journal article·2004-06

Eutectic grains in unmodified and strontium-modified hypoeutectic aluminum-silicon alloys

Stuart D. McDonald, Arne K. Dahle, John A. Taylor, David H. StJohn

Publisher page

Abstract

Additions of strontium to hypoeutectic aluminum-silicon alloys modify the morphology of the eutectic silicon phase from a coarse platelike structure to a fine fibrous structure. Thermal analysis, interrupted solidification, and microstructural examination of sand castings in this work revealed that, in addition to a change in silicon morphology, modification with strontium also causes an increase in the size of eutectic grains. The eutectic grain size increases because fewer grains nucleate, possibly due to poisoning of the phosphorus-based nucleants, that are active in the unmodified alloy. A simple growth model is developed to estimate the interface velocity during solidification of a eutectic grain. The model confirms, independent of microstructural observations, that the addition of 100 ppm strontium increases the eutectic grain size by at least an order of magnitude compared with the equivalent unmodified alloy. The model predicts that the growth velocity varies significantly during eutectic growth. At low strontium levels, these variations may be sufficient to cause transitions between flake and fibrous silicon morphologies depending on the casting conditions. The model can be used to rationally interpret the eutectic grain structure and silicon morphology of fully solidified aluminum-silicon castings and, when coupled with reliable thermal data, can be used to estimate the eutectic grain size.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Solidification and crystal growth phenomena

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. M.G. Day: J. Inst. Met., 1970, vol. 98, pp. 57–59.
2. G. Laslaz: Proc. 4th Int. Conf. on Molten Aluminum Processing, Orlando, FL, July 1995, AFS, Des Plaines, IL, pp. 459–80.
3. X.G. Chen, R. Ellerbrok, and S. Engler: Giessereiforschung, 1990, vol. 42 (1), pp. 1–10.
4. X.G. Chen, R. Ellerbrok, and S. Engler: Giessereiforschung, 1990, vol. 42 (1), pp. 11–18.
5. J.R. Denton and J.A. Spittle: Mater. Sci. Technol., 1985, vol. 1, pp. 305–11.10.1179/mst.1985.1.4.305 ↗
6. C.B. Kim and R.W. Heine: J. Inst. Met., 1964, vol. 92, pp. 367–76.
7. M.D. Hanna, S. Lu, and A. Hellawell: Metall. Trans. A, 1984, vol. 15A, pp. 459–69.10.1007/BF02644969 ↗
8. S.C. Flood and J.D. Hunt: Metal Sci., 1981, vol. 15, pp. 287–94.10.1016/0036-9748(81)90346-X ↗
9. Q.S. Hamed, R. Elliot, and P.S. Cooper: Light Met., 1992, pp. 1391–97.
10. K. Nogita and A.K. Dahle: Mater. Trans. (JIM), 2001, vol. 42 (3), pp. 393–96.10.2320/matertrans.42.393 ↗
11. R. Fuoco, E.R. Correa, and A.V.O. Correa: AFS Trans., 1995, vol. 103, pp. 379–87.
12. A.K. Dahle, K. Nogita, J.W. Zindel, S.D. McDonald, and L.M. Hogan: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 949–59.10.1007/s11661-001-0352-y ↗
13. H. Fredriksson, M. Hillert, and N. Lange: J. Inst. Met., 1973, vol. 101, pp. 285–99.
14. G.L.F. Powell and G.A. Colligan: Metall. Trans., 1971, vol. 2, pp. 1992–95.10.1007/BF02913439 ↗
15. V.D. Belov, A.V. Kurdyumov, and S.V. Inkin: Sov. Non-Ferrous Met. Res., 1981, vol. 9 (6), pp. 497–500.
16. C. Degand, D.M. Stefanescu, and G. Laslaz: Proc. Int. Symp. on Advanced Materials and Technology for the 21st Century, Honolulu, HI, 1995, I. Ohnaka and D.M. Stefanescu, eds., TMS, Warrendale, PA, 1995, pp. 55–63.
17. J. Runyoro and J. Campbell: The Foundryman, 1992, Apr., pp. 117–24.
18. S.D. McDonald: Ph.D. Thesis, The University of Queensland, Brisbane, 2002.
19. J. Tamminen: Ph.D. Thesis, Stockholm University, Stockholm, 1988.
20. C. Charbon and M. Rappaz: Modelling Simulation Mater. Sci. Eng. (UK), 1993, vol. 1 (4), pp. 455–66.10.1088/0965-0393/1/4/009 ↗
21. D.M. Stefanescu, G. Upadhya, and D. Bandyopadhyay: Metall. Trans. A, 1990, vol. 21A, pp. 997–1005.10.1007/BF02656584 ↗
22. N.A. El-Mahallawy, M.A. Taha, A.K. El-Kharbotly, E. Abdel Hakim, and I. Svenson: Mater. Sci. Forum, 1996, vols. 217–222, pp. 347–52.10.4028/www.scientific.net/MSF.217-222.347 ↗
23. R. Elliot and S.M.D. Glenister: Acta Metall., 1980, vol. 28, pp. 1489–94.10.1016/0001-6160(80)90049-8 ↗
24. L.M. Hogan and H. Song: Metall. Trans. A, 1987, vol. 18A, pp. 707–13.10.1007/BF02649487 ↗
25. S.M.D. Glenister and R. Elliot: Met. Sci. J., 1981, vol. 15, pp. 181–83.10.1016/0036-9748(81)90325-2 ↗
26. M. Rappaz: Int. Mater. Rev., 1989, vol. 34 (3), pp. 93–123.10.1179/imr.1989.34.1.93 ↗
27. L. Clapham and R.W. Smith: J. Cryst. Growth, 1986, vol. 79, pp. 866–73.10.1016/0022-0248(86)90566-X ↗
28. L. Clapham and R.W. Smith: Acta Metall., 1989, vol. 37 (1), pp. 303–11.10.1016/0001-6160(89)90288-5 ↗
29. M. Rappaz and D.M. Stefanescu: Solidification Processing of Eutectic Alloys: Proc. Symp., Cincinnati, OH, Oct. 12–15, 1988 D.M. Stefanescu, G.J. Abbaschian, and R.J. Bayuzick, eds., TMS, Warrendale, PA, pp. 133–51.
30. D.C. Jenkinson and L.M. Hogan: J. Cryst. Growth, 1975, vol. 28, pp. 171–87.10.1016/0022-0248(75)90233-X ↗
31. S. Lu and A. Hellawell: Metall. Trans. A, 1987, vol. 18A, pp. 1721–33.10.1007/BF02646204 ↗
32. M.E. Straumanis and E.Z. Aka: J. Appl. Phys., 1952, vol. 23, p. 330.10.1063/1.1702202 ↗
33. C. Yeh, Z.W. Lu, S. Froyen, and A. Zunger: Phys. Rev. B, 1992, vol. 46 (16), pp. 1086–10095.10.1103/PhysRevB.46.10086 ↗
34. C.R. Ho and B. Cantor: J. Mater. Sci., 1995, vol. 30, pp. 1912–20.10.1007/BF00353013 ↗
35. P.B. Crosley and L.F. Mondolfo: AFS Trans., 1966, vol. 74, pp. 53–64.
36. C.R. Ho and B. Cantor: Acta Metall Mater, 1995, vol. 43 (8), pp. 3231–46.10.1016/0956-7151(94)00480-6 ↗
37. K. Nogita, K. Tsujomoto, A.K. Dahle, and J. Drennan: 18th Aus. Conf. on Microscopy and Microanalysis, Deakin University, Geelong, Australia, Feb. 2–6, 2004.
38. G. Chai and L. Bäckerud: AFS Trans., 1992, vol. 100, pp. 847–54.
39. L. Wang and S. Shivkumar: Z. Metallkd., 1995, vol. 86 (6), pp. 441–45.