596(76)90145-6 ↗
76. G. Le Caër, E. Bauer-Grosse: Hyperfine Interactions, 1989, vol. 47, pp. 55–6710.1007/BF02351599 ↗
77. J. Wilde, A. Cerezo, G.D.W. Smith, Scripta Mater., 2000, vol. 43, pp. 39–4810.1016/S1359-6462(00)00361-4 ↗
78. F.G. Cabellero, M.K. Miller, S.S. Babu, C. Garcia-Mateo, and C. Garcia de Andrés: Solid-Solid Phase Transformations in Inorganic Materials 2005 Volume 1: Diffusional Transformations, J. Howe, D. Laughlin, J. Lee, U. Dahmen, and W. Soffa, TMS, Warrendale, PA, 2005, pp. 511–16
79. A.W. Cochardt, G. Schoek, H. Wiedersich: Acta Mater, 1955, vol. 3, pp. 533–3710.1016/0001-6160(55)90111-5 ↗
80. M.K. Miller, P.A. Beaven, S.S. Brenner, G.D.W. Smith: Metall. Trans. A, 1983, vol. 14A, p. 1021